Bosch Power Tools CAG180BL, CAG180BN Assembly, Keys Screw Notches, Lock NUT and Backing Flange

Page 10
! WARNING

BM 2610034439 04-14_CAG180 4/1/14 7:26 AM Page 10

Functional Description and Specifications (Continued)

Model number

CAG180

* Max. type 27 grinding wheels

4 1/2" Dia.

* Max. type 1A and 27A cutting wheel

4 1/2" Dia.

* Max. flap disc

4 1/2" Dia.

Accessory speed rating must be equal to or greater than the tool’s speed rating. Do not

exceed the recommended wheel diameter.

NOTE: Not recommended for use with type 11 cup wheels.

* NOTE: For tool specifications refer to the nameplate on your tool.

Assembly

WHEEL GUARD INSTALLATION Wheel guard must be attached when using disc

grinding or cutting wheels. Always keep wheel guard between you and your work while grinding or cutting.

The position of the guard can be adjusted to accommodate the operation being performed.

To attach wheel guard, DISCONNECT battery pack from tool.

Position guard on spindle neck so that the notches on guard line up with the keys on the spindle neck (Fig. 2).

Rotate guard either direction to desired position, and tighten screw with the hex wrench provided to secure guard in place.

notches on guard line up with the keys on the spindle neck, and lift guard off the spindle neck (Fig. 2).

FIG. 2

KEYS

SCREW

NOTCHES

TO REMOVE GUARD: Loosen screw with the hex wrench provided, rotate guard until the

LOCK NUT AND BACKING FLANGE

Your tool is equipped with a threaded spindle for mounting accessories. Always use the supplied lock nut (and backing flange) that has same thread size as spindle.

VIBRATION CONTROL SIDE HANDLE

(Optional Accessory)

The side handle is used to control and balance the tool. The handle must be threaded into the front housing on either side of the tool, depending on personal preference and comfort. Use the side handle for safe control and ease of operation (Fig. 1).

OPTIONAL HAND GUARD

(Optional Accessory)

The hand guard is to be used with backing pads, sanding discs and wire brushes to keep fingers and hand away from work surface, sharp edges, burrs and debris. When using the optional hand guard accessory insert side handle through hole in guard and then thread into housing (Fig. 1).

Ensure that hand guard is positioned between hand and backing pad, sanding disc or wire brush.

-10-

Image 10
Contents See Leer antes de usarVer la página Electrical safety General Power Tool Safety WarningsWork area safety Personal safetyBattery tool use and care Power Tool-Specific Safety WarningsService Kickback and Related Warnings Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Wire Brushing OperationsSome dust created by power Symbols Symbol Name Designation/ExplanationSymbols Battery Packs/Chargers Functional Description and SpecificationsOptional Accessory Cordless Angle GrinderLock NUT and Backing Flange AssemblyKeys Screw Notches Vibration Control Side HandleSpindle Type 1A Wheel Guard Backing Flange Spindle Type Wheel Guard Backing Flange GrindingStraight Grinding Wheels Type 1A ISO41Backing PAD To Install Backing PAD Sanding DiscWire Brush SpindleOperating Instructions Grinding OperationsCutting MASONRy Cutting MetalSelecting Sanding Disc Wire Brush Operations Inserting and Releasing BATTERy Pack Accessories MaintenanceCleaning Sécurité du lieu de travail Sécurité électriqueUtilisation et entretien des outils à piles Utilisation et entretien des outils ÉlectroportatifsEntretien Avertissements sur les rebonds et effets associés Rebondir sur votre main Opérations de ponçage Opérations de brossage métalliqueSymboles Symbole Nom Désignation/ExplicationSymboles suite BLOC-PILES Description fonctionnelle et spécificationsRectifieuse d’angle sans fil Bloc-piles/chargeursPose DU Protecteur DE Meule Description fonctionnelle et spécifications suiteAssemblage Ergots VIS Encoches Écrou DE Blocage ET Bride DappuiArbre Protecteur DE Meule Type 1A Bride Ensemble DE Meule a DisqueArbre Meule DE Type Bride Dappui DappuiEnsemble DE Brosse Métallique Ensemble Daccessoires DE Poncage Disque D’APPUIArbre Brosse Métallique Disque ’APPUI Disque DE Poncage Ensemble DE Brosse Métallique À TouretConsignes de fonctionnement Travaux de meulageCoupe DE Maçonnerie Travaux de ponçageCoupe DES Métaux Choix DES Disques DE PonçageTravaux à la brosse métallique Insertion ET Retrait DU BLOC-PILES Entretien AccessoiresNettoyage Seguridad eléctrica Seguridad del área de trabajoSeguridad personal Uso y cuidado de las herramientas Alimentadas por baterías MecánicasServicio de ajustes y reparaciones Retroceso y advertencias relacionadas Abrasivas Le plomb provenant des peintures à base de plomb Símbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Rueda DE Descripción funcional y especificacionesAmoladora sin cordón Protector DE LA ManoDientes Tornillo Muescas EnsamblajeProtector DE LA Mano Opcional Ruedas Abrasivas DE Tipo 1 Para Amoladoras Rectas Husillo Protector DE LA Muela Tipo 1A Pestaña DE SoportePara Instalar LA Zapata DE Soporte Y Zapata DE SoporteHusillo Disco DE LijarSeleccion DE Ruedas DE Amolar Instrucciones de funcionamientoOperación de amolado Ruedas DE Amolar DE DiscoCorte DE Mampostería Operaciones de lijadoCorte DE Metal Seleccion DEL Disco DE LijarOperaciones con cepillos de alambre Introducción Y Suelta DEL Paquete DE Baterías Servicio MantenimientoAccesorios LimpiezaBM 2610034439 04-14CAG180 4/1/14 726 AM BM 2610034439 04-14CAG180 4/1/14 726 AM 2610034439