Bosch Power Tools ROTOZIP RZ18V manual Operating Instructions, Changing the Collet

Page 12

RZ 2610925600 9-05 9/1/05 11:04 AM Page 12

CHANGING THE COLLET

The 1/8" collet is used with 1/8" diameter Zip bits, the 1/4" collet is used with 1/4" diameter Zip bits and the 5/32" collet is used with 5/32" diameter Zip bits. To change collets, first remove the bit. Continue to loosen and unscrew the collet nut until you can remove it from the tool. Remove the collet and replace it with the other (Fig. 4). (Each collet is double-ended, and either end is acceptable to use.) By hand, re-tighten the collet nut around the collet in a clockwise direction. You are now ready to insert a new bit as instructed in Installing Zip Bits (Fig. 2 or 3).

FIG. 4

COLLET

COLLET

NUT

OUTPUT SHAFT

REMOVING AND INSTALLING THE HARD

AUXILIARY CONTROL HANDLE

Turn the tool OFF and remove battery pack. Firmly grasp the tool. Depress and hold lock pin from either side of the handle. While depressing the lock pin, depress release button so lock pin is engaged, then remove handle (Fig. 5).

With the lock pin engage, gently engage the two (2) front latches on handle into the tool and push handle until it snaps securely into place.

Your handle is equipped with a bit and collet storage area. To open door, pull tab on door downward away from tool. To close door, lift

door upward toward the tool. Be sure door is closed to prevent bits from falling out.

LOCK

FIG. 5

PIN

 

RELEASE

BUTTON

TAB

BIT / COLLET

STORAGE

DOOR

Operating Instructions

BUMP-OFF SLIDE "ON/OFF" SWITCH

This tool is switched "ON" by the slide switch located on the front of the motor housing (Fig. 6).

TO TURN THE TOOL "ON" slide the switch button out to "I" position.

TO TURN THE TOOL "OFF" slide the switch button in to "0" position.

! WARNING

Hold the tool with both

hands while starting, since

 

torque from the motor can cause the tool to twist.

FIG. 6

1

0

BUMP-OFF

SLIDE "ON/OFF"

SWITCH

-12-

Image 12
Contents For English Parlez-vous français? SeeVoir Ver página General Safety Rules Work area safetyElectrical safety Personal safetyPower tool use and care Battery tool use and careService Spiral Saw Safety Rules Zipmate Abrasive Cut-Off Attachment Safety Rules RZ 2610925600 9-05 9/1/05 1104 AM Battery/Charger Battery CareReproductive harm. Some examples of these chemicals are Battery Disposal NICKEL-CADMIUM BatteriesSymbols Functional Description and Specifications Cordless Spiral SawHard Auxiliary Control Handle Tool ChargerAssembly Removing and Installing Depth Guide AssemblyRemoving and Installing RZVAC1 Vacuum Adapter Removing and Installing the Hard Auxiliary Control Handle BUMP-OFF Slide ON/OFF SwitchOperating Instructions Changing the ColletDepth Guide Adjustment Releasing and Inserting Battery PackCharging Battery Pack 30 Minute Single BAY-BC130 Important Charging Notes Make a FEW Practice Cuts StepImportant User TIP Making Drywall CUT OutsStep Wheel Guard Lock Lever Adjustment Screw Abrasive Shaft Lock Removing and InstallingZipmate Abrasive Cut Off Attachment Guard Abrasive Wheel Shaft Lock Outputarbor Shaftnut Making a CUTRZ 2610925600 9-05 9/1/05 1104 AM Maintenance CleaningExtension Cords Accessories & Attachments Zip BitsRZmas2 RZmet2 Masonry Cut-off Wheel Metal Cut-off Wheel Consignes générales de sécurité Sécurité du lieu de travailSécurité électrique Sécurité personnelleUtilisation et entretien des outils Électroportatifs Utilisation et entretien des outils à pilesEntretien Consignes de sécurité pour la scie Spiral Saw Tordre loutilRZ 2610925600 9-05 9/1/05 1104 AM Causes du rebond et façons dont Lopérateur peut le prévenir Chargeur de pile Entretien des pilesMise au rebut des piles Piles NICKEL-CADMIUMSymboles Description fonctionnelle et spécifications Scie Spiral Saw sans filOutil Chargeur Assemblage Guide DE ProfondeurDémontage ET Remontage DE L’ADAPTATEUR BlocageCommande Auxiliaire Dure Consignes de fonctionnementChangement DU Douille Avec Arrêt PAR PercussionDépose ET Repose DU BLOC-PILES Ajustement À Laide DU Guide DE ProfondeurRemarques Importantes Concernant LA Charge Exécuter DES Coupes D’ESSAI ÉtapeImportant Conseil Pour L’UTILISATEUR Étape Découpages Dans LES Murs SecsÉtape Accessoire de tronçonnage à meule Zipmate Montage ET Démontage DEMontage DE Meules ’appuyez pas sur lePour Tronçonner Mise EN Garde Entretien Cordons de rallongeNettoyage Accessoires Embouts ZipRZmas2 RZmet2 Disquede tronçonnage Pour maçonnerie Pour métalNormas generales de seguridad Seguridad del área de trabajoSeguridad eléctrica Seguridad personalMecánicas Uso y cuidado de las herramientas Alimentadas por bateríasServicio de ajustes y reparaciones Normas de seguridad para sierras Spiral Saw Comience Aquí Pieza DE Trabajo Broca Sentido DE AvanceRZ 2610925600 9-05 9/1/05 1104 AM Operador Batería/cargador Cuidado de las bateríasEliminación de las baterías Baterías DE NIQUEL-CADMIOSímbolos De Ni-CdDescripción funcional y especificaciones Sierra Spiral Saw inalámbricaHerramienta Cargador Ensamblaje LA Guía DE ProfundidadRemoción E Instalación DEL Adaptador DE Aspiradora RZVAC1 Cierre Tuerca DEL DE EJEInstrucciones de funcionamiento Cambio DEL PortaherramientaControl Auxiliar Duro Interruptor Corredizo DE Encendido Y ApagadoAjuste DE LA Guía DE Profundidad Liberacion E Insercion DEL Paquete DE BateríasNotas Importantes Para Cargar Haga Cortes DE Ensayo PasoConsejos Prácticos Paso Aditamento de rueda abrasiva Zipmate Advertencia 1-877-ROTOZIPRueda Abrasiva Realización DE Cortes Collarín EJE DE SalidaRZ 2610925600 9-05 9/1/05 1104 AM Mantenimiento Cordones de extensiónServicio LimpiezaAccesorios y aditamentos Brocas ZipRZmas2 RZmet2 Rueda de corte para Mampostería MetalesRZ 2610925600 9-05 9/1/05 1104 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools