DeWalt DW872 manual Auto Retracting Guard Fig

Page 7

392736-01,00,DW872 6/29/00 9:00 AM Page 5

FIG. 7

D

 

B

E

 

C

A

FIG. 8

A

FIG. 9

A

 

B

5

the hex wrench rotate the bolt cover (B) out of the way and loosen the bolt (C) counterclockwise. Then remove the bolt (C), lock washer (D), the flat washer (E) and the outer clamp washer (F).

4.Install blade (G) oriented as shown against the inner clamp washer (H). Reassemble the outer clamp washer, flat washer, lock washer and bolt hand tight.

5.With blade lock engaged, tighten the bolt securely with the hex wrench.

6.Remove hex wrench then release lower guard and blade lock lever.

7.Use same steps to remove the blade.

DO NOT MAKE ANY ADJUSTMENT WHILE TOOL IS PLUGGED INTO POWER SUPPLY.

WARNING: VISUALLY CHECK BLADE FOR CRACKS OR OTHER DAMAGE. VERIFY PROPER BLADE INSTALLATION BEFORE USE. IF BLADE IS DAMAGED IN ANY WAY, HAVE IT RECONDITIONED AT A QUALIFIED SAW BLADE SERVICE SHOP.

WARNING: BE SURE THE BLADE BOLT IS TIGHTENED SECURELY AND THE BOLT COVER IS COVERING THE BOLT HEAD BEFORE CUTTING.

Auto Retracting Guard (Fig. 5)

This tool has an automatic retracting lower guard system. The blade is exposed as it approaches the material and is covered in the up position.

When cutting very large pieces, it may be necessary to manually assist the guard in retracting. To accomplish this, rotate the guard

(A)slightly by the lip (B), just enough to clear the workpiece and release.

Keep hands and other body parts away from rotating blade.

Do not remove blade guard system.

Keep guard system in good operating condition.

English

Image 7
Contents 392736-01,00,DW872 6/29/00 900 AM DW872 Dewalt Important Safety Instructions Polarized PlugsAWG Additional Specific Safety RulesCutting Capacity Power SupplyMaximum Cutting Capacity To Carry Fig Installation of BladeUnplug Unit from Power SUPPLY. FIG Standard EquipmentAuto Retracting Guard Fig Fence Operation Fig Fence Angle Adjustment FigDisconnect the Power Supply Vise Operation FigAuxiliary Vertical Clamp Fig Chip Deflector Adjustment FigMaterial Positioning and Clamping Tips , 11 Good Care/Cutting Practices Switch FigCutting Process Checklist Procedure For Permanent Mounting FigFull Warranty Maintenance Motor Brush Inspection and Replacement FigCleaning AccessoriesWHAT’S WRONG? What to DO… Fiches polarisées Importantes consignes de sécuritéAutres règles de sécurité · NE Jamais Couper DE Magnésium Avec CET Outil Équipement standard Installation de la lame etAlimentation electrique Capacité de coupeFonctionnement de l’étau Fig Carter autorétractable FigBien EN Place SUR LE Boulon Avant DE Couper Réglage de l’angle du guide Fig Fonctionnement du guide FigSerre-joint auxiliaire Fig Réglage du déflecteur de copeaux FigBons usages de coupe Interrupteur FigPièce DE Travail Lors DU Démarrage DE Loutil Montage du support MaintenanceAccessoires Procédure pour le montage permanent FigGarantie complète LubrificationGarantie DE Satisfaction DE 30 Jours Guide de dépannage Enchufes polarizados Importantes Instrucciones de SeguridadCalibre promedio del alambre · REPUESTOS. Utilice solamente piezas de repuesto idénticas Normas de seguridad específicas adicionalesEquipos estándar Fuente de energíaCapacidad de corte Capacidad máxima de corteProtección auto-retractable Fig Para transportar la herramienta FigPara quitarle el seguro Fig Instalación de la hoja yOperación del Cerco Fig Operación del torno de banco FigAjustes al ángulo del cerco Fig Abrazadera auxiliar vertical Fig Ajuste del deflector de astillas FigDesconecte LA Fuente DE Energía Interruptor Fig SIN Excepción Alguna Buen cuidado/ Prácticas de corteInstrucciones para montaje permanente Fig Pieza DE Trabajo Cuando SE Enciende LA HerramientaAccesorios Instalación del soporteMantenimiento LimpiezaGarantía DE Satisfacción SIN Riesgo 30 Días QUE PASA?