Cabletron Systems TRMMIM manual Open Status, Error Status

Page 61

Ring Map

Open Status

This field displays the result of the last “open” command or the last attempt by the management station to open onto the ring: whether the management station did in fact open onto the ring, or if an error occurred. This field may display any one of the following:

No Open

An open command has not been issued.

Bad Param

The open command could not be completed because the

 

parameters did not allow for the station to be opened

 

onto the ring.

Lobe Test Failed

The lobe media check has failed for the management

 

station.

Signal Loss

A signal loss condition has been detected at the

 

management station’s receiver input during the open

 

process.

Insertion Timeout

The management station has failed to logically insert on

 

the ring before the insertion timer expires.

Purge Failed

The management station has timed out when attempting

 

a ring purge after becoming the active monitor: that is,

 

the management station was unable to receive its own

 

ring purge MAC frames.

Beaconing

The management station received a beacon MAC frame

 

after physically inserting into the ring.

Duplicate MAC

Another station on the ring has the same MAC address

Address

as the management station.

Parameter Requested

The management station has determined that a Ring

 

Parameter Server (RPS) is present on the ring, but it does

 

not respond to a request initialization MAC frame.

Remove Received

The management station received a remove adapter

 

MAC frame during the insertion process.

Open

The open command was completed successfully.

Error Status

This field displays a number associated with the most recent error status that was reported by the management station. It is possible for more than one error status to be reported at one time; in this case, the number displayed would be the sum of the codes of the last errors recorded. The following table lists the possible errors and their corresponding error codes:

Viewing Station-specific Information

3-11

Image 61
Contents Trmmim Page Virus Disclaimer Applicable to licenses to the United States Government only Restricted Rights NoticeContents Chapter Ring Map Chapter Alarm ConfigurationChapter Statistics Appendix a Trmmim MIB Structure Chapter Ring Security ConfigurationContents Trmmim Using the Trmmim User’s GuideIntroduction to Spma for the Trmmim What’s not in the Trmmim GuideScreen Displays ConventionsIntroduction to Spma for the Trmmim Button Using the MouseFTP Getting HelpTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Hub View Using the Trmmim Hub ViewNavigating Through the Hub View Using the Trmmim Hub ViewTrmmim Hub View Hub View Front PanelTime and Date UptimeDevice Name Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Port Display Form Hub View Port Color CodesFrames ErrorsTotal Bytes Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Name and Location Checking Device Status and Updating Front Panel InfoContact Checking Module StatusDate and Time Total RingsSpeed Fault Location Speed FaultModule Name ModuleChecking Port Status Admin StatePort Name Module/PortLink State Time Checking Station StatusInsertion Trap Vendor Station NameUpstream Neighbor/Downstream Neighbor Priority Physical LocationPort Mapping Reverse MACsConfiguring Station Name, Location, or Priority Checking Ring Port StatusMedia Fault Fault State TimeClass Media TypeChecking Statistics Line BytesBurst AbortManaging the Hub at the Device Level Managing the HubFind MAC Address 12. The Find MAC Address Window Setting the Polling IntervalsContact Status 13. Trmmim Polling IntervalsDevice Configuration Device General StatusPort Operational State StatisticsControlling Token Ring FNB Multiplexer Connections Managing the Hub at the Module LevelINS Left Connect BoardRight Connect BypassClearing the Module FNB Configuration Window Selections Controlling Token Ring SpeedEnabling All Ports on Token Ring Modules Controlling Token Ring MIM Management ModeAuto AUT Management MGTConverting a Station Port to a Ring-out Port Managing the Hub at the Port LevelEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map Launching the Ring Map From the command line stand-alone modeFrom the icon From the Hub ViewRing Name Selecting a Ring to MapRing Map Stations SpeedName UtilizationQuick Info Popup Window Viewing Station-specific InformationDrop Board and PortPerformance and Errors Setting a Station NameViewing Management Station Configuration Setting a Station DropCommands Open Status Error StatusActive Monitor ErrorError Report Timer Setting the Statistics Calculation ModeViewing Ring-level Information Set Calculation Mode Window Viewing the Error TableError Table Window Isolating Errors Total ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Device Information Window Setting the Map Poll IntervalActive Monitor Changes Viewing Beacon HistoryRing Purges Beacon EventsLongest Beacon Last Beacon TypeLast Beacon Beacon Configuration 12. The Beacon Configuration Window Using the Find Options 13. Sample Find Windows Searching by Station Name, MAC Address, Board/Port, or DropFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds 14. Sample Find Highest and Lowest Windows Accessing Other Spma ApplicationsAlarm Configuration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Configuration Setting a Ring Level Alarm Setting and Viewing Station AlarmsAlarm Configuration Alarm Configuration Alarm Configuration Setting a Station Level Alarm Alarm Configuration Setting and Viewing Station Alarms Statistics Using StatisticsSpmarun e5stats IP Address community name Viewing the Ring Station ListStn Name Module and PortUpstream Addr Downstream AddrMonitoring Ring and Station Statistics Using the Reverse MAC ButtonRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on General Ring and Station VariablesProtocols KBytesLine Errors Isolating ErrorsBurst Error AC ErrorAbort Error Non-Isolating ErrorsInternal Error Frequency Errors Token ErrorsStatistics Ring and Station Variables About Ring Security Ring Security ConfigurationRing Security Configuration Launching the Security Configuration WindowSecurity Configuration Ring Selection window, -1, will appear Allowed Count Allowed Station ListDisallowed Station List Disallowed CountDisable Security Security Mode OptionsEnable Security Allowed/Disallowed List Configuration Buttons Building the Allowed List Automatically Configuring SecurityStation Addition Window Deleting Stations from the Allowed or Disallowed ListsClear List Window Clearing All Entries in the Allowed or Disallowed ListRemove Changing the Ring Security ModeTrmmim MIB Structure Ietf MIB SupportProtocol Stack Chassis MGRSnmp Agent Network One, Network TwoTelnet Brief Word About MIB Components and Community NamesTrmmim MIB Structure Index Index-2 Index-3 Index-4