Bosch Power Tools CSW41 Assembly, Spring Auxiliary Handle Upper Guard, SAW Shaft, Inner Washer

Page 9

! WARNING

BM 1619X08893 09-13_BM 1619X08893 09-13.qxp 8/29/13 9:04 AM Page 9

Assembly

ATTACHING THE BLADE Disconnect the plug from the power source before

making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

1. Press the lock button and turn wrench until lock button engages. Saw shaft is now locked. Continue to depress button, turn wrench clockwise and remove BLADE STUD and OUTER WASHER (Fig. 2).

2. Make sure the saw teeth and arrow on the blade point in the same direction as the arrow on the lower guard.

3. Retract the lower guard all the way up into the upper guard. While retracting the lower guard, check operation and condition of the

LOWER GUARD SPRING.

4. Slide blade through slot in the foot and mount it against the INNER WASHER on the shaft. Be sure the large diameter of the INNER and OUTER washers lay flush against the blade.

5.Reinstall OUTER WASHER. First tighten BLADE STUD finger tight, then TIGHTEN BLADE STUD 1/8 TURN (45˚) WITH THE WRENCH PROVIDED.

Do not use wrenches with longer handles, since it may lead to over tightening of the blade stud.

VARI-TORQUE CLUTCH

This clutching action is provided by the friction of the OUTER WASHER against the BLADE and permits the blade shaft to turn when the blade encounters excessive resistance. When the BLADE STUD is properly tightened (as described in No. 5 of Attaching The Blade), the blade will slip when it encounters excessive resistance, thus reducing saw’s tendency to

KICKBACK.

One setting may not be sufficient for cutting all materials. If excessive blade slippage occurs, tighten the blade stud a fraction of a turn more (less than 1/8 turn). OVERTIGHTENING THE BLADE STUD NULLIFIES THE EFFECTIVE- NESS OF THE CLUTCH.

FIG. 2		LOWER GUARD
		SPRING
	AUXILIARY HANDLE
	UPPER GUARD	/4
		1
		1/2	X
		1/2	1
		3/4	MBER

D	LOWER GUARD
OO

	LIFT LEVER
	SAW SHAFT

INNER WASHER

Large Diameter Faces Blade

LOCK

BUTTON

LOWER

GUARD

BLADE

BLADE

STUD

Tighten

OUTER WASHER Large Diameter

Faces Blade

Loosen

-9-

Image 9

Contents Voir Ver la página Call Toll Free forWork area safety General Power Tool Safety WarningsElectrical safety Personal safetySafety Rules for Circular Saws ServiceCutting procedures Kickback causes and related Lower guard functionVARI-TORQUE Clutch Some dust created by power Additional Safety WarningsName Designation/Explanation SymbolsSymbols Pivot Stud Bevel Adjustment Lever Blade Stud Contour Functional Description and SpecificationsCircular Saws Calibrated Depth BracketSpring Auxiliary Handle Upper Guard AssemblySAW Shaft Inner WasherOperating Instructions SET Screw Wrench Usage Maximum Depth of CUT StabilityWrench Slotted Driver Correct IncorrectGeneral Cuts SwitchCutting MASONRY/METAL Plunge CutsWrong Cutting Large SheetsRight RIP Cuts RIP Board GuideCleaning MaintenancePreventive maintenance Tool LubricationAccessories Extension CordsCare of Blades Trouble Shooting Sécurité électrique Sécurité du lieu de travailUtilisation et entretien des outils Électroportatifs Consignes de sécurité pour scies circulairesEntretien Procédures de coupeEmbrayage VARI-TORQUE Fonction du garde inférieurLe plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesSymboles suite Description fonctionnelle et spécifications Graduée en fonction des dimensions Standard du bois d’œuvreScies circulaires Ressort DE ButéeEmbrayage « VARI-TORQUE » Assemblage’ARBRE DE LA Scie Lame Goujon DE Lame Rondelle ExterieureReglage DE LA Profondeur DE Coupe Consignes d’utilisationLevier DE Reglage DE LA Profondeur FIG Levier DE Réglage DU Biseau Guide D’ALIGNEMENTCLÉ DE 1/2 PO VIS DE Réglage Utilisation DE LA CLÉCLÉ DE 9/16 PO CoinCoupes Regulierès InterrupteurMouvement de la garde inférieure Sciage DES Matériaux DE Maçonnerie ET DES MétauxMauvaise Manière Coupe DE Grandes FeuillesBonne Manière Coupes DE Refente Utilisation D’UNE Planche Comme Guide DE RefenteDe l’entretenir EntretienLubrification DE L’OUTIL Balais DE CharbonAccessoires Cordons de rallongeEntretien DES Lames Guide de diagnostic Seguridad del área de trabajo Seguridad eléctricaSeguridad personal Mecánicas Normas de seguridad para sierras circularesServicio de ajustes y reparaciones Procedimientos de corteEmbrague DE PAR Motor Variable RelacionadasFunción del protector inferior Advertencias de seguridad adicionalesSímbolo Nombre Designación/explicación SímbolosSímbolos continuación Sierras circulares Descripción funcional y especificacionesProtector Superior EnsamblajeEJE DE LA Sierra Inferior HojaInstrucciones de funcionamiento DE Corte Máxima Utilización DE LA Llave DE TuercaTuerca Con la orientación Cortes Generales Guía DE InterruptorCorte DE Mampostería Y Metal Cortes POR InmersiónCorrecto Cortes AL Hilo Corte DE Planchas GrandesTABLERO-GUIA Para Cortar AL Hilo Linea DE Corte DeseadaServicio MantenimientoLimpieza Lubricacion DE LAS HerramientasCordones de extensión AccesoriosCuidado DE LAS Hojas Avería LA Sierra no Arranca Resolución de problemasAvería LA Hoja no Alcanza Toda SU Velocidad Avería Vibración ExcesivaRemarques Notas 1619X08893