DeWalt DW716XPS instruction manual Electrical Connection, Accessories, On Base 2 Places

Page 5

NEVER cross arms in front of blade while using tool. Always make a dry run (unpowered) before making a finish cut so that you can check the path of the blade or severe personal injury may result.

ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

WARNING: Do not connect unit to electrical power source until complete instructions are read and understood.

WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

For your convenience and safety, the following warning labels are on your miter saw.

ON MOTOR HOUSING:

WARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL BEFORE OPERATING MITER SAW.

WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS. ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION.

ON MOVING FENCES:

ALWAYS ADJUST FENCE PROPERLY BEFORE USE. CLAMP SMALL PIECES BEFORE CUTTING. SEE MANUAL.

ON GUARD:

DANGER --KEEP AWAY FROM BLADE.

ON UPPER GUARD:

PROPERLY SECURE BRACKET WITH BOTH SCREWS

BEFORE USE.

ON TABLE: (2 PLACES)

WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING MITER SAW. KEEP HANDS

OUT OF PATH OF SAW BLADE. DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE. CHECK LOWER GUARD FOR PROPER CLOSING BEFORE EACH USE. ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE. DO NOT PERFORM ANY OPERATION FREEHAND. NEVER REACH IN BACK OF SAW BLADE. NEVER CROSS ARMS IN FRONT OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO STOP BEFORE MOVING WORKPIECE, CHANGING SETTINGS OR MOVING HANDS. DISCONNECT POWER BEFORE CHANGING BLADE OR SERVICING. TO REDUCE THE RISK OF INJURY, RETURN CARRIAGE TO THE FULL REAR POSITION AFTER EACH CROSSCUT OPERATION. THINK! YOU CAN PREVENT ACCIDENTS.

ON BASE: (2 PLACES)

Electrical Connection

Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that your saw will operate on alternating current. The switch is susceptible to failure if direct current is used. A voltage decrease of 10 percent or more will cause a loss of power and overheating. All DEWALT tools are factory tested. If this tool does not operate, check the power supply.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product.

Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.

English

3

Image 5
Contents Dewalt Page Safety Instructions For All Tools Definitions Safety GuidelinesDouble Insulation Polarized PlugsAdditional Safety Rules For Miter Saws On Base 2 Places AccessoriesElectrical Connection Specifications Optional Accessories Fig Important Safety InstructionsUnpacking Your Saw Blade DescriptionsDrive FamiliarizationVolt Motor DW716Changing or Installing a New Saw Blade Fig Assembly and AdjustmentsInstalling a Blade Bench MountingTransporting the Saw AdjustmentsControls Brushes FigOperation Body and Hand Position FIG To Install Clamp Sold SeparatelyClamping the Workpiece Proper CUT Improper CUT Support for Long PiecesCutting Trim Molding and Other Frames When Mitering to the RightExamples Cutting Compound MitersBevel Setting Type of CUT When Mitering to the LeftCutting Base Molding Cutting Base Molding UP to 6 152 MMSpecial Cuts Maintenance DAY Money Back Guarantee Troubleshooting GuideYear Free Service Compound Miter CUT Conserver Tous LES Avertissements ET Toutes Directives DE Sécurité ImportantesRègles de sécurité supplémentaires pour les scies à onglets Non recommandé15,2 30,5 100 45,7 150 30,5 100 61,0 200 91,4 300Français Accessoires facultatifs Fig AccessoiresConnexion électrique SUR LE PARE-MAINFiche technique Désemballage de la scieFamiliarisation Assemblage ET AjustementsCoup sûr au fonctionnement adéquat de la scie Changement ou pose d’une Nouvelle lame de scie FigDépose de la lame Réglages Transport de la sciePose d’une lame Réglage D’ÉCHELLE À Onglets FIGRéglage DU Biseau EN Équerre Avec LA Table FIG Réglage DU Pointeur D’ONGLETPointeur DE Biseau FIG Réglage DE LA Butée DU Biseau À 33,9 FIGBalais Fig CommandesFonctionnement Fixation DE LA Pièce Installation DE LA Bride Vendu SéparémentSoutien DES Pièces Longues Coupe Adéquate Coupe InadéquateExemples Découpe DE Moulures DE Garnissage ET D’AUTRES CadresPAS DE Côté Onglet OU Biseau D’ANGLE Coupe À Onglets MixtesPour L’ASSEMBLAGE EN Onglet À Gauche Pour L’ASSEMBLAGE EN Onglet À DroiteDécoupe DE Moulures D’EMBASE LA VERTICALE, Contre LE GuideDécoupe D’ALUMINIUM Découpes spécialesMatériau Arqué Découpe DE Tuyau EN Plastique OU D’AUTRE Matériau RondCoupe DE Grands Matériaux Dépose et remplacement de la courroieConfiguration Spéciale Pour LES Coupes Transversales Larges Entretien Guide de dépannage Réglez CET Angle DE Biseau SUR LA Scie Tableau 1 Coupe À Onglet MixteInstrucciones DE Seguridad Importantes Definiciones Normas de seguridadDoble aislamiento Enchufes polarizadosNo recomendado En amperiosDesde Hasta Español Accesorios opcionales Fig Conexión eléctricaAccesorios Especificaciones Instrucciones DE Seguridad Importantes Desembalar la sierraFamiliarizarse con la herramienta Montaje Y AjustesAtención Cambio o instalación de una hoja de sierra nueva FigRetiro de la hoja Transporte de la sierra Instalación de la hojaAjustes AdvertenciaBisel a Escuadra CON LA Mesa FIG Regulación DEL Indicador DE IngleteIndicador DE Bisel FIG Cómo Ajustar EL Tope DEL Bisel a 33,9 FIGControles Cepillos FigOperación Para Instalar LA Abrazadera SE Vende POR Separado Sujeción DE LA Pieza DE TrabajoSoporte DE Piezas Largas Siempre Utilice Soportes Para LAS Piezas LargasEjemplos Corte DE Molduras DE Terminación Y Otros MarcosCorte DE Ingletes Compuestos Escala VernierInglete a LA Derecha Configuración Tipo DE Corte DE BiselInglete a LA Izquierda Corte DE Molduras DE BaseCorte DE Aluminio Cortes especialesMaterial Curvado Cortes DE Tuberías DE Plástico U Otros Materiales RedondosRetiro y reemplazo de la correa Configuración Especial Para Cortes Transversales AnchosLimpieza de la luz de trabajo MantenimientoInformación sobre servicio ReparacionesGarantía limitada por tres años Registro en líneaExcepciones AÑO DE Servicio GratuitoGuía para solucionar problemas Ángulo DEL Lado DE LA Caja Ángulo a Tabla 1 Corte DE Inglete CompuestoFije Este Ángulo DE Bisel EN LA Sierra Copyright 2005, 2008, 2009, 2012, 2014 D Ewalt