Cabletron Systems TRMMIM Viewing Ring-level Information, Setting the Statistics Calculation Mode

Page 63

Ring Map

NOTE

If you disallow contention for a management station which is currently serving as the Active Monitor, that station will continue as Active Monitor until the next contention.

Error Report Timer

The Error Report Timer determines the interval at which stations will report the number of errors they have detected. The default timer value is 2 seconds. To change this value:

1.Highlight the current setting.

2.Type in a new setting, and press Enter.

NOTE

Current versions of TRMMIM ﬁrmware do not support the ability to set the Error Report Timer Delay; future versions will include this feature.

After making changes in the Management Station Conﬁguration window, click here to update the information shown in the window’s ﬁelds.

Viewing Ring-level Information

Setting the Statistics Calculation Mode

Statistics available from the Ring Map window are calculated according to one of three formulas:

Rate	Units expressed as a change in value divided by the
	length of the polling interval, or Δ units measured /Δ time
	(in seconds). For example, if you measured 3200 frames
	over a 10 second interval, the frame rate would be
	320/sec.
Cumulative	Total units measured since the cumulative option was
	selected. For example, if you measured 390 frames
	during the ﬁrst interval since cumulative was selected,
	270 in the second, and 500 in the third, the cumulative
	total would be 1160. You can reset the Ring Map’s
	cumulative counters at any time.
Delta	The change in the units measured from the previous poll
	to the current poll.

Viewing Ring-level Information

3-13

Image 63

Contents Trmmim Page Virus Disclaimer Applicable to licenses to the United States Government only Restricted Rights NoticeContents Chapter Alarm Conﬁguration Chapter Ring MapChapter Statistics Appendix a Trmmim MIB Structure Chapter Ring Security ConﬁgurationContents Trmmim Using the Trmmim User’s GuideIntroduction to Spma for the Trmmim What’s not in the Trmmim GuideScreen Displays ConventionsIntroduction to Spma for the Trmmim Button Using the MouseFTP Getting HelpTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Hub View Using the Trmmim Hub ViewNavigating Through the Hub View Using the Trmmim Hub ViewTrmmim Hub View Hub View Front PanelDevice Location UptimeTime and Date Device NameUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Port Display Form Hub View Port Color CodesPort Type ErrorsFrames Total BytesFNB Display Monitoring Hub Performance Using the Trmmim Hub View Name and Location Checking Device Status and Updating Front Panel InfoTotal Rings Checking Module StatusContact Date and TimeModule Speed FaultSpeed Fault Location Module NameModule/Port Admin StateChecking Port Status Port NameChecking Station Status Link State TimeInsertion Trap Station Name VendorUpstream Neighbor/Downstream Neighbor Reverse MACs Physical LocationPriority Port MappingConﬁguring Station Name, Location, or Priority Checking Ring Port StatusMedia Type Fault State TimeMedia Fault ClassChecking Statistics Abort BytesLine BurstManaging the Hub Managing the Hub at the Device LevelFind MAC Address 12. The Find MAC Address Window Setting the Polling IntervalsContact Status 13. Trmmim Polling IntervalsStatistics Device General StatusDevice Conﬁguration Port Operational StateControlling Token Ring FNB Multiplexer Connections Managing the Hub at the Module LevelINS Bypass BoardLeft Connect Right ConnectClearing the Module FNB Conﬁguration Window Selections Controlling Token Ring SpeedManagement MGT Controlling Token Ring MIM Management ModeEnabling All Ports on Token Ring Modules Auto AUTManaging the Hub at the Port Level Converting a Station Port to a Ring-out PortEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the Hub View From the command line stand-alone modeLaunching the Ring Map From the iconRing Name Selecting a Ring to MapRing Map Utilization SpeedStations NameQuick Info Popup Window Viewing Station-speciﬁc InformationDrop Board and PortPerformance and Errors Setting a Station NameViewing Management Station Conﬁguration Setting a Station DropCommands Open Status Error StatusActive Monitor ErrorSetting the Statistics Calculation Mode Error Report TimerViewing Ring-level Information Set Calculation Mode Window Viewing the Error TableError Table Window Isolating Errors Total ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Device Information Window Setting the Map Poll IntervalBeacon Events Viewing Beacon HistoryActive Monitor Changes Ring PurgesLast Beacon Type Longest BeaconLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options 13. Sample Find Windows Searching by Station Name, MAC Address, Board/Port, or DropFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds 14. Sample Find Highest and Lowest Windows Accessing Other Spma ApplicationsAlarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting a Ring Level Alarm Setting and Viewing Station AlarmsAlarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Statistics Using StatisticsSpmarun e5stats IP Address community name Viewing the Ring Station ListDownstream Addr Module and PortStn Name Upstream AddrUsing the Reverse MAC Button Monitoring Ring and Station StatisticsRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on KBytes Ring and Station VariablesGeneral ProtocolsAC Error Isolating ErrorsLine Errors Burst ErrorNon-Isolating Errors Abort ErrorInternal Error Frequency Errors Token ErrorsStatistics Ring and Station Variables About Ring Security Ring Security ConﬁgurationRing Security Conﬁguration Launching the Security Conﬁguration WindowSecurity Conﬁguration Ring Selection window, -1, will appear Disallowed Count Allowed Station ListAllowed Count Disallowed Station ListSecurity Mode Options Disable SecurityEnable Security Allowed/Disallowed List Conﬁguration Buttons Building the Allowed List Automatically Conﬁguring SecurityStation Addition Window Deleting Stations from the Allowed or Disallowed ListsClear List Window Clearing All Entries in the Allowed or Disallowed ListRemove Changing the Ring Security ModeTrmmim MIB Structure Ietf MIB SupportNetwork One, Network Two Chassis MGRProtocol Stack Snmp AgentTelnet Brief Word About MIB Components and Community NamesTrmmim MIB Structure Index Index-2 Index-3 Index-4