Cabletron Systems TRMMIM manual Uptime, Time and Date, Device Name, Device Location, IP Address

Page 20

Using the TRMMIM Hub View

Uptime

The time that the device has been running without interruption. The counter resets to 0 days 00:00:00 (days HH:MM:SS) when one of the following occurs:

•Power to the MMAC chassis is cycled.

•The device is reset manually.

Time and Date

The date and time are taken from the device’s internal clock.

Device Name

A text ﬁeld that you can use to help identify the device.

Device Location

A text ﬁeld that you can use to help identify the device.

NOTE

If the TRMMIM you are modeling is installed in an MMAC-3 chassis, its window titles will be truncated. If you have assigned a device name or location that contains more than 19 characters, only the ﬁrst 19 will be displayed in the Hub View. Check the Device Status window for the complete name and/or location, if necessary. See Checking Device Status and Updating Front Panel Info, on page 2-13,for details.

IP Address

The device’s Internet Protocol (IP) address. You can’t change the TRMMIM’s IP address from SPMA.

MAC Address

The device’s factory-set hardware address. The MAC address cannot be changed from SPMA.

Clicking on the Device button displays the Device menu, Figure 2-2.

2-4	Using the Hub View

Image 20

Contents Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Statistics Chapter Alarm ConﬁgurationChapter Ring Map Chapter Ring Security Conﬁguration Appendix a Trmmim MIB StructureContents Using the Trmmim User’s Guide TrmmimWhat’s not in the Trmmim Guide Introduction to Spma for the TrmmimConventions Screen DisplaysIntroduction to Spma for the Trmmim Using the Mouse ButtonGetting Help FTPTrmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub ViewUsing the Trmmim Hub View Navigating Through the Hub ViewHub View Front Panel Trmmim Hub ViewUptime Time and DateDevice Name Device LocationUsing the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display FormErrors FramesTotal Bytes Port TypeFNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and LocationChecking Module Status ContactDate and Time Total RingsSpeed Fault Speed Fault LocationModule Name ModuleAdmin State Checking Port StatusPort Name Module/PortInsertion Trap Checking Station StatusLink State Time Upstream Neighbor/Downstream Neighbor Station NameVendor Physical Location PriorityPort Mapping Reverse MACsChecking Ring Port Status Conﬁguring Station Name, Location, or PriorityFault State Time Media FaultClass Media TypeChecking Statistics Bytes LineBurst AbortFind MAC Address Managing the HubManaging the Hub at the Device Level Setting the Polling Intervals 12. The Find MAC Address Window13. Trmmim Polling Intervals Contact StatusDevice General Status Device ConﬁgurationPort Operational State StatisticsManaging the Hub at the Module Level Controlling Token Ring FNB Multiplexer ConnectionsINS Board Left ConnectRight Connect BypassControlling Token Ring Speed Clearing the Module FNB Conﬁguration Window SelectionsControlling Token Ring MIM Management Mode Enabling All Ports on Token Ring ModulesAuto AUT Management MGTEnabling and Disabling Station and Ring Ports Managing the Hub at the Port LevelConverting a Station Port to a Ring-out Port Removing a Station from the Ring Ring Map From the command line stand-alone mode Launching the Ring MapFrom the icon From the Hub ViewSelecting a Ring to Map Ring NameRing Map Speed StationsName UtilizationViewing Station-speciﬁc Information Quick Info Popup WindowBoard and Port DropSetting a Station Name Performance and ErrorsSetting a Station Drop Viewing Management Station ConﬁgurationCommands Error Status Open StatusError Active MonitorViewing Ring-level Information Setting the Statistics Calculation ModeError Report Timer Viewing the Error Table Set Calculation Mode WindowError Table Window Total Errors Isolating ErrorsNon-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information WindowViewing Beacon History Active Monitor ChangesRing Purges Beacon EventsLast Beacon Last Beacon TypeLongest Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find WindowsFinding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest WindowsAlarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level AlarmAlarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics StatisticsViewing the Ring Station List Spmarun e5stats IP Address community nameModule and Port Stn NameUpstream Addr Downstream AddrRefreshing the Station List Using the Reverse MAC ButtonMonitoring Ring and Station Statistics Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Ring and Station Variables GeneralProtocols KBytesIsolating Errors Line ErrorsBurst Error AC ErrorInternal Error Non-Isolating ErrorsAbort Error Token Errors Frequency ErrorsStatistics Ring and Station Variables Ring Security Conﬁguration About Ring SecurityLaunching the Security Conﬁguration Window Ring Security ConﬁgurationSecurity Conﬁguration Ring Selection window, -1, will appear Allowed Station List Allowed CountDisallowed Station List Disallowed CountEnable Security Security Mode OptionsDisable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List AutomaticallyDeleting Stations from the Allowed or Disallowed Lists Station Addition WindowClearing All Entries in the Allowed or Disallowed List Clear List WindowChanging the Ring Security Mode RemoveIetf MIB Support Trmmim MIB StructureChassis MGR Protocol StackSnmp Agent Network One, Network TwoBrief Word About MIB Components and Community Names TelnetTrmmim MIB Structure Index Index-2 Index-3 Index-4