Miller Electric XMS 4000 manual Declaration of Conformity for European Community CE Products

Page 4

Declaration of Conformity for

European Community (CE) Products

NOTE

This information is provided for units with CE certification (see rating label on unit).

Manufacturer:	European Contact:
ITW Welding Products Italy S.r.l.	Mr. Danilo Fedolfi,
Via Privata Iseo 6/E	Managing Director
20098 San Giuliano	ITW Welding Products Italy S.r.l.
Milanese, Italy	Via Privata Iseo 6/E
Phone: 39(02)98290-1	20098 San Giuliano
	Milanese, Italy
	Phone: 39(02)98290-1
	Fax: 39(02)98290203

European Contact Signature:

Declares that this product: XMS 4000

conforms to the following Directives and Standards:

Directives

Electromagnetic compatibility Directives: 89/336/EEC, 92/31/EEC

Low Voltage Directive: 73/23/EEC

Machinery Directives: 89/392/EEC

and their amendments 91/368/EEC, 92/31/CEE, 133/04, 93/68/EEC

Standards

Electromagnetic compatibility (EMC) Product standard for arc welding equipment: EN50199: Augusst1995

Safety Requirements for Arc Welding Equipment part 1: EN 60974-1: 1990

Degrees of Protection provided by Enclosures (IP code): IEC 529: 1989

Insulation coordination for equipment within low-voltage systems:

Part 1: Principles, requirements and tests: IEC 664-1: 1992

The product technical file is maintained by the responsible Business Unit(s) located at the manufacturing facility.

dec_stat_Milan_6/05

Image 4

Contents Xmsr From Miller to You Table of Contents Declaration of Conformity for European Community CE Products Marks a special safety message Symbol UsageArc Welding Hazards ARC Rays can burn eyes and skin Magnetic Fields can affect pacemakersCalifornia Proposition 65 Warnings Fire or Explosion hazardEMF Information Principal Safety StandardsAbout Pacemakers − Definitions Manufacturer’s Warning Label Definitions60 s 100 h. std I1max Manufacturer’s Rating Labels Symbols And DefinitionsI1eff Specifications − InstallationDuty Cycle And Overheating Remove wire spool Turntable Screw Volt-Ampere CurvesDimensions and Weight Movement Do not move or operate unit where it could tipSelecting a Location LocationWeld Output Terminals And Selecting Cable Sizes Remote 7 Receptacle Information TIG And Stick OnlyARC Welding can cause Electromagnetic Interference 120 mCircuit Breakers Filling Coolant TankElectrical Service Guide Connecting Input Power50/60 Hz Three Phase = GND/PE− Operation Front Panel ControlsSwitching On the Unit and Recalling Factory Parameters Welding Process SelectionBe aware that the wire type selection is Trigger Mode Selection TIG and Stick Only Gas Selection in Synergic MIG or Synergic Pulsed MIG WeldingSetup Push Button And Advanced Programming Setting Menu Type TIG and Stick onlyDuring Setting Setting Cooler StatusPreparing Unit For MIG Welding Selecting Manual MIG WeldingSelecting Synergic MIG Welding Setting Cooler Status see SectionDuring Synergic MIG Welding Selecting Synergic Pulsed MIG Welding Setting Initial And Final Amperage only in Menu Full Setting Postflow only in Menu FullSetting Cooler Status only in Menu Full Preparing Unit For TIG WeldingTIG Lift-Arc Welding Preparing Unit For Stick Welding− Maintenance & Troubleshooting MonthsBlowing Out Inside Of Unit Do not remove case when blowing out inside of unitHelp Displays Software problems TroubleshootingIs displayed OM-224 043 − Electrical Diagram − Parts List Unit Outer AssemblyDia Part Description Quantity Mkgs Unit Main Assembly CR5,6,R1 Page Effective January 1 Owner’s Record ITW Welding Products Italy S.r.l. Via Privata Iseo, 6/E