Miller Electric XMS 4000 manual Dia Part Description Quantity Mkgs

Page 35

Item

Dia.

Part

Description

Quantity

 

No.

Mkgs.

No.

 

 

 

 

Figure 7-1. Unit Outer Assembly

 

 

 

 

 

 

 

. . .

1

. . . . . . . . . . .

V57038158

. . . Turntable

. . . 1

. . .

2

. . . . . . . . . .

+V17031141

. . . Cover

. . . 1

. . .

3

. . . . . . . . . .

+V56005145

. . . Cylinder support

. . . 1

. . .

4

. . . . . . . . . . .

. 000207235

. . . Label, warning, tilting

. . . 1

. . .

5

. . . . . . . . . . .

V56014164

. . . Cylinder, security

. . . 1

. . .

6

. . . . . . . . . . .

. 000207290

. . . Label, warning, cooling unit

. . . 1

. . .

7

. . . . . . . . . . .

V56142088

. . . Label, rating plate

. . . 1

. . .

8

. . . . . . . . . . .

. . 56043030

. . . Cap

. . . 2

. . .

9

. . . . . . . . . . .

. 056054067

. . . Wheels, rubber, 250 mm dia

. . . 2

. . . 10

. . . . . . . . . . .

. 156009066

. . . Washer, 21 mm dia

. . . 2

. . . 11

. . . . . . . . . . .

. 156012013

. . . Wheels, pivot

. . . 1

. . . 12

. . . . . . . . . .

+V16122151

. . . Expanded plate dx

. . . 1

. . . 13

. . . . . . . . . . .

. 000207233

. . . Label, warning

. . . 1

. . . 14 . . . . . . . . . . . . . . . . . . . 056054074 . . . Wheels, pivoting 100 mm dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

. . . 15 . . . . . . . . . . . . . . . . . . V56142156 . . . Label, logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 16 . . . . . . . . . . . . . . . . . . . 000208154 . . . Panel, front, plastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 17 . . . . . . . . . . . . . . . . . . . 000207233 . . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 18 . . . . . . . . . . . . . . . . . . . 000207291 . . . Label, warning, input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 19 . . . . . . . . . . . . . . . . . +V16122152 . . . Expanded plate sx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

+When ordering a component originally displaying a precautionary label, the label should also be ordered.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-224 043 Page 31

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Xmsr From Miller to You Table of Contents Declaration of Conformity for European Community CE Products Arc Welding Hazards Symbol UsageMarks a special safety message Magnetic Fields can affect pacemakers ARC Rays can burn eyes and skinFire or Explosion hazard California Proposition 65 WarningsAbout Pacemakers Principal Safety StandardsEMF Information Manufacturer’s Warning Label Definitions − Definitions60 s 100 h. std I1eff Manufacturer’s Rating Labels Symbols And DefinitionsI1max Duty Cycle And Overheating − InstallationSpecifications Volt-Ampere Curves Remove wire spool Turntable ScrewLocation Dimensions and WeightMovement Do not move or operate unit where it could tip Selecting a Location120 m Weld Output Terminals And Selecting Cable SizesRemote 7 Receptacle Information TIG And Stick Only ARC Welding can cause Electromagnetic InterferenceFilling Coolant Tank Circuit Breakers= GND/PE Electrical Service GuideConnecting Input Power 50/60 Hz Three PhaseFront Panel Controls − OperationWelding Process Selection Switching On the Unit and Recalling Factory ParametersBe aware that the wire type selection is Gas Selection in Synergic MIG or Synergic Pulsed MIG Welding Trigger Mode Selection TIG and Stick OnlySetting Menu Type TIG and Stick only Setup Push Button And Advanced ProgrammingSelecting Manual MIG Welding During SettingSetting Cooler Status Preparing Unit For MIG WeldingDuring Synergic MIG Welding Setting Cooler Status see SectionSelecting Synergic MIG Welding Selecting Synergic Pulsed MIG Welding Preparing Unit For TIG Welding Setting Initial And Final Amperage only in Menu FullSetting Postflow only in Menu Full Setting Cooler Status only in Menu FullPreparing Unit For Stick Welding TIG Lift-Arc WeldingMonths − Maintenance & TroubleshootingHelp Displays Do not remove case when blowing out inside of unitBlowing Out Inside Of Unit Is displayed TroubleshootingSoftware problems OM-224 043 − Electrical Diagram Unit Outer Assembly − Parts ListDia Part Description Quantity Mkgs Unit Main Assembly CR5,6,R1 Page Effective January 1 ITW Welding Products Italy S.r.l. Via Privata Iseo, 6/E Owner’s Record
Top Page Image Contents