DeWalt DW872 manual Additional Specific Safety Rules, Awg

Page 4

392736-01,00,DW872 6/29/00 9:00 AM Page 2

English

to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

 

 

 

 

Volts

 

Minimum Gage for Cord Sets

 

 

 

 

Total Length of Cord in Feet

101-150

 

120V

 

0-25

26-50

51-100

 

240V

 

0-50

51-100

101-200

201-300

 

Ampere Rating

 

AWG

 

 

 

More

 

Not more

 

 

 

 

Than

 

Than

 

 

 

 

 

0 -

6

18

16

16

14

 

6 -

10

18

16

14

12

 

10-

12

16

16

14

12

 

 

12-

16

14

12

Not Recommended

WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.

SECURE WORK. Use clamps, including supplied auxiliary vertical clamp and/or a vise to hold work. It’s safer than using your hand.

DON’T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.

USE RECOMMENDED ACCESSORIES. Consult the instruction

2

manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped over or if the cutting tool is unintentionally contacted.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function — check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

REPLACEMENT PARTS. When servicing use only identical replacement parts.

TO REDUCE THE RISK OF ELECTRIC SHOCK, this equipment has a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit, contact a qualified electrician to install the proper outlet. DO NOT CHANGE THE PLUG IN ANY WAY.

Additional Specific Safety Rules

BE SURE THE BLADE BOLT IS TIGHTENED SECURELY BEFORE CUTTING.

Wear eye protection.

Keep hands out of path of saw blade. Never cut a piece where hand would be 6" (152 mm) or less from blade.

Do not operate saw without guards in place.

Do not perform any operation freehand.

Never reach in back of saw blade.

Turn off tool and wait for saw blade to stop before moving workpiece or changing settings.

Disconnect power before changing blade or servicing.

No Load speed of this tool is 1300 rpm.

Always position tool on a flat, stable surface before use.

Image 4
Contents 392736-01,00,DW872 6/29/00 900 AM DW872 Important Safety Instructions Polarized Plugs DewaltAdditional Specific Safety Rules AWGCutting Capacity Power SupplyMaximum Cutting Capacity Installation of Blade Unplug Unit from Power SUPPLY. FIGStandard Equipment To Carry FigAuto Retracting Guard Fig Fence Angle Adjustment Fig Disconnect the Power SupplyVise Operation Fig Fence Operation FigAuxiliary Vertical Clamp Fig Chip Deflector Adjustment FigMaterial Positioning and Clamping Tips , 11 Switch Fig Cutting Process ChecklistProcedure For Permanent Mounting Fig Good Care/Cutting PracticesMaintenance Motor Brush Inspection and Replacement Fig CleaningAccessories Full WarrantyWHAT’S WRONG? What to DO… Importantes consignes de sécurité Fiches polariséesAutres règles de sécurité · NE Jamais Couper DE Magnésium Avec CET Outil Installation de la lame et Alimentation electriqueCapacité de coupe Équipement standardFonctionnement de l’étau Fig Carter autorétractable FigBien EN Place SUR LE Boulon Avant DE Couper Fonctionnement du guide Fig Réglage de l’angle du guide FigRéglage du déflecteur de copeaux Fig Serre-joint auxiliaire FigBons usages de coupe Interrupteur FigPièce DE Travail Lors DU Démarrage DE Loutil Maintenance AccessoiresProcédure pour le montage permanent Fig Montage du supportGarantie complète LubrificationGarantie DE Satisfaction DE 30 Jours Guide de dépannage Importantes Instrucciones de Seguridad Enchufes polarizadosCalibre promedio del alambre Normas de seguridad específicas adicionales · REPUESTOS. Utilice solamente piezas de repuesto idénticasFuente de energía Capacidad de corteCapacidad máxima de corte Equipos estándarPara transportar la herramienta Fig Para quitarle el seguro FigInstalación de la hoja y Protección auto-retractable FigOperación del Cerco Fig Operación del torno de banco FigAjustes al ángulo del cerco Fig Abrazadera auxiliar vertical Fig Ajuste del deflector de astillas FigDesconecte LA Fuente DE Energía Interruptor Fig Buen cuidado/ Prácticas de corte Instrucciones para montaje permanente FigPieza DE Trabajo Cuando SE Enciende LA Herramienta SIN Excepción AlgunaInstalación del soporte MantenimientoLimpieza AccesoriosGarantía DE Satisfacción SIN Riesgo 30 Días QUE PASA?