DeWalt DW716XPS instruction manual Maintenance

Page 16

English

WARNING: Ensure the saw is mounted firmly to a stable flat surface. Failure to do so could cause the saw to be unstable and fall causing personal injury.

4.Place the workpiece to be cut on top of the platform mounted to the table. Ensure the workpiece is firmly against the backfence (Fig. 22).

5.Secure the material before cutting. Cut slowly through the material. Failure to clamp securely or cut slowly could

result in the material coming loose and causing injury. After several cuts are made at various miter angles other than 0º, the platform may weaken and not properly support the work. Install a new, unused platform to the saw after presetting the desired miter angle.

CAUTION: Continued use of a platform with several kerfs may cause loss of material control and possible injury.

Removing and Replacing Belt

The belt is designed to last the life of the tool. However, abuse of the tool could cause the belt to fail.

If the blade does not turn when the motor is running, the belt has failed. To inspect or replace the belt, remove the belt cover screws. Remove the belt cover. Inspect the ribs of the belt for wear or failure. Check belt tension by squeezing the belt as shown in Figure 23. The belt halves should almost touch when squeezing firmly with the thumb and index finger. To adjust the tension, loosen, but do not remove, the four Phillips head screws shown. Then rotate the set screw on the top of the motor plate casting until the proper tension is achieved. Tighten the four screws securely and replace the belt cover.

NOTE: Over tightening the belt will cause premature motor failure.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic guard. The polycarbonate material used in the guard is subject to attack by certain chemicals.

1.All bearings are sealed. They are lubricated for life and need no further maintenance.

2.Periodically clean all dust and wood chips from around AND UNDER the base and the rotary table. Even though slots are provided to allow debris to pass through, some dust will accumulate.

3.The brushes are designed to give you several years of use. If they ever need replacement follow the instructions under Brushes or return the tool to the nearest service center for repair.

FIG. 21

FIG. 22

SCREWS (two each side)

 

SET

FIG. 23

SCREW

 

SCREWS

Worklight Cleaning

For the best worklight performance, perform the following maintenance regularly.

Carefully clean sawdust and debris from worklight lens with a cotton swab.

DO NOT use solvents of any kind, they may damage the lens.

Dust build-up can block the worklight and prevent it from accurately indicating the line of cut.

Follow miter saw’s instruction manual to remove and install blade.

With blade removed from saw, clean pitch and build- up from blade. Pitch and debris can interfere with the worklight and prevent it from accurately indicating the line of cut.

Service Information

Please have the following information available for all service calls:

Model Number _________________________ Type ______

Serial Number ______________________________________

Date and Place of Purchase __________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:

WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product.

CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase.

FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt. com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This

14

Image 16
Contents Dewalt Page Definitions Safety Guidelines Safety Instructions For All ToolsDouble Insulation Polarized PlugsAdditional Safety Rules For Miter Saws Electrical Connection AccessoriesOn Base 2 Places Important Safety Instructions Specifications Optional Accessories FigUnpacking Your Saw Blade DescriptionsFamiliarization DriveVolt Motor DW716Assembly and Adjustments Changing or Installing a New Saw Blade FigInstalling a Blade Bench MountingAdjustments Transporting the SawBrushes Fig ControlsOperation To Install Clamp Sold Separately Body and Hand Position FIGClamping the Workpiece Proper CUT Improper CUT Support for Long PiecesWhen Mitering to the Right Cutting Trim Molding and Other FramesExamples Cutting Compound MitersWhen Mitering to the Left Bevel Setting Type of CUTCutting Base Molding Cutting Base Molding UP to 6 152 MMSpecial Cuts Maintenance Year Free Service Troubleshooting GuideDAY Money Back Guarantee Compound Miter CUT Directives DE Sécurité Importantes Conserver Tous LES Avertissements ET ToutesNon recommandé Règles de sécurité supplémentaires pour les scies à onglets15,2 30,5 100 45,7 150 30,5 100 61,0 200 91,4 300Français Accessoires Accessoires facultatifs FigConnexion électrique SUR LE PARE-MAINDésemballage de la scie Fiche techniqueFamiliarisation Assemblage ET AjustementsDépose de la lame Changement ou pose d’une Nouvelle lame de scie FigCoup sûr au fonctionnement adéquat de la scie Transport de la scie RéglagesPose d’une lame Réglage D’ÉCHELLE À Onglets FIGRéglage DU Pointeur D’ONGLET Réglage DU Biseau EN Équerre Avec LA Table FIGPointeur DE Biseau FIG Réglage DE LA Butée DU Biseau À 33,9 FIGCommandes Balais FigFonctionnement Installation DE LA Bride Vendu Séparément Fixation DE LA PièceSoutien DES Pièces Longues Coupe Adéquate Coupe InadéquateDécoupe DE Moulures DE Garnissage ET D’AUTRES Cadres ExemplesPAS DE Côté Onglet OU Biseau D’ANGLE Coupe À Onglets MixtesPour L’ASSEMBLAGE EN Onglet À Droite Pour L’ASSEMBLAGE EN Onglet À GaucheDécoupe DE Moulures D’EMBASE LA VERTICALE, Contre LE GuideDécoupes spéciales Découpe D’ALUMINIUMMatériau Arqué Découpe DE Tuyau EN Plastique OU D’AUTRE Matériau RondConfiguration Spéciale Pour LES Coupes Transversales Larges Dépose et remplacement de la courroieCoupe DE Grands Matériaux Entretien Guide de dépannage Tableau 1 Coupe À Onglet Mixte Réglez CET Angle DE Biseau SUR LA ScieDefiniciones Normas de seguridad Instrucciones DE Seguridad ImportantesDoble aislamiento Enchufes polarizadosDesde Hasta En amperiosNo recomendado Español Accesorios Conexión eléctricaAccesorios opcionales Fig Instrucciones DE Seguridad Importantes Desembalar la sierra EspecificacionesFamiliarizarse con la herramienta Montaje Y AjustesRetiro de la hoja Cambio o instalación de una hoja de sierra nueva FigAtención Instalación de la hoja Transporte de la sierraAjustes AdvertenciaRegulación DEL Indicador DE Inglete Bisel a Escuadra CON LA Mesa FIGIndicador DE Bisel FIG Cómo Ajustar EL Tope DEL Bisel a 33,9 FIGCepillos Fig ControlesOperación Sujeción DE LA Pieza DE Trabajo Para Instalar LA Abrazadera SE Vende POR SeparadoSoporte DE Piezas Largas Siempre Utilice Soportes Para LAS Piezas LargasCorte DE Molduras DE Terminación Y Otros Marcos EjemplosCorte DE Ingletes Compuestos Escala VernierConfiguración Tipo DE Corte DE Bisel Inglete a LA DerechaInglete a LA Izquierda Corte DE Molduras DE BaseCortes especiales Corte DE AluminioMaterial Curvado Cortes DE Tuberías DE Plástico U Otros Materiales RedondosConfiguración Especial Para Cortes Transversales Anchos Retiro y reemplazo de la correaMantenimiento Limpieza de la luz de trabajoInformación sobre servicio ReparacionesRegistro en línea Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoGuía para solucionar problemas Fije Este Ángulo DE Bisel EN LA Sierra Tabla 1 Corte DE Inglete CompuestoÁngulo DEL Lado DE LA Caja Ángulo a Copyright 2005, 2008, 2009, 2012, 2014 D Ewalt