Cabletron Systems TRMMIM manual Using the Trmmim Hub View, Using the Hub View

Page 17

Chapter 2

Using the TRMMIM Hub View

Navigating through the Hub View, monitoring hub activity; managing the hub at the device, module, and port levels

The heart of the SPECTRUM Portable Management Application (SPMA) for the TRMMIM is the Hub View, a graphical interface that gives you access to many of the functions that provide control over the TRMMIM-managed hub.

NOTE

Note that the Hub View application only allows you to control boards and ports in the domain of a single management module. If you have another management module installed in the chassis to the left of the monitored TRMMIM, boards that are under the domain of that module (i.e., Media Interface Modules – or MIMs – to its left) will still display in the Hub View of the monitored TRMMIM; however, only boards within the domain of the monitored TRMMIM can be correctly controlled. Flexible Network Bus (FNB) connections across the MMAC chassis will be displayed regardless of modules installed; however, only FNB connections within the domain of the monitored module can be controlled. For example, if you had a TRMMIM and a TRBMIM installed in the same chassis with the TRBMIM to the left of the TRMMIM, and you were modeling the TRMMIM in a Hub View, you would have to create a separate Hub View for the TRBMIM to control the FNB connections and manage MIMs to the left of the TRBMIM. However, even while modeling the TRMMIM, you would still be able to view the boards and FNB connections across the entire MMAC.

Using the Hub View

There are two ways to open the Hub View: if you are working within a network management system, you can select the Hub View option from the icon menu; specific directions for creating a TRMMIM icon and accessing the icon menu can be found in the appropriate Installing and Using SPECTRUM for... guide. If you are running the TRMMIM module in a stand-alone mode, type the following at the command line:

spmarun e5hub <IP address> <community name>

2-1

Image 17
Contents Trmmim Page Virus Disclaimer Applicable to licenses to the United States Government only Restricted Rights NoticeContents Chapter Statistics Chapter Alarm ConfigurationChapter Ring Map Appendix a Trmmim MIB Structure Chapter Ring Security ConfigurationContents Trmmim Using the Trmmim User’s GuideIntroduction to Spma for the Trmmim What’s not in the Trmmim GuideScreen Displays ConventionsIntroduction to Spma for the Trmmim Button Using the MouseFTP Getting HelpTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Hub View Using the Trmmim Hub ViewNavigating Through the Hub View Using the Trmmim Hub ViewTrmmim Hub View Hub View Front PanelTime and Date UptimeDevice Name Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Port Display Form Hub View Port Color CodesFrames ErrorsTotal Bytes Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Name and Location Checking Device Status and Updating Front Panel InfoContact Checking Module StatusDate and Time Total RingsSpeed Fault Location Speed FaultModule Name ModuleChecking Port Status Admin StatePort Name Module/PortInsertion Trap Checking Station StatusLink State Time Upstream Neighbor/Downstream Neighbor Station NameVendor Priority Physical LocationPort Mapping Reverse MACsConfiguring Station Name, Location, or Priority Checking Ring Port StatusMedia Fault Fault State TimeClass Media TypeChecking Statistics Line BytesBurst AbortFind MAC Address Managing the HubManaging the Hub at the Device Level 12. The Find MAC Address Window Setting the Polling IntervalsContact Status 13. Trmmim Polling IntervalsDevice Configuration Device General StatusPort Operational State StatisticsControlling Token Ring FNB Multiplexer Connections Managing the Hub at the Module LevelINS Left Connect BoardRight Connect BypassClearing the Module FNB Configuration Window Selections Controlling Token Ring SpeedEnabling All Ports on Token Ring Modules Controlling Token Ring MIM Management ModeAuto AUT Management MGTEnabling and Disabling Station and Ring Ports Managing the Hub at the Port LevelConverting a Station Port to a Ring-out Port Removing a Station from the Ring Ring Map Launching the Ring Map From the command line stand-alone modeFrom the icon From the Hub ViewRing Name Selecting a Ring to MapRing Map Stations SpeedName UtilizationQuick Info Popup Window Viewing Station-specific InformationDrop Board and PortPerformance and Errors Setting a Station NameViewing Management Station Configuration Setting a Station DropCommands Open Status Error StatusActive Monitor ErrorViewing Ring-level Information Setting the Statistics Calculation ModeError Report Timer Set Calculation Mode Window Viewing the Error TableError Table Window Isolating Errors Total ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Device Information Window Setting the Map Poll IntervalActive Monitor Changes Viewing Beacon HistoryRing Purges Beacon EventsLast Beacon Last Beacon TypeLongest Beacon Beacon Configuration 12. The Beacon Configuration Window Using the Find Options 13. Sample Find Windows Searching by Station Name, MAC Address, Board/Port, or DropFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds 14. Sample Find Highest and Lowest Windows Accessing Other Spma ApplicationsAlarm Configuration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Configuration Setting a Ring Level Alarm Setting and Viewing Station AlarmsAlarm Configuration Alarm Configuration Alarm Configuration Setting a Station Level Alarm Alarm Configuration Setting and Viewing Station Alarms Statistics Using StatisticsSpmarun e5stats IP Address community name Viewing the Ring Station ListStn Name Module and PortUpstream Addr Downstream AddrRefreshing the Station List Using the Reverse MAC ButtonMonitoring Ring and Station Statistics Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on General Ring and Station VariablesProtocols KBytesLine Errors Isolating ErrorsBurst Error AC ErrorInternal Error Non-Isolating ErrorsAbort Error Frequency Errors Token ErrorsStatistics Ring and Station Variables About Ring Security Ring Security ConfigurationRing Security Configuration Launching the Security Configuration WindowSecurity Configuration Ring Selection window, -1, will appear Allowed Count Allowed Station ListDisallowed Station List Disallowed CountEnable Security Security Mode OptionsDisable Security Allowed/Disallowed List Configuration Buttons Building the Allowed List Automatically Configuring SecurityStation Addition Window Deleting Stations from the Allowed or Disallowed ListsClear List Window Clearing All Entries in the Allowed or Disallowed ListRemove Changing the Ring Security ModeTrmmim MIB Structure Ietf MIB SupportProtocol Stack Chassis MGRSnmp Agent Network One, Network TwoTelnet Brief Word About MIB Components and Community NamesTrmmim MIB Structure Index Index-2 Index-3 Index-4