Vicks PS-0K, PS-3K Before starting welding operations, Safety measures at the installation site

Page 21

R

Safety instructions

•Wear leather gloves with sleeves

•Wear neither rings, watches nor electrically conducting jewellery

•Wear protective goggles with eye-protecting lens of shade number 2. (DIN 58211, part 6). Weld spatters and light flashes are generated during welding operations.

•Wear protective goggles with side shields when removing slag

•Wear ear protection. A loud acoustic shock is generated when discharging the capacitors.

3.7Before starting welding operations ...

•Verify the state of all cables before starting a welding operation

•Immediately replace any faulty cables and cable connections

•Ensure that ventilation openings in the stud welder housing are not covered. The Stud Welder may otherwise be damaged as a result of heat accumulation.

3.8Safety measures at the installation site

•Ensure when installing the Stud Welder on tables or similar workshop furniture that the Stud Welder is positioned firmly and that the table or appropriate furniture can bear the appropriate load.

•Ensure that the power socket and the Stud Welder have been connected to the ground properly

•Observe fire prevention regulations and do not carry out any welding operations in hazardous locations

•Ensure that the room is ventilated well or if necessary, extract the welding vapours.

DANGER TO HEALTH

During welding operations vapours and suspended matters may be generated. In particular beware of fumes detrimental to health when using surface-treated materials. If possible only carry out welding operations in rooms which have a room height exceeding 3 m. Special regulations in accordance with VBG 15 are applicable for narrow rooms.

3-14

Image 21

Contents PS-3K PS-0K PS-1K PS-3K PS-0K PS-1K GmbH Page Table of Contents Maintenance Setting the Stud Welding PistolInitiation Quality controlSpare parts Following should be principally observed General informationIntended use Chapters of Operating Instructions Information on the documentationReaction in the case of malfunctions Information on Operating InstructionsTechnology of tip ignition Description of the Stud Welding PistolsStud Welding Pistol PS-1 Stud Welding Pistol PS-3K Stud Welding Pistol PS-0K PS OMStud Welding Pistol PS-1K PS-1 PS-3K PS-0K PS-1K Technical dataCharacterisation of references in the Operating Instructions Safety instructionsStaff qualification and training Safety-conscious workingFollowing should be observed prior to initiation Safety instructions for the User/OperatorBefore starting welding operations Safety measures at the installation siteIndependent retrofitting and spare parts production Working with the Stud WelderNon-permissible operating modes Setting the Stud Holder Setting the Stud Welding PistolInstalling the stud holder in the Stud Welding Pistol Spring pressure Setting the spring pressureGeneral view InitiationOperation Connecting the Stud Welding Pistols to the Stud WelderWelding parameters Stud Welder BMS-660-90Stud Welder BMS-690-135 Stud Welder BMS-8H Stud Welder BMS-6HQuality Control Type and scope of testingGeneral information Demands on the companyNormal work test Implementation of sample takingSimplified work test Production of samplesBending test Tension testMaintenance Stud Welding PistolsReplacing components Spare parts Spare parts list for Stud Welding Pistol PS-1Perspective presentation of Stud Welding Pistol PS-1 Spare parts list for Stud Welding Pistol PS-3K Perspective presentation of Stud Welding Pistol PS-3K Spare parts list for Stud Welding Pistol PS-0K Perspective presentation of Stud Welding Pistol PS-0K Spare parts list for Stud Welding Pistol PS-1K Perspective presentation of Stud Welding Pistol PS-1K Troubleshooting Functional breakdowns Standards and List of Directives Warranty TermsHeinz Soyer Bolzenschweißtechnik GmbH