DeWalt DW713 instruction manual Installing a Blade, Transporting the Saw, Adjustments

Page 7

FIG. 4

FIG. 5

OUTER

FIG. 6

CLAMP

WASHER

BLADE

SCREW

LOCK

DOWN

PIN

GUARD

GUARD

BRACKET

SCREW

WRENCH

BLADE

BLADE

ADAPTER

INNER CLAMP

WASHER

5.Keeping the button depressed, use the other hand and the wrench provided to loosen the blade screw. (Turn clockwise, left-hand threads)

6.Remove the blade screw, outer clamp washer, and blade. The 1" (25.4 mm) blade adapter, if used, and the inner clamp washer, may be left on the spindle.

NOTE: For blades with a blade hole of 5/8" (15.88 mm), the 1" (25.4 mm) blade adapter is not used.

Installing a Blade

1.Unplug the saw.

2.With the arm raised, the lower guard held open and the pivot plate raised, place the blade on the spindle, onto the blade adapter [if using a blade with a 1" (25.4 mm) diameter blade hole] and against the inner clamp washer with the teeth at the bottom of the blade pointing toward the back of the saw.

3.Assemble the outer clamp washer onto the spindle.

4.Install the blade screw and, engaging the spindle lock, tighten the screw firmly with wrench provided. (Turn counterclockwise, left-hand threads)

NOTE: When using blades with a 5/8" (15.88 mm) diam- eter blade hole, the blade adapter will not be used and should be stored in a safe place for future use.

5.Return the guard bracket to its original position and firmly tighten the guard bracket screw to hold bracket in place.

WARNING:

•The guard bracket must be returned to its original position and the screw tightened before activating the saw.

•Failure to do so may allow the guard to contact the spinning saw blade resulting in damage to the saw and severe personal injury.

Transporting the Saw

WARNING: Turn off tool and disconnect from power source before attempting to move it, changing acces- sories or making any adjustments accept as written in laser adjustment instructions.

In order to conveniently carry the miter saw from place to place, a carrying handle has been included on the top of the saw arm, as shown in Figure 3. To transport the saw, lower the arm and depress the lock down pin shown in Figure 4.

Adjustments

WARNING: Turn off tool and disconnect from power source before attempting to move it, changing acces- sories or making any adjustments accept as written in laser adjustment instructions.

NOTE: Your miter saw is fully and accurately adjusted at the factory at the time of manufacture. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw.

Once made, these adjustments should remain accurate. Take a little time now to follow these directions carefully to maintain the accuracy of which your saw is capable.

MITER SCALE ADJUSTMENT

Place a square against the saw’s fence and blade, as shown in Figure 7. (Do not touch the tips of the blade teeth with the square. To do so will cause an inaccurate mea- surement.) Unlock miter lock lever (see Fig. 8) and swing the miter arm until the miter detent locks it at the 0˚ miter position. Do not lock miter lock lever. If the saw blade is not exactly perpendicular to the fence, loosen the three screws that hold the miter scale to the base (shown in Fig. 8) and move the scale/miter arm assembly left or right until the blade is perpendicular to the fence, as measured with the square. Retighten the three screws. Pay no attention to the reading of the miter pointer at this point.

MITER POINTER ADJUSTMENT

Unlock miter lock lever and squeeze the miter detent to move the miter arm to the zero position, as shown in Figure 8. Unlock the miter lock lever to allow the miter detent to snap into place as you rotate the miter arm past zero. Observe the pointer and miter scale through the viewing opening shown in Figure 9. If the pointer does not indicate exactly zero, loosen the pointer screw, adjust the pointer to 0˚ and retighten.

BEVEL SQUARE TO TABLE

To align the blade square to the rotary table, lock the arm in the down position. Place a square against the blade taking care to not have the square on top of a tooth, as shown in Figure 10B. Loosen the Bevel Clamp Knob so that you can move the Bevel Arm. Move the Bevel Arm as necessary so that the blade is at 0° bevel to the table. If the Bevel Arm needs adjustment, loosen the lock nut on the right side Bevel Stop as shown in Figure 11, and adjust the stop screw as necessary. Hold the stop screw in place and tighten the lock nut.

BEVEL POINTER

If the bevel pointer does not indicate zero, loosen the screw that holds it in place and move the pointer as necessary. SUGGESTION: For accuracy, set the top edge so that it aligns with zero.

BEVEL STOP

To set the 45° bevel stop shown in Figure 12, first loosen the left side fence clamping knob and slide the left side fence as far as it will go to the left. Move the arm to the left until it stops on the left bevel stop screw. If the bevel pointer does not indicate exactly 45°, loosen the left side bevel stop lock nut and turn the screw downwards. Move the arm to the left and tighten the bevel clamp knob firmly when the bevel pointer indicates exactly 45°. Adjust the left side bevel stop screw upwards until it firmly touches the bevel stop. Retighten the nut while holding the screw from turning.

English

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Page Double Insulation Definitions Safety GuidelinesImportant Safety Instructions Safety Instructions For All ToolsAdditional Safety Rules For Miter Saws Familiarization SpecificationsElectrical Connection Unpacking Your SawOptional Accessories Bench Mounting AccessoriesImportant Safety Instructions Changing or Installing a New Saw BladeAdjustments Installing a BladeTransporting the Saw Guard Actuation and Visibility Fence AdjustmentAutomatic Electric Brake Operation BrushesClamping the Workpiece Body and Hand Position FIGMiter Scale Support for Long Pieces Always Support Long PiecesCutting Trim Molding and Other Frames Cutting Compound MitersCutting Base Molding UP to 3.5 88.9 MM When Mitering to the RightWhen Mitering to the Left Cutting Base MoldingCutting Crown Molding Bevel Setting Type of CUTCutting Large Material Special CutsBowed Material Cutting Plastic Pipe or Other Round MaterialRepairs MaintenanceService Information Troubleshooting GuideSET this Bevel Angle on SAW Setting Degree Miter Bevel Degree SettingBOX Angle a AngleLEA Todas LAS Instrucciones 10A 12A 16A No recomendado Ténsion Volts Longitud del cable in metros m120 127V 220 240V Corriente nominal Sección nominal mínima del cableConexión eléctrica Capacidad DE Corte Desembalar la sierraFamiliarizarse con la herramienta EspecificacionesInstrucciones DE Seguridad Importantes Accesorios opcionalesAccesorios Montaje en el banco de trabajoInstalación de la hoja Retiro de la hojaDesenchufe la sierra Ajustes Transporte de la sierraFreno Eléctrico Automático Accionamiento Y Visibilidad DE LA GuardaRegulación DEL Bloqueo DE Inglete FIG Funcionamiento CepillosPosición DEL Cuerpo Y LAS Manos FIG Calidad DEL CorteSujeción DE LA Pieza DE Trabajo Marcos Soporte DE Piezas LargasSiempre Utilice Soportes Para LAS Piezas Largas Corte DE Molduras DE Terminación Y OtrosInglete a LA Izquierda Escala DE IngleteEscala Vernier Inglete a LA DerechaHacer Pruebas CON Material DE Descarte ES MUY Importante Esquina InteriorEsquina Externa Corte DE Molduras DE CoronaLado Izquierdo Esquina Interior DEL LadoDerecho Esquina EXTERIOR, DELReparaciones Cortes especialesMantenimiento Información del servicio técnicoGuía de detección de problemas Fije Este Ángulo DE Bisel EN LA Sierra SierraDEL Regulación DEL Ángulo DE BiselPlugues polarizados Definições Diretrizes de SegurançaInstruções de segurança importantes Isolamento duplo10A 12A 16A Não Recomendado Regras de segurança adicionais para serras de esquadriaTensão Comprimento do cabo de extensão Faixa de CorrenteSobre a Guardasuperior Conexões elétricasSobre O Compartimento do Motor Sobre a Grade MóvelAcessórios opcionais Desembalando a serraFamiliarização EspecificaçõesTrocando ou instalando uma lâmina de serra nova e AcessóriosMontagem na bancada Instruções DE Segurança ImportantesTransportando a serra Instalando uma lâminaIndicador do Chanfro Ajuste DA Escala DA EsquadriaAjuste do Indicador DA Esquadria Chanfro EM Ângulo Reto COM a MesaFreio Elétrico Automático EscovasAjuste DA Grade Atuação E Visibilidade DA ProteçãoOperação Suporte Para Peças Longas Prendendo a Peça DE TrabalhoSempre USE Suporte Para Peças Longas Escala DA Esquadria Cortando Esquadrias CompostasEscaladevernier E Corte DE 3,5 88,9 mm- 4,25 107,95 mm DE AO Esquadrar Para a DireitaAO Esquadrar Para a Esquerda Corte DE Entalhe BásicoLado DIREITO, Canto Interno Corte DE Entalhe EM RelevoAjuste do Tipo DE Corte Chanfro Lado ESQUERDO, Canto InternoDurante o corte. Posicione o material para que você corte Cortes especiaisLado DIREITO, Canto Externo Corte EM AlumínioMaterial Curvo ManutençãoInformações de serviço ReparosGuia de solução de problemas Ajuste Este Ângulo do Chanfro NA Serra Page DW713
Related manuals
Manual 58 pages 27.02 Kb
Top Page Image Contents