Delta 28-206 Attaching the SAW to the Stand, Attaching the Belt to the SAW and Motor Pulley

Page 14

ATTACHING THE SAW TO THE STAND

THE BAND SAW IS VERY HEAVY. Use a helper when you attach the saw to the stand.

1.Place the band saw on top of the stand as shown in Fig. 17.

NOTE: Confirm that the pulley is on the same side of the stand as the pulley guard.

2.Align the four holes in the saw with the four holes in the top of the stand.

3.Place an M8 lockwasher and a M8 flat washer on a hex head screw (M8x1.25x40mm). Insert the screw through one of the holes (A) in the saw and the stand.

4.Thread a hex nut (M8x1.25) on the screw and tighten securely.

5.Repeat this process for the other hole (A).

A

B

Fig. 17

6.Attach the belt to the saw and motor pulley. See the section "ATTACHING BELT TO SAW AND MOTOR

PULLEY".

7.Repeat STEPS 3 AND 4 for the two remaining holes (B) Fig. 17 (one of which is shown).

ATTACHING THE BELT TO THE SAW AND MOTOR PULLEY

1.

Place the belt over the saw pulley (A) Fig. 18.

C

 

 

 

NOTE: The model 28-276 has a one-step pulley. The

 

 

 

 

 

 

 

model 28-206 has a two-step pulley (Fig. 18).

 

 

 

 

 

 

 

 

 

2.

Lift the motor and place the other end of the belt

 

 

 

 

 

around the motor pulley (B) Fig. 18. The weight of

 

 

 

 

 

the motor will provide the correct belt tension.

D

 

 

 

 

Operate the machine ONLY with all the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

guards in place and secure.

 

B

 

 

 

 

 

 

3.

Check the alignment of the motor and saw pulley.

 

 

 

A

4.

Loosen the four bolts (C) Fig. 12 that hold the motor

 

Fig. 18

 

 

 

bracket to the motor mounting plate, and adjust the

 

 

 

 

 

 

 

 

position of the motor until the motor pulley and saw

 

 

 

 

 

pulley are aligned.

 

 

 

 

5.Tighten the four bolts that were loosened in STEP 4.

6.Turn bolt (C) Fig. 18, clockwise, until the dampening cap contacts the motor.

7.Back the bolt (C) Fig. 18 out approximately 1/4" and tighten the nut (D) against the top of the stand to hold bolt

(C)in place.

NOTE: Do not use the bolt and dampening washer to tension the belt. These two parts prevent the motor from rising excessively when the motor starts.

ATTACHING THE PULLEY GUARDS

NOTE: The illustration in Fig. 18A shows the stand without the band saw for clarity.

1.Insert the two threaded studs on the lower pulley guard (C) Fig 18A through the two holes in the top of the stand (B).

2.Align the two holes in the upper pulley guard (D) Fig. 18A with the two threaded studs on the lower pulley guard (C). Place the upper pulley guard on the studs of the lower pulley guard.

3.Thread a hex flange nut (M8x1.25) on each of the studs and tighten securely.

D

B

A

Fig. 18A

C

14 - English

Image 14
Contents Contractors Saw Safety Guidelines Definitions Table of ContentsImportant Safety Instructions General Safety Rules Stay ALERT, Watch What YOU are DOING, and USEAdditional Specific Safety Rules Refer to them often Use them to instruct othersPower Connections Extension Cords Fig. CCarton Contents Functional DescriptionModel 28-206 Enclosed Stand Parts Model 28-276 Open Stand Parts Assembly Time Estimate AssemblyAssembly Tools Required Model 28-206 Enclosed Stand AssemblyAlign the holes in the base a , with the holes Model 28-276 Open Stand Assembly Page Attaching the Pulley Guards Attaching the SAW to the StandAttaching the Belt to the SAW and Motor Pulley Attaching Blade to the SAW Connecting Motor Cord to Switch AssemblyDisconnect the machine from the power source Table InsertStarting and Stopping the SAW Locking the Switch in the OFF PositionOperation Tilting the TableAdjusting the Table Stop Adjusting Blade TensionVertical Adjustment of the Upper Blade Guide Assembly Tracking the BladeAdjusting the Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support BearingDust Port Changing Blade Speed for Model 28-206 onlyProbable Cause Troubleshooting GuideCutting Curves Remedy Probable Cause RemedyBand SAW Blades Maintenance ServiceService and Repairs AccessoriesWarranty LA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Conservez CES InstructionsRègles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES DirectivesInstructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur Cordon DE Rallonge Fonctionnement Monophasé À 240 VoltsDésemballage ET Nettoyage Contenu DU CartonAVANT-PROPOS Pièces DU Socle Fermé DU Modèle Pièces DU Socle Ouvert DU Modèle Durée Estimée Pour L’ASSEMBLAGE AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Assemblage DU Socle Fermé DU ModèleFrench Assemblage DU Socle Ouvert DU Modèle French Assemblage DE LA Scie SUR LE Socle Assemblage DES Protecteurs DE PoulieAssemblage DE LA Lame SUR LA Scie Connexion DU Cordon Moteur À L’ENSEMBLE DE L’INTERRUPTEURAssemblage DE LA Table SUR LA Scie Insert DE TableVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT FonctionnementDémarrage ET Arrêt DE Scie Inclinaison DE LA TableRéglage DE LA Butée DE LA Table Réglage DE LA Tension DE LameAlignement DE LA Lame Réglage Vertical DE L’ENSEMBLE DE Guide Supérieur DE LA LameDébrancher l’appareil de la source d’alimentation Utilisation DE L’APPAREIL Goulotte À PoussièreCoupe DE Courbes Problème LA Scie NE Démarre PAS Cause probable SolutionGuide DE Dépannage Problème LA Scie À Ruban Vibre Beaucoup Cause probableProblème LES Lames Cassent Cause probable Problème LA Lame NE S’ALIGNE PAS Cause probableGarder LA Machine Propre EntretienLames DE Scie À Lame Ruban Démarrage ImpossibleGarantie AccessoiriesRemplacement Gratuit DE Létiquette Entretien ET RéparationProposición DE California Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Normas Generales DE Seguridad EL USO DE Esta HerramientaGuarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónEspecificaciones DEL Motor Cordones DE Extensión Fig. D1Prefacio Descripción FuncionalContenido DE Carton Desempaquetado Y LimpiezaPiezas Cerradas DEL Soporte DEL Modelo Base Tornillo de cabeza troncocónica M5 x 0.8 x 10 mm LadoPiezas Abiertas DEL Soporte DEL Modelo Estimación DEL Tiempo DE Ensamblaje EnsamblajeHerramientas DE Ensamblaje Requeridas Montaje DE LA Base DE Soporte Cerrada ModeloNota Apriete libremente el hardware para el ajuste adicional Montaje DE LA Base DE Soporte Abierta Modelo Sobre una superficie planaPage Sujeción DE LA Sierra a LA Base DE Soporte Conectar LA Agujeros DEL Protector DE LA PoleaSujeción DE LA Hoja a LA Sierra Cuerda DEL Motor QUE Conecta a LA Asamblea DE InterruptorSujeción DE LA Mesa a LA Sierra Montaje DE LA Pieza DE Insercion DE MesaBloqueando EL Interruptor EN LA Posicion DE Apagado OperaciónArrancando Y Deteniendo LA Sierra Inclinación DE LA TablaAjuste DE LA Parada DE LA Tabla Ajuste DE LA Tensión DE LA LáminaSeguir LA Lámina Ajuste Vertical DEL Montaje Superior DE LA Guía DE LA LáminaDesconecte la maquina de la fuente de energia Utilizar LA Maquina Puerto DEL PolvoCausa probable Guia Localizacion DE FallasCorte DE Curvas Causa probable RemedioRemedios Mantenga LA Máquina Limpia Hojas DE Sierra DE CintaLocalizacion DE Fallas Mantenimiento Servicio Accesorios Garantia