Bosch Power Tools 3924B manual Battery/Charger, Battery Care, Battery Disposal

Page 6

 

Safety

 

“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (•) symbol listed

! WARNING

 

BELOW and other safety precautions, may result in serious personal injury.

 

 

Battery/Charger

•Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack, and (3) product using battery.

•Use only the charger which accompanied your product or direct replacement as listed in the catalog or this manual. Do not substitute any other charger. Use only Bosch approved chargers with your product. See Functional Description and Specifications.

•Do not disassemble charger or operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Replace damaged cord or plugs immediately. Incorrect reassembly or damage may result in electric shock or fire.

•Do not recharge battery in damp or wet environment. Do not expose charger to rain or snow. If battery case is cracked or otherwise damaged, do not insert into charger. Battery short or fire may result.

•Charge only Bosch approved rechargeable batteries. See Functional Description and Specifications. Other types of batteries may burst causing personal injury and damage.

•Charge battery pack in temperatures above +40 degrees F (4 degrees C) and below +105 degrees F (41 degrees C). Store tool and battery pack in

locations where temperatures do not go below 40 degrees F (4 degrees C) or will no exceed 120 degrees F (49 degrees C). Allow battery pack to return to room temperature before attempting to charge.This is important to prevent serious damage to the battery cells.

•Battery leakage may occur under extreme usage or temperature conditions. Avoid contact with skin and eyes. The battery liquid is caustic and could cause chemical burns to tissues. If liquid comes in contact with skin, wash quickly with soap and water, then with lemon juice or vinegar. If the liquid contacts your eyes, flush them with water for a minimum of 10 minutes and seek medical attention.

•Place charger on flat non-flammable surfaces and away from flammable materials when re-charging battery pack. The charger and battery pack heat during charging. Carpeting and other heat insulating surfaces block proper air circulation which may cause overheating of the charger and battery pack. If smoke or melting of the case are observed unplug the charger immediately and do not use the battery pack or charger.

•Use of an attachment not recommended or sold by Bosch may result in a risk of fire, electric shock or injury to persons.

Battery Care

!WARNING When batteries are not in tool or charger, keep them away from metal

objects. For example, to protect terminals from shorting DO NOT place batteries in a tool box or pocket with nails, screws, keys, etc. Fire or injury may result.

DO NOT PUT BATTERIES INTO FIRE OR EXPOSE TO HIGH HEAT. They may explode.

Battery Disposal

!WARNING Do not attempt to disassemble the battery or remove any component

projecting from the battery terminals. Fire or injury may result. Prior to disposal, protect exposed terminals with heavy insulating tape to prevent shorting.

Nickel-Cadmium Batteries

If equipped with a nickel-cadmium battery, the battery must be collected, recycled or disposed of in an environmentally sound manner.

“The EPA certified RBRC Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates S-B Power Tool Company is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when

taken out of service in the United States or Canada. The RBRC program provides a convenient alterative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which may be illegal in your area.

Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling and disposal bans/restrictions in your area, or return your batteries to a Skil/Bosch/Dremel Service Center for recycling. S-B Power Tool Company’s involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.”

Nickel-Metal Hydride Batteries

If equipped with a nickel-metal hydride battery, the battery can be disposed of in a municipal solid waste stream.

“SAVE THESE INSTRUCTIONS”

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Read Before Using Leer antes de usarSafety General Safety Rules For Benchtop ToolsSafety Rules for Miter Saws ServiceSafety Guar Battery/Charger Battery CareBattery Disposal Table of Contents Getting To Know Your Miter Saw Arbor LockFor Continuation of English see Sécurité Pour les outils d’établiConsignes de sécurité pour les scies à onglet RéparationBlessures Sécurité Mise au rebut des piles Chargeur de pileEntretien des piles Piles nickel-cadmiumDescription fonctionnelle et spécifications Table des matièresFrein électrique Capacités maximalesFamiliarisez-vous avec votre scie à onglet 13. Gâchette de cran d’arrêt d’onglet Trous pour l’accessoire rallonge/butéeBouton de blocage d’onglet 14. Échelle graduée d’ongletSeguridad eléctrica SeguridadArea de trabajo Seguridad personalPara cortar ingletes ServicioSeguridad Advertencia Personales gravesEliminación de las baterías Batería/cargadorCuidado de las baterías Baterias de niquel-cadmioIndice Freno eléctricoDescripción funcional y especificaciones Familiarización con la sierra para cortar ingletes Escala de ingletes Pomo de fijación de ingleteGatillo del retén de inglete RetenesAssemblage AssemblyTools Needed For Assembly And Alignment Outils nécessaires à l’assemblage et à l’alignementDestornillador Phillips Escuadra de combinación EnsamblajeHerramientas necesarias para el ensamblaje y la alineación Sobre la tabla a loUnpacking and Checking Contents Installation of Miter Lock KnobInstalación del pomo de fijación De inglete Ouverture de l’emballage et Vérification du contenuDesempaquetado y comprobación Del contenido Pièces détachéesRemoval and Installation Blade Cutting Kerf InsertPose et dépose de la lame Instalación y remoción de la hojaMoins que 10 po de diamètre et arbre de 5/8 po Assembling Dust Bag Ensamblaje de la bolsa para polvo Assemblage du sac à poussièreBlade Square to Table Blade AlignmentHoja en ángulo recto con La mesa RéglagesAjustesLame d’équerre par rapport La table Alignement de la lame àAdjustments Blade 45 To The TableGlissière à la Abaissez la tête. Bloquez en place Lame à 45 par rapport La tableHoja a 45 respecto a la mesa Baje el ensamblaje del cabezal. Fíjelo en su sitioBlade Square to Fence Fence AlignmentAlineación del tope-guía Hoja en ángulo recto con el tope-guíaAlignement du guide Apriete los tornillos de casquete hexagonales40-1/2 Indicateur ’onglet VernierExactement 40-1/4Indicador de IngletesUso de la escala Vernier y la escala de ingletes Miter Scale Vernier Indicator Adjustment Crown Molding Detent Adjustment BevelCrown Molding Detent Adjustment Ajuste del indicador Vernier de la Escala de ingletes Graduée d’onglet VernierCouronne biseau Ajuste del retén para moldura de Techo biselInstallation Instalación Esto podría agrietar el pie o dañar la baseMounting Applications Portable Mounting Using ClampsPortable Mounting Using 1x4’s WorkbenchApplications de montage Aplicaciones de montajeBasic Saw Operations Body and Hand PositionCorrect Use Incorrect Use Position du corps et des mains Opérations de base de La scieOperaciones básicas De la sierra Posición del cuerpo y de las manosWorkpiece Support ClampsLong Workpiece Support Support de l’ouvrage Soporte de la pieza de trabajoSwitch Activation Actionnement par interrupteur Activación del interruptorDetent Override Sliding Base/Fence ExtensionCourt-circuitage du cran d’arrêt Sobrecontrol del reténExtensión de la base/tope-guía Deslizante Saw Operations Miter CutFollow these instructions for making your miter cut Coupe à l’onglet Opérations de la scieOperaciones de la Sierra Corte a ingleteBevel Cut Follow these instructions for making your bevel cutCoupe en biseau Corte en biselSiga estas instrucciones para hacer un corte en bisel Compound Cuts Follow these instructions for making your compound cutSuivez ces instructions pour pratiquer votre coupe composée Coupes composéesCortes compuestos Siga estas instrucciones para hacer un corte compuestoBase Molding Corner of wallMoulures de base Le guide ou à plat sur la table Coupe de moulures de baseMoldura de base Cutting Crown Molding Corte de moldura de techoCrown Molding Laying Flat on Table Follow these instructions for cutting crown moldingMoulures en couronne reposant à plat sur la table 33,9Serre-joint DouvrageOnglet de 31,6 Moldura de techo colocada horizontalmente sobre la mesa Maximo 41⁄4Crown Molding Angled to Table Fence Position the molding so the bottom part which isMoulure en couronne à angle Par rapport à la table et au guideInglete recto para obtener instrucciones La mesa y al tope-guíaSe instala contra la pared esté contra el tope-guía Una lista completa de accesoriosCutting Round or Irregularly Shaped Material Special CutsCutting Bowed Material Cutting thin wide MaterialCoupes spéciales Cortes especialesCharging Battery Pack Important Charging NotesCarga del paquete de baterias Cargador de 1 hora La chargeExtension Cords AccessoriesAccessoires RallongesCordóns de extensión AccesoriosMotor Brush Replacement Maintenance LubricationService BatteriesRemplacement des Balais de moteur Mantenimiento y LubricaciónGraissage de l’outil NettoyageEntretien des lames RoulementsLubricación de las herramientas LimpiezaCuidado de las hojas CojinetesÉlectrique Troubleshooting GuideDuide de Dépannage GénéralitésGuía de Localización y reparación de averías EléctricasGenerales ’entretien RéglagesDéfaillance de pièces Accumulation de bran de sciePuntos de pivote sueltos ReténUse protección para los ojos Fallo de piezaPage Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Top Page Image Contents