Cabletron Systems TRMMIM manual Allowed/Disallowed List Conﬁguration Buttons

Page 108

Ring Security Conﬁguration

Allowed/Disallowed List Conﬁguration Buttons

The following buttons are used to manipulate the Allowed and Disallowed Lists and to set the security mode at the device:

This button moves a selected address(es) from the

Allowed List to the Disallowed List.

Note that if you are in the Warn mode, removing a station from the Allowed List will have little effect, because the station will remain on the ring and automatically be re-added to the Allowed List (although a trap will be sent to your management workstation when the station is re-added to the list). Note that the Allowed and Disallowed Lists will refresh automatically when a station reinserts into the ring.

If no items in the Allowed List are selected, this button will be grayed out.

This button moves a selected address(es) from the Disallowed List to the Allowed List. If there are no items selected in the Disallowed List, this button will be grayed out.

Selecting this button will delete selected address(es) from the Allowed or Disallowed Station Lists.

This button is active in all security modes; however, if you have Enable Security-Warnmode selected, the station will automatically be re-added to the Allowed List. Note that the Allowed List will automatically refresh when a station is re-added.

Selecting this button will invoke a pop-up window which allows you to add a station to the Allowed or Disallowed Station List (as described in the following section). This button is only active if security is enabled.

When pressed, this button will invoke a pop-up window that allows you to remove all address(es) from the Allowed List.

This button is active in all security modes; however, if you have Enable Security-Warnmode selected, the cleared stations will simply be re-added to the list. Note that the Allowed List refreshes automatically when stations are re-added.

Selecting this button will refresh both the Allowed List (stored on the TRMMIM itself) and the Disallowed List (stored on your management workstation). Should any

6-6	Launching the Security Conﬁguration Window

Image 108

Contents Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Alarm Conﬁguration Chapter Ring MapChapter Statistics Chapter Ring Security Conﬁguration Appendix a Trmmim MIB StructureContents Using the Trmmim User’s Guide TrmmimWhat’s not in the Trmmim Guide Introduction to Spma for the TrmmimConventions Screen DisplaysIntroduction to Spma for the Trmmim Using the Mouse ButtonGetting Help FTPTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub ViewUsing the Trmmim Hub View Navigating Through the Hub ViewHub View Front Panel Trmmim Hub ViewUptime Time and DateDevice Name Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display FormErrors FramesTotal Bytes Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and LocationChecking Module Status ContactDate and Time Total RingsSpeed Fault Speed Fault LocationModule Name ModuleAdmin State Checking Port StatusPort Name Module/PortChecking Station Status Link State TimeInsertion Trap Station Name VendorUpstream Neighbor/Downstream Neighbor Physical Location PriorityPort Mapping Reverse MACsChecking Ring Port Status Conﬁguring Station Name, Location, or PriorityFault State Time Media FaultClass Media TypeChecking Statistics Bytes LineBurst AbortManaging the Hub Managing the Hub at the Device LevelFind MAC Address Setting the Polling Intervals 12. The Find MAC Address Window13. Trmmim Polling Intervals Contact StatusDevice General Status Device ConﬁgurationPort Operational State StatisticsManaging the Hub at the Module Level Controlling Token Ring FNB Multiplexer ConnectionsINS Board Left ConnectRight Connect BypassControlling Token Ring Speed Clearing the Module FNB Conﬁguration Window SelectionsControlling Token Ring MIM Management Mode Enabling All Ports on Token Ring ModulesAuto AUT Management MGTManaging the Hub at the Port Level Converting a Station Port to a Ring-out PortEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the command line stand-alone mode Launching the Ring MapFrom the icon From the Hub ViewSelecting a Ring to Map Ring NameRing Map Speed StationsName UtilizationViewing Station-speciﬁc Information Quick Info Popup WindowBoard and Port DropSetting a Station Name Performance and ErrorsSetting a Station Drop Viewing Management Station ConﬁgurationCommands Error Status Open StatusError Active MonitorSetting the Statistics Calculation Mode Error Report TimerViewing Ring-level Information Viewing the Error Table Set Calculation Mode WindowError Table Window Total Errors Isolating ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information WindowViewing Beacon History Active Monitor ChangesRing Purges Beacon EventsLast Beacon Type Longest BeaconLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find WindowsFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest WindowsAlarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level AlarmAlarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics StatisticsViewing the Ring Station List Spmarun e5stats IP Address community nameModule and Port Stn NameUpstream Addr Downstream AddrUsing the Reverse MAC Button Monitoring Ring and Station StatisticsRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Ring and Station Variables GeneralProtocols KBytesIsolating Errors Line ErrorsBurst Error AC ErrorNon-Isolating Errors Abort ErrorInternal Error Token Errors Frequency ErrorsStatistics Ring and Station Variables Ring Security Conﬁguration About Ring SecurityLaunching the Security Conﬁguration Window Ring Security ConﬁgurationSecurity Conﬁguration Ring Selection window, -1, will appear Allowed Station List Allowed CountDisallowed Station List Disallowed CountSecurity Mode Options Disable SecurityEnable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List AutomaticallyDeleting Stations from the Allowed or Disallowed Lists Station Addition WindowClearing All Entries in the Allowed or Disallowed List Clear List WindowChanging the Ring Security Mode RemoveIetf MIB Support Trmmim MIB StructureChassis MGR Protocol StackSnmp Agent Network One, Network TwoBrief Word About MIB Components and Community Names TelnetTrmmim MIB Structure Index Index-2 Index-3 Index-4