Vicks PS-3K, PS-0K, PS-1K Setting the Stud Welding Pistol, Setting the Stud Holder

Page 24

R

Setting the Stud Welding Pistol

4. Setting the Stud Welding Pistol

4.1Setting the Stud Holder

The stud holders of the Stud Welding Pistols PS-1, PS-3K, PS-0K and PS-1K have the same construction. If long welding studs are used it is, however, due to the short construction form of the Stud Welding Pistols PS-0K and PS-1K necessary to appropriately shorten the stop screw (4) of the stud holders on these Welding Pistols.

1		2						3						4

1,5

			SZ06.0593.012.X
1	Stud	3	Counternut
2	Stud holder	4	Stop screw

If other stud diameters are used, different stud holders matching the stud diameters are required.

Set the stud holder as follows:

•Loosen counternut (3)

•Insert stud (1) into the stud holder.

The top edge of the stud flange must project over the front edge of the stud holder by about 1.5 mm.

NOTE

The stud must be inserted until it reaches the stop screw (4).

•Adjust stop screw (4) in the stud holder by rotating movement until the dimension of 1.5 mm between the top edge of the stud flange and the front edge of the stud holder is reached.

•Tighten stop screw (4) with the counternut (3).

4-17

Image 24

Contents PS-3K PS-0K PS-1K PS-3K PS-0K PS-1K GmbH Page Table of Contents Setting the Stud Welding Pistol MaintenanceInitiation Quality controlSpare parts General information Following should be principally observedIntended use Information on the documentation Chapters of Operating InstructionsInformation on Operating Instructions Reaction in the case of malfunctionsDescription of the Stud Welding Pistols Technology of tip ignitionStud Welding Pistol PS-1 Stud Welding Pistol PS-3K PS OM Stud Welding Pistol PS-0KStud Welding Pistol PS-1K Technical data PS-1 PS-3K PS-0K PS-1KSafety instructions Characterisation of references in the Operating InstructionsSafety-conscious working Staff qualification and trainingSafety instructions for the User/Operator Following should be observed prior to initiationSafety measures at the installation site Before starting welding operationsWorking with the Stud Welder Independent retrofitting and spare parts productionNon-permissible operating modes Setting the Stud Welding Pistol Setting the Stud HolderInstalling the stud holder in the Stud Welding Pistol Setting the spring pressure Spring pressureInitiation General viewConnecting the Stud Welding Pistols to the Stud Welder OperationWelding parameters Stud Welder BMS-660-90Stud Welder BMS-690-135 Stud Welder BMS-6H Stud Welder BMS-8HType and scope of testing Quality ControlGeneral information Demands on the companyImplementation of sample taking Normal work testSimplified work test Production of samplesTension test Bending testMaintenance Stud Welding PistolsReplacing components Spare parts list for Stud Welding Pistol PS-1 Spare partsPerspective presentation of Stud Welding Pistol PS-1 Spare parts list for Stud Welding Pistol PS-3K Perspective presentation of Stud Welding Pistol PS-3K Spare parts list for Stud Welding Pistol PS-0K Perspective presentation of Stud Welding Pistol PS-0K Spare parts list for Stud Welding Pistol PS-1K Perspective presentation of Stud Welding Pistol PS-1K Troubleshooting Functional breakdowns Warranty Terms Standards and List of DirectivesHeinz Soyer Bolzenschweißtechnik GmbH