Cabletron Systems TRMMIM manual Alarm Conﬁguration

Page 86

Alarm Conﬁguration

NOTE

You need not close the Ring Alarms window before launching the Station Alarms window; just move the Ring Alarms window out of the way, if necessary, to reach the main Ring/Stn Alarms window.

Figure 4-3. The Station Alarms Window

The alarm Timebase displayed here is deﬁned in the Ring Alarms window and applies to all enabled alarms at both the ring and station levels; this is the interval (in seconds) over which the selected variable(s) will be counted for comparison to the threshold values. For example, if the Burst Errors alarm is enabled, the threshold is set at 10, and the timebase is set to 10 seconds, the TRMMIM will generate an alarm if 10 burst errors are detected by the selected station(s) within a 10-second time period.

4-6	Setting and Viewing Station Alarms

Image 86

Contents Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Statistics Chapter Alarm ConﬁgurationChapter Ring Map Chapter Ring Security Conﬁguration Appendix a Trmmim MIB StructureContents Using the Trmmim User’s Guide TrmmimWhat’s not in the Trmmim Guide Introduction to Spma for the TrmmimConventions Screen DisplaysIntroduction to Spma for the Trmmim Using the Mouse ButtonGetting Help FTPTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub ViewUsing the Trmmim Hub View Navigating Through the Hub ViewHub View Front Panel Trmmim Hub ViewDevice Name UptimeTime and Date Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display FormTotal Bytes ErrorsFrames Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and LocationDate and Time Checking Module StatusContact Total RingsModule Name Speed FaultSpeed Fault Location ModulePort Name Admin StateChecking Port Status Module/PortInsertion Trap Checking Station StatusLink State Time Upstream Neighbor/Downstream Neighbor Station NameVendor Port Mapping Physical LocationPriority Reverse MACsChecking Ring Port Status Conﬁguring Station Name, Location, or PriorityClass Fault State TimeMedia Fault Media TypeChecking Statistics Burst BytesLine AbortFind MAC Address Managing the HubManaging the Hub at the Device Level Setting the Polling Intervals 12. The Find MAC Address Window13. Trmmim Polling Intervals Contact StatusPort Operational State Device General StatusDevice Conﬁguration StatisticsManaging the Hub at the Module Level Controlling Token Ring FNB Multiplexer ConnectionsINS Right Connect BoardLeft Connect BypassControlling Token Ring Speed Clearing the Module FNB Conﬁguration Window SelectionsAuto AUT Controlling Token Ring MIM Management ModeEnabling All Ports on Token Ring Modules Management MGTEnabling and Disabling Station and Ring Ports Managing the Hub at the Port LevelConverting a Station Port to a Ring-out Port Removing a Station from the Ring Ring Map From the icon From the command line stand-alone modeLaunching the Ring Map From the Hub ViewSelecting a Ring to Map Ring NameRing Map Name SpeedStations UtilizationViewing Station-speciﬁc Information Quick Info Popup WindowBoard and Port DropSetting a Station Name Performance and ErrorsSetting a Station Drop Viewing Management Station ConﬁgurationCommands Error Status Open StatusError Active MonitorViewing Ring-level Information Setting the Statistics Calculation ModeError Report Timer Viewing the Error Table Set Calculation Mode WindowError Table Window Total Errors Isolating ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information WindowRing Purges Viewing Beacon HistoryActive Monitor Changes Beacon EventsLast Beacon Last Beacon TypeLongest Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find WindowsFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest WindowsAlarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level AlarmAlarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics StatisticsViewing the Ring Station List Spmarun e5stats IP Address community nameUpstream Addr Module and PortStn Name Downstream AddrRefreshing the Station List Using the Reverse MAC ButtonMonitoring Ring and Station Statistics Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Protocols Ring and Station VariablesGeneral KBytesBurst Error Isolating ErrorsLine Errors AC ErrorInternal Error Non-Isolating ErrorsAbort Error Token Errors Frequency ErrorsStatistics Ring and Station Variables Ring Security Conﬁguration About Ring SecurityLaunching the Security Conﬁguration Window Ring Security ConﬁgurationSecurity Conﬁguration Ring Selection window, -1, will appear Disallowed Station List Allowed Station ListAllowed Count Disallowed CountEnable Security Security Mode OptionsDisable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List AutomaticallyDeleting Stations from the Allowed or Disallowed Lists Station Addition WindowClearing All Entries in the Allowed or Disallowed List Clear List WindowChanging the Ring Security Mode RemoveIetf MIB Support Trmmim MIB StructureSnmp Agent Chassis MGRProtocol Stack Network One, Network TwoBrief Word About MIB Components and Community Names TelnetTrmmim MIB Structure Index Index-2 Index-3 Index-4