Delta 28-206, 28-276 Tracking the Blade, Vertical Adjustment of the Upper Blade Guide Assembly

Page 18

TRACKING THE BLADE

Disconnect the machine from the power source!

IMPORTANT: Before tracking the blade, confirm that

A

the blade guides and blade support bearings are clear

 

of the blade.

 

After applying tension to the blade, rotate the wheels

 

slowly forward by hand and observe the blade’s

 

movement. The blade (A) Fig. 31 should travel in the

 

center of the upper tire. If the blade creeps toward the

 

front edge, loosen the wing nut (B) Fig. 32 and turn the

 

thumb screw (C) clockwise. This action draws the blade

 

toward the center of the tire. If the blade creeps toward

Fig. 31

the back edge, turn the thumb screw in the opposite

direction. Adjust the thumb screw (C) Fig. 32 only a

 

fraction of a turn each time.

 

B

C

Never track the blade while the machine

 

is running.

 

After the blade is tracking in the center of the tires,

 

tighten the wing nut (B) Fig. 32.

 

 

Fig. 32

VERTICAL ADJUSTMENT OF THE UPPER BLADE GUIDE ASSEMBLY

Disconnect the machine from the power source!

To adjust the blade guides and bearings:

Set the upper blade guide assembly (A) Fig. 33 as close as possible to the top surface of the workpiece. Loosen the lock knob (B) and move the guide assembly (A) to the desired position.

A

B

Fig. 33

18 - English

Image 18
Contents Contractors Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety Rules Stay ALERT, Watch What YOU are DOING, and USEAdditional Specific Safety Rules Refer to them often Use them to instruct othersPower Connections Extension Cords Fig. CCarton Contents Functional DescriptionModel 28-206 Enclosed Stand Parts Model 28-276 Open Stand Parts Assembly Time Estimate AssemblyAssembly Tools Required Model 28-206 Enclosed Stand AssemblyAlign the holes in the base a , with the holes Model 28-276 Open Stand Assembly Page Attaching the SAW to the Stand Attaching the Belt to the SAW and Motor PulleyAttaching the Pulley Guards Attaching Blade to the SAW Connecting Motor Cord to Switch AssemblyDisconnect the machine from the power source Table InsertStarting and Stopping the SAW Locking the Switch in the OFF PositionOperation Tilting the TableAdjusting the Table Stop Adjusting Blade TensionVertical Adjustment of the Upper Blade Guide Assembly Tracking the BladeAdjusting the Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support BearingDust Port Changing Blade Speed for Model 28-206 onlyTroubleshooting Guide Cutting CurvesProbable Cause Remedy Probable Cause RemedyBand SAW Blades Maintenance ServiceAccessories WarrantyService and Repairs LA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Conservez CES InstructionsRègles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES DirectivesRaccordements Électriques Spécifications DU MoteurInstructions DE Mise À LA Terre Cordon DE Rallonge Fonctionnement Monophasé À 240 VoltsContenu DU Carton AVANT-PROPOSDésemballage ET Nettoyage Pièces DU Socle Fermé DU Modèle Pièces DU Socle Ouvert DU Modèle Durée Estimée Pour L’ASSEMBLAGE AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Assemblage DU Socle Fermé DU ModèleFrench Assemblage DU Socle Ouvert DU Modèle French Assemblage DE LA Scie SUR LE Socle Assemblage DES Protecteurs DE PoulieAssemblage DE LA Lame SUR LA Scie Connexion DU Cordon Moteur À L’ENSEMBLE DE L’INTERRUPTEURAssemblage DE LA Table SUR LA Scie Insert DE TableVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT FonctionnementDémarrage ET Arrêt DE Scie Inclinaison DE LA TableRéglage DE LA Butée DE LA Table Réglage DE LA Tension DE LameAlignement DE LA Lame Réglage Vertical DE L’ENSEMBLE DE Guide Supérieur DE LA LameDébrancher l’appareil de la source d’alimentation Utilisation DE L’APPAREIL Goulotte À PoussièreCoupe DE Courbes Problème LA Scie NE Démarre PAS Cause probable SolutionGuide DE Dépannage Problème LA Scie À Ruban Vibre Beaucoup Cause probableProblème LES Lames Cassent Cause probable Problème LA Lame NE S’ALIGNE PAS Cause probableGarder LA Machine Propre EntretienLames DE Scie À Lame Ruban Démarrage ImpossibleGarantie AccessoiriesRemplacement Gratuit DE Létiquette Entretien ET RéparationInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESProposición DE California Normas Generales DE Seguridad EL USO DE Esta HerramientaGuarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Cordones DE Extensión Fig. D1Prefacio Descripción FuncionalContenido DE Carton Desempaquetado Y LimpiezaPiezas Cerradas DEL Soporte DEL Modelo Base Tornillo de cabeza troncocónica M5 x 0.8 x 10 mm LadoPiezas Abiertas DEL Soporte DEL Modelo Estimación DEL Tiempo DE Ensamblaje EnsamblajeHerramientas DE Ensamblaje Requeridas Montaje DE LA Base DE Soporte Cerrada ModeloNota Apriete libremente el hardware para el ajuste adicional Montaje DE LA Base DE Soporte Abierta Modelo Sobre una superficie planaPage Sujeción DE LA Sierra a LA Base DE Soporte Conectar LA Agujeros DEL Protector DE LA PoleaSujeción DE LA Hoja a LA Sierra Cuerda DEL Motor QUE Conecta a LA Asamblea DE InterruptorSujeción DE LA Mesa a LA Sierra Montaje DE LA Pieza DE Insercion DE MesaBloqueando EL Interruptor EN LA Posicion DE Apagado OperaciónArrancando Y Deteniendo LA Sierra Inclinación DE LA TablaAjuste DE LA Parada DE LA Tabla Ajuste DE LA Tensión DE LA LáminaSeguir LA Lámina Ajuste Vertical DEL Montaje Superior DE LA Guía DE LA LáminaDesconecte la maquina de la fuente de energia Utilizar LA Maquina Puerto DEL PolvoCausa probable Guia Localizacion DE FallasCorte DE Curvas Causa probable RemedioRemedios Hojas DE Sierra DE Cinta Localizacion DE Fallas MantenimientoMantenga LA Máquina Limpia Servicio Accesorios Garantia