DeWalt 18657 Leveling Table Extensions, Adjusting the Height of the Outfeed Roller

Page 13

LEVELING TABLE EXTENSIONS

For optimum performance, level the table extensions, one of which is shown at (A) Fig. 19, with the planer table. To check and adjust:

Disconnect machine from power source!

1.Place a straight edge (B) Fig. 19 on the planer table with one end of the straight edge extending out over the infeed table extension (A). Check to see if the table extension is level with the planer table on both sides of table extension.

2.If an adjustment is necessary, loosen the locknut

(D) and adjust the stop screw (E) on each side of the table (A). When they are level, tighten the locknut.

B

E

C

A

D

Fig. 19

NOTE: If necessary, loosen the three screws (C), adjust the table extension, and tighten the screws (C).

3.Adjust the opposite side of the table extension (A).

4.Check and adjust other table extension.

ADJUSTING THE HEIGHT OF THE OUTFEED ROLLER

Disconnect machine from power source!

1.	To check and adjust the outfeed roller, make a gauge
	block of hardwood. Follow the dimensions in Fig. 20.
2.	Check the knives to be certain that they were inserted
	correctly. See “REPLACING KNIVES.
3.	Position the gauge block (A) Fig. 21 on the table
	underneath the cutterhead. Insert a 0.020" (.5 mm)
	feeler gauge on top of the gauge block.			4" 101.6mm
4.	Lower the head assembly and rotate the cutterhead
	until one of the knives (B) touches the top of the feeler
	gauge. NOTE: Pull the guard down (G, inset Fig. 21) to
	gain access to the hex hole. Insert the supplied wrench	2"		1/2"	3"
	into the hex hole (F) and turn to rotate the cutterhead.	2"		1/2"	76.2 mm
	into the hex hole (F) and turn to rotate the cutterhead.		51 mm	12.7 mm	76.2 mm
	Tighten the cutterhead lock handle.	Fig. 20			4"
					101.6 mm

5.Remove the feeler gauge and move the gauge block

(A) Fig. 22 under one end of the outfeed roller (C). The bottom of the outfeed roller should touch the

gauge block.

1/4" 6.4 mm

top of the

6.To adjust the outfeed roller, loosen the locknut (D) Fig. 22 and use a hex wrench to turn the adjusting screw (E) until outfeed roller touches the gauge block (A). Tighten the locknut.

7.Repeat this adjustment on opposite side of the outfeed roller.

F

G

B

A

C

A

D

E

Fig. 21

Fig. 22

13 - English

Image 13

Contents 22-580 Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are DOING, and USE General Safety RulesRefer to them often and use them to instruct others Additional Specific Safety RulesMotor Specifications Power ConnectionsGrounding Instructions Functional Description Carton ContentsAssembly Tools Required AssemblyAssembly Time Estimate Lowering the Extension Tables Cutterhead Adjustment HandleCutterhead Lock Handle Operation Locking the Switch in the OFF PositionFastening Planer to Supporting Surface Cutterhead Lock Adjusting the Head AssemblyScale and Pointer Speed ControlBlade Zero Indicator Adjustable Indexing RingBlade zero indicator marks exactly where Do not plane with the blade zero indicator engagedDisconnect machine from power source Adjusting the Height of the Outfeed RollerLeveling Table Extensions Operating Hints Machine USE Recommended Depth of CUTKnife Transfer Tool Storage Wrench Storage TroubleshootingCarrying Handles Stock Transfer BARReplacing Knives MaintenanceBrush Inspection and Replacement Lubrication Cleaning Infeed and Outfeed RollersLubricating the Bearing Blocks Accessories ServiceWarranty Mesures DE Sécurité Définitions LES Instructions Importantes DE SureteLA Proposition DE Californie Lutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Directives Règles Spécifiques Additionnelles DE SûretéSpécifications DU Moteur Raccordements ÉlectriquesGrounding Instructions Instructions DE Mise À LA Terre Contenus DE Boite Description FonctionnelleCordon DE Rallonge AVANT-PROPOSOutils Nécessaires Pour L’ASSEMBLAGE AssemblageDurée Estimée Pour L’ASSEMBLAGE Poignee DE Verrouillage DU PORTE-LAME Abaissement DES Tables a RallongesPoignee DE Réglage DU PORTE-LAME Fixation DE LA Raboteuse a LA Face D’APPUI FonctionnementDémarrage ET Arrêt DE LA Raboteuse Verrouillage DE L’INTERRUPTEUR EN Position D’ARRETRéglage DE L’ENSEMBLE DE Tete Commande DE VitesseVerrouillage DU PORTE-LAME Echelle ET PointeurIndicateur DE Zéro DE LA Lame Anneau DE Guidage RéglableMise a Niveau DES Rallonges DE Table Débrancher la machine de la source d’alimentationSection « Remplacement DES Couteaux » Profondeur DE Coupe RecommandéeReglage DE LA Hauteur DU Cylindre DE Sortie Rangement DE L’OUTIL DE Transfert DE Couteau Conseils D’UTILISATIONRangement DE LA CLÉ Poignees DE TransportDepannage Entretien Remplacement DES CouteauxInspection ET Remplacement DU Balais Lubrifier LES Corps DE Palier LubrificationNettoyer LES Cylindres D’AMENAGE ET DE Sortie Démarrage Impossible Garder LA Machine PropreLubrification ET Protection Contre LA Rouille Pièces DE RechangeGarantie AccessoiriesInstrucciones DE Seguridad Importantes Ww.powertoolinstitute.orgPautas DE SEGURIDAD/DEFINICIONES Proposición DE CaliforniaNormas Generales DE Seguridad Guarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadEspecificaciones DEL Motor Conexiones a LA Fuente DE AlimentaciónInstrucciones DE Conexión a Tierra Contenido DE Carton Descripción FuncionalCordones DE Extensión PrologoHerramientas DE Ensamblaje Requeridas EnsamblajeEstimación DEL Tiempo DE Ensamblaje Bajada DE LAS Mesas DE Extensión Bloqueo DEL Interruptor EN LA Posición DE Apagado OperaciónCierre DEL Cabezal Portacuchillas Ajuste DEL Conjunto DEL CabezalEscala E Indicador Control DE VelocidadAnillo DE Indexación Ajustable Tope DE Profundidad DE Gama CompletaIndicador DE Cero DE LA Hoja Ajuste DE LA Altura DEL Rodillo DE Avance DE Salida Nivelación DE LAS Extensiones DE LA MesaDesconecte la herramienta de la fuente de alimentación Consejos DE Utilización Utilizar LA Maquina Profundidad DE Corte RecomendadaAlmacenaje DE LA Llave Localizacion DE Fallas MantenimientoMangos DE Transporte Barra DE Transferencia DEL MaterialEspañol Lubricación Inspección Y Reemplazo DE LAS EscobillasLubricar EL Cojinete Bloquea Garantia ServicioDelta Machinery Highway 45 North Jackson, TN 800