Black & Decker 90544326, BT1800 manual Assembling Stand, SAW to Stand

Page 41

ASSEMBLING STAND

1.Assemble the stand as shown in Fig. 4C, using 16 M8x1.25x20mm carriage head bolts, 3/8” flat washers and M8x1.25 hex nuts. Align the holes in the stand legs (F) with the holes in the brackets. Insert the carriage head bolt through the hole in the leg and the hole in the bracket, place a flat washer on the carriage head bolt and thread a hex nut onto the carriage head bolt. Repeat this process for the 15 remaining holes in the legs and brackets.

NOTE: Loosely tighten the hardware for further adjustment.

Letters are on the stand brackets to ease assembly:

A - Top front and rear brackets

B - Top side brackets

C - Bottom side brackets

D - Bottom front and rear brackets

2.Attach the rubber feet (E) Fig. 4C to the bottom of each leg (F).

A	B
A
	F
C
	E
D

Fig. 4C

SAW TO STAND

1.Turn saw table face down on a piece of cardboard to protect the table surface. Place stand upside down onto saw and align the four holes in the stand with the mounting holes in the saw.

2.Place a 3/8” flat washer on a M8x1.25x45mm hex head screw. Insert the hex head screw through the mounting hole in the saw and the mounting hole in the stand. Place another 3/8” flat washer on the hex head screw and thread a M8x1.25 hex nut on the screw and loosely tighten. Complete this process for the other three holes.

3.Stand the saw upright, as shown in Fig. 4D (Saw is shown fully assembled here).

4.Push down on top of the saw so that the legs of the stand adjust to the surface of the floor. Tighten all hardware securely.

ASSEMBLING BLADE RAISING AND LOWERING HANDWHEEL

1.Insert special screw (C) through handle (B) Fig.5 and assembly handle to handwheel (A) by threading screw clockwise into handwheel. Then push on handle cover (D).

2.Fig. 6, illustrates the handle (B) assembled to handwheel (A).

3.Assemble handwheel (A) Fig. 7, to shaft (B) making sure the flat on inside of handwheel lines up with flat on shaft.

4.Fasten handwheel (A) Fig. 8, to shaft (B) Fig. 7, using a M6x1x12mm flat head screw (C) Fig. 8.

A

B

Fig. 7

Fig. 4D

A

B

C D

Fig. 5

Fig. 6

C

A

Fig. 8

41

Image 41

Contents 10 254mm Table Saw Normas Generales DE Seguridad No Devuelva Este Producto a LA TiendaConserve Estas Instrucciones Instrucciones DE SeguridadEtiquetas Sobre LA Herramienta Sierras DE MesaServicio Técnico Conexiones Eléctricas Descripción DE LAS FuncionesEspecificaciones DEL Motor IntroducciónPiezas DE LA Sierra Para Banco Contenido DE LA CajaDesconecte LA Máquina DE LA Fuente DE Alimentación MontajeDesembalaje Y Limpieza Colocación DEL Volante Para Ajustar LA Altura DE LA Hoja Montaje DE LA BaseSierra a LA Base Colocación DEL Ensamble DE Guarda DE LA Hoja Y Separador Guía DE Inglete Montaje DE LA Guía DE Corte Colocación DEL Sujetador DE LA Guía DE IngleteControles DE Operación Y Ajustes OperaciónAjustar UN Tope Positivo a 45 Grados Ajustes DE Topes Positivos a 90 Y 45 GradosAjustar UN Tope Positivo a 90 Grados Desconecte LA Máquina DE LA Fuente DE ALIMENTACIÓN.` Ajuste DEL Inserto Para MesaOperación DEL Calibrador DE Inglete Y Ajustes Corte Transversal USO DE LA MáquinaCambio DE LA Hoja Corte Longitudinal Page Construcción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo Para EmpujarInformación DE Servicio Detección DE ProblemasMantenimiento Regras Gerais DE Segurança NÂO Devolva Este Produto NA LojaGuarde Estas Instruções Instruções DE SegurançaRótulos DA Ferramenta Conexões ElétricasEspecificações do Motor Descrição FuncionalInstruções DE Aterramento IntroduçãoPeças DA Serra DE Bancada Motorizada Conteúdos DA CaixaElevando E Apoiando Superfícies Para UMA Serra SEM Base MontagemComo Desembalar E Fazer a Limpeza Fixando O Volante DE Ajuste DE Altura DA Lâmina Montagem DA BaseInstalação DA Serra NA Base Desconecte O Equipamento DA Fonte DE Energia Fixando a Proteção DA Lâmina E O SeparadorGraminho Montagem DA Guia DE Corte Fixando O Prendedor do GraminhoAjuste DE Inclinição DE Lâmina OperaçãoAjuste DA Altura DA Lâmina Ajuste DE Trava Positiva a 90 Graus Ajustes DE Travas Positivas EM Ângulos DE 90 E 45 GrausAjuste DE Trava Positiva a 45 Graus Operação E Ajustes NA Guia DE Corte Y AjustesOperação E Ajustes do Graminho Ajuste do Inserto DE BancadaTrocando a Lâmina USO do EquipamentoCorte Longitudinal Inserto DE Bancada do Conjunto DA Fresa Para Ranhurar Construindo UM Pente Construindo UM Bastão DE EmpurrarInformações DE Serviço Solução DE ProblemasManutenção Do not Return this Product to the Store General Safety RulesSafety Instructions Labels on Tool Additional Safety Rules for Table SawsMotor Specifications Power ConnectionsFunctional Description Grounding InstructionsCarton Contents Unpacking and Cleaning AssemblyDisconnect Machine from Power Source SAW Support Must be Stable and Able to Support 300 PoundsAssembling Blade Raising and Lowering Handwheel Assembling StandSAW to Stand Attaching Blade Guard and Splitter Assembly Miter Gauge Assembling RIP Fence Attaching Miter Gauge HolderLocking Switch in the OFF Position Operational Controls and AdjustmentsBlade Height Adjustment Blade Tilt AdjustmentRIP Fence Operation and Adjustments To Adjust Positive Stop AT 90 DegreesTo Adjust Positive Stop AT 45 Degrees Adjusting Blade Parallel to Miter Gauge Slots Table Insert AdjustmentCROSS-CUTTING Machine USEChanging the Blade Ripping Attach the dado head set D , to the saw arbor Constructing a Featherboard Constructing a Push StickService Information MaintenanceTroubleshooting