Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in selecting and using accessories.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled. Your saw table is designed to accept two work supports; one on each side.
Adjustable Length Stop: DW7051
Requires the use of one work support. It is used to make repetitive cuts of the same length from 0 to 42" (1.06 m).
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precision cutting.
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Laser Guide System: DW7187
Powered by the saw, the bright laser line delivers enhanced visibility in low and high light locations. Easy to install.
Miter Saw Replacement Kerf Plate: DW7055
This durable plastic uncut plate limits blade tear out.
SAW BLADES: ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diam- eter blade. It will not be guarded properly. Use crosscut blades only! Do not use blades designed for ripping, combination blades or blades with hook angles in excess of 5˚.
DEWALT BLADE | NO. OF | BLADE DESC. | APPLICATION | TYPE OF CUT | |
RANGE | TEETH | ||||
|
|
| |||
Series 20 |
| Thin Kerf | Gen. Purpose | Smooth, | |
40 | (Trim, Decking, | ||||
Construction | Yellow Rim Coating | Splinter Free | |||
| Framing) | ||||
|
|
|
| ||
Series 20 | 60 | Thin Kerf | Fine Trim Molding | Very Smooth, | |
Construction | Yellow Rim Coating | Splinter Free | |||
Series 40 |
| Laser Cut Body | Gen. Purpose | Smooth, Splinter | |
40 | Large Carbide | (Trim, Decking, | |||
Woodworking | Free | ||||
| Teeth | Framing) | |||
|
|
| |||
Series 40 |
| Laser Cut Body | Fine Trim, | Very Smooth, | |
60 | Large Carbide | ||||
Woodworking | Molding | Splinter Free | |||
| Teeth | ||||
|
|
|
| ||
|
| Laser Cut Body | Fine Trim Molding |
| |
Series 40 |
| Decorative | Ultra Smooth, | ||
80 | Large Carbide | ||||
Woodworking | Hardwood & | Splinter Free | |||
| Teeth | ||||
|
| Plywood |
| ||
|
|
|
| ||
|
| Laser Cut Body | Melamines, | Ultra Smooth | |
Series 40 |
| Large Carbide | |||
80 | Veneers, | Chip/Splinter | |||
Woodworking | Teeth, Special | ||||
| Laminates | Free | |||
|
| Tooth Geometry | |||
|
|
|
| ||
Series 40 |
| Laser Cut Body | Plastics and other | Very Smooth | |
60 | Special Tooth | solid surface | |||
Woodworking | Chip Free | ||||
| Geometry | materials | |||
|
|
| |||
|
| Laser Cut Body |
| ||
Series 40 |
| metals (aluminum, | Very Smooth | ||
80 | Special Tooth | ||||
Woodworking | copper, brass, | Burr Free | |||
| Geometry | ||||
|
| etc.) |
| ||
|
|
|
|
4
DW7082
DW7080
LOCKNUTS
END PLATE
DW7051
DW7084
TOP HOLE (USE IF ON LEFT SIDE)
KNOBS
BOTTOM HOLE
(USE IF ON
RIGHT SIDE)
BRACKET
DW7187