Cabletron Systems TRMMIM manual Setting a Station Name, Performance and Errors

Page 58

Ring Map

Utilization

The percentage of the total usable bandwidth (4 or 16 Mb) that is currently being used by the station. This field will update after each polling interval.

Performance and Errors

Error and performance statistics for the selected station are displayed according to the currently selected calculation mode. Statistics displayed are:

Frames

Bytes

Line

Burst

AC

Abort Seq

Internal

Lost Frames

Congestion

Frame Copied

Token

Frequency

See Viewing the Error Table, page 3-14, for detailed definitions of these statistics.

Setting a Station Name

Using the Ring Map window, you can administratively assign a name to any station on the monitored ring network.

To do so:

1.Click mouse button 3 on any station label in the map.

2.Drag down to Set Name, and release. The Set Station Name window, Figure 3-4, will appear.

Figure 3-4. Set Station Name Window

3.In the Enter Name text field, enter a name (up to 10 ASCII characters) for the selected station.

4.Click on . The new name will be set at the station.

3-8

Viewing Station-specific Information

Image 58
Contents Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Ring Map Chapter Alarm ConfigurationChapter Statistics Chapter Ring Security Configuration Appendix a Trmmim MIB StructureContents Using the Trmmim User’s Guide TrmmimWhat’s not in the Trmmim Guide Introduction to Spma for the TrmmimConventions Screen DisplaysIntroduction to Spma for the Trmmim Using the Mouse ButtonGetting Help FTPTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub ViewUsing the Trmmim Hub View Navigating Through the Hub ViewHub View Front Panel Trmmim Hub ViewDevice Name UptimeTime and Date Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display FormTotal Bytes ErrorsFrames Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and LocationDate and Time Checking Module StatusContact Total RingsModule Name Speed FaultSpeed Fault Location ModulePort Name Admin StateChecking Port Status Module/PortLink State Time Checking Station StatusInsertion Trap Vendor Station NameUpstream Neighbor/Downstream Neighbor Port Mapping Physical LocationPriority Reverse MACsChecking Ring Port Status Configuring Station Name, Location, or PriorityClass Fault State TimeMedia Fault Media TypeChecking Statistics Burst BytesLine AbortManaging the Hub at the Device Level Managing the HubFind MAC Address Setting the Polling Intervals 12. The Find MAC Address Window13. Trmmim Polling Intervals Contact StatusPort Operational State Device General StatusDevice Configuration StatisticsManaging the Hub at the Module Level Controlling Token Ring FNB Multiplexer ConnectionsINS Right Connect BoardLeft Connect BypassControlling Token Ring Speed Clearing the Module FNB Configuration Window SelectionsAuto AUT Controlling Token Ring MIM Management ModeEnabling All Ports on Token Ring Modules Management MGTConverting a Station Port to a Ring-out Port Managing the Hub at the Port LevelEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the icon From the command line stand-alone modeLaunching the Ring Map From the Hub ViewSelecting a Ring to Map Ring NameRing Map Name SpeedStations UtilizationViewing Station-specific Information Quick Info Popup WindowBoard and Port DropSetting a Station Name Performance and ErrorsSetting a Station Drop Viewing Management Station ConfigurationCommands Error Status Open StatusError Active MonitorError Report Timer Setting the Statistics Calculation ModeViewing Ring-level Information Viewing the Error Table Set Calculation Mode WindowError Table Window Total Errors Isolating ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information WindowRing Purges Viewing Beacon HistoryActive Monitor Changes Beacon EventsLongest Beacon Last Beacon TypeLast Beacon Beacon Configuration 12. The Beacon Configuration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find WindowsFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest WindowsAlarm Configuration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Configuration Setting and Viewing Station Alarms Setting a Ring Level AlarmAlarm Configuration Alarm Configuration Alarm Configuration Setting a Station Level Alarm Alarm Configuration Setting and Viewing Station Alarms Using Statistics StatisticsViewing the Ring Station List Spmarun e5stats IP Address community nameUpstream Addr Module and PortStn Name Downstream AddrMonitoring Ring and Station Statistics Using the Reverse MAC ButtonRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Protocols Ring and Station VariablesGeneral KBytesBurst Error Isolating ErrorsLine Errors AC ErrorAbort Error Non-Isolating ErrorsInternal Error Token Errors Frequency ErrorsStatistics Ring and Station Variables Ring Security Configuration About Ring SecurityLaunching the Security Configuration Window Ring Security ConfigurationSecurity Configuration Ring Selection window, -1, will appear Disallowed Station List Allowed Station ListAllowed Count Disallowed CountDisable Security Security Mode OptionsEnable Security Allowed/Disallowed List Configuration Buttons Configuring Security Building the Allowed List AutomaticallyDeleting Stations from the Allowed or Disallowed Lists Station Addition WindowClearing All Entries in the Allowed or Disallowed List Clear List WindowChanging the Ring Security Mode RemoveIetf MIB Support Trmmim MIB StructureSnmp Agent Chassis MGRProtocol Stack Network One, Network TwoBrief Word About MIB Components and Community Names TelnetTrmmim MIB Structure Index Index-2 Index-3 Index-4