Miller Electric manual mm Open tension arm, Cally live when gun, Wire, Tools Needed OM-1589

Page 25

3-14. Threading Welding Wire Through Feeder (Continued)

Hold wire tightly to keep it from unraveling.

6 in (150 mm)

Open tension arm.

Pull and hold wire; cut off end.

	Welding wire is electri-
	cally live when gun
	trigger is used to jog
	wire.
Thread wire thru inlet guide, along drive roll groove, and into wire con-	Lay wire conduit out straight. Remove wire conduit
duit. Close tension arm. Adjust tension as follows: grasp spool with	from rear of gun. Press Jog button until about 10 in
one hand, press Jog switch, and turn thumbnut clockwise until motor	(254 mm) of wire is sticking out of conduit.
stalls when Jog switch is pressed. Back thumbnut off slightly.

Open pressure roll assembly. Insert wire thru conduit opening in rear of gun, past drive roll groove, and out contact tip. When wire conduit is seated in rear of gun, tighten screw to secure. Close pressure roll assembly.

WOOD
Feed wire to check drive roll pres-	Cut off wire. Reinstall gun cover. Close
sure. If necessary, adjust pres-	and latch wire feeder doors.
sure adjustment knob in gun.

Tools Needed:

Ref. 800 944

OM-1589 Page 19

Image 25

Contents Processes OM-1589Description From Miller to You Table of Contents 10-2 10-111-1 11-2Standards DirectivesDeccon 11/96 Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explo- sion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killPrincipal Safety Standards About Pacemakers EMF Information− Consignes DE Securite − Lire Avant Utilisation Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionDES Pièces Chaudes peuvent pro- voquer des brûlures graves LE Bruit peut affecter l’ouïeLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU’EMPLOI Excessif peut DES Organes Mobiles peuvent provoquer des blessuresInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques − Definitions Disconnect input plug or power before working on machineDrive rolls can injure fingers Keep your head out of the fumesManufacturer’s Rating Label for CE Products Symbols And DefinitionsSpecifications − InstallationType of Input Welding Power Wire Feed Welding Overall WeightTools Needed 16, 5/8, 11/16, 3/4 Typical Water-Cooled System ConnectionsPin Plug Information Rear Panel ConnectionsPin Pin Information Internal Connections for Air-Cooled Gun Internal Connections for Water-Cooled GunTions directly to gun hose To gun partsTools Needed 11/16, 1-1/8 Water-Cooled Model Shown Front Panel Connections for GunWater-Cooled Guns Air-Cooled GunSetting Torque Switch Adjusting Contact Tip PositionTorque Switch Removing Top Cover of GunWire Spool Top Cover Pressure Roll Assembly Gun Contact Tip Installing Wire SpoolHub Tension Adjustment Threading Welding Wire Through FeederWire Cally live when gun150 mm Open tension arm Tools Needed OM-1589Operational Terms − OperationPulse Welding Terms Front Panel Controls Gun Controls Side and Rear Panel ControlsSequence Parameters in a Program − Setting Sequence ParametersSelecting Dual Schedule Pair − Setting Dual Schedule ParametersDual Schedule Switch Diagrams − Using the Optional Data CardData Card Terms AdapterWire feeder memory Installing Data CardCard Displays 3 seconds and the 8 programsSystem Setup Display Parameters − System SetupDisplay Setting Program 1 − Aluminum − Standard Pulse Welding ProgramsProgram 2 − Aluminum Program 4 − Aluminum Program 3 − AluminumGas 100% Argon / 20-Max CFH 24.5 435 325Program 6 − Aluminum Program 5 − Aluminum23.2 490 290 Gas 100% Argon / 20-45 CFHProgram 7 − Aluminum Program 8 Aluminum875 485 140 250 31.5 820 470 135 240 30.9 765 450 21.2 160 305 19.6 105 300 22.2Teach Points Explained − Teach PointsRedefining IPM Teach Point Redefining Teach PointsRedefining Pulse Parameters Serial Number Wire Feeder Date Program Number Wire Size/TypeFlowrate CFHL/min PositiveRoutine Maintenance − Maintenance and TroubleshootingFeeder Drive Assembly Maintenance Disconnect power before maintainingChanging Gun Contact Tip and Liner Gun Drive Assembly MaintenanceRemoving Water-Cooled Contact Tip Adapter Removing Air-Cooled Contact Tip AdapterBarrel Extension Remove as shownRelease Trigger Error Display Error DisplaysNo Volt Sensed Error Display E s s OM-1589 Using Self TestDisconnect power before troubleshooting TroubleshootingFilter, and clean fittings Trouble RemedyOM-1589 Circuit Diagram − Electrical Diagram184 771-A Circuit Diagram For Gun OM-1589 List Main AssemblyPLG1 PLG81 Motor & Wire Drive -1 Item Motor & Wire DrivePanel, Front w/Components -1 Item Panel, Front w/ComponentsPC40 PC60Barrel Assembly 137 Barrel ASSEMBLY, water cooled XRM-15W & 30W models Includes Item 34 33 13−5 48Fig133 Item Dia Part Mkgs Description Quantity Your distributor also gives ServiceSupport Step of the wayTo locate distributor nearest you call 1-800-4-A-Miller Miller Electric Mfg. Co