Cabletron Systems TRMMIM manual Alarm Conﬁguration Setting and Viewing Station Alarms

Page 90

Alarm Conﬁguration

4-10	Setting and Viewing Station Alarms

Image 90

Contents Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Alarm Conﬁguration Chapter Ring MapChapter Statistics Chapter Ring Security Conﬁguration Appendix a Trmmim MIB StructureContents Using the Trmmim User’s Guide TrmmimWhat’s not in the Trmmim Guide Introduction to Spma for the TrmmimConventions Screen DisplaysIntroduction to Spma for the Trmmim Using the Mouse ButtonGetting Help FTPTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub ViewUsing the Trmmim Hub View Navigating Through the Hub ViewHub View Front Panel Trmmim Hub ViewDevice Name UptimeTime and Date Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display FormTotal Bytes ErrorsFrames Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and LocationDate and Time Checking Module StatusContact Total RingsModule Name Speed FaultSpeed Fault Location ModulePort Name Admin StateChecking Port Status Module/PortChecking Station Status Link State TimeInsertion Trap Station Name VendorUpstream Neighbor/Downstream Neighbor Port Mapping Physical LocationPriority Reverse MACsChecking Ring Port Status Conﬁguring Station Name, Location, or PriorityClass Fault State TimeMedia Fault Media TypeChecking Statistics Burst BytesLine AbortManaging the Hub Managing the Hub at the Device LevelFind MAC Address Setting the Polling Intervals 12. The Find MAC Address Window13. Trmmim Polling Intervals Contact StatusPort Operational State Device General StatusDevice Conﬁguration StatisticsManaging the Hub at the Module Level Controlling Token Ring FNB Multiplexer ConnectionsINS Right Connect BoardLeft Connect BypassControlling Token Ring Speed Clearing the Module FNB Conﬁguration Window SelectionsAuto AUT Controlling Token Ring MIM Management ModeEnabling All Ports on Token Ring Modules Management MGTManaging the Hub at the Port Level Converting a Station Port to a Ring-out PortEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the icon From the command line stand-alone modeLaunching the Ring Map From the Hub ViewSelecting a Ring to Map Ring NameRing Map Name SpeedStations UtilizationViewing Station-speciﬁc Information Quick Info Popup WindowBoard and Port DropSetting a Station Name Performance and ErrorsSetting a Station Drop Viewing Management Station ConﬁgurationCommands Error Status Open StatusError Active MonitorSetting the Statistics Calculation Mode Error Report TimerViewing Ring-level Information Viewing the Error Table Set Calculation Mode WindowError Table Window Total Errors Isolating ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information WindowRing Purges Viewing Beacon HistoryActive Monitor Changes Beacon EventsLast Beacon Type Longest BeaconLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find WindowsFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest WindowsAlarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level AlarmAlarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics StatisticsViewing the Ring Station List Spmarun e5stats IP Address community nameUpstream Addr Module and PortStn Name Downstream AddrUsing the Reverse MAC Button Monitoring Ring and Station StatisticsRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Protocols Ring and Station VariablesGeneral KBytesBurst Error Isolating ErrorsLine Errors AC ErrorNon-Isolating Errors Abort ErrorInternal Error Token Errors Frequency ErrorsStatistics Ring and Station Variables Ring Security Conﬁguration About Ring SecurityLaunching the Security Conﬁguration Window Ring Security ConﬁgurationSecurity Conﬁguration Ring Selection window, -1, will appear Disallowed Station List Allowed Station ListAllowed Count Disallowed CountSecurity Mode Options Disable SecurityEnable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List AutomaticallyDeleting Stations from the Allowed or Disallowed Lists Station Addition WindowClearing All Entries in the Allowed or Disallowed List Clear List WindowChanging the Ring Security Mode RemoveIetf MIB Support Trmmim MIB StructureSnmp Agent Chassis MGRProtocol Stack Network One, Network TwoBrief Word About MIB Components and Community Names TelnetTrmmim MIB Structure Index Index-2 Index-3 Index-4