Bosch Power Tools 1613AEVS Maintenance, Accessories, Tool Lubrication, Carbon Brushes, Bearings

Page 17

BM 2610943371 07-06.qxp 7/24/06 9:03 AM Page 17

Maintenance

Service

Preventive maintenance ! WARNING performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Autho-

rized Bosch Service Station.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement brushes specially designed for your tool should be used.

BEARINGS

After about 300-400 hours of operation, or at every second brush change, the bearings

should be replaced at Bosch Factory Service Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.

Cleaning

To avoid accidents always ! WARNING disconnect the tool from

the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

Certain cleaning agents ! CAUTION and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

!WARNING If an extension cord is necessary, a cord with

adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

 

 

 

 

 

 

 

 

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

25

50

100

150

15

30

60

120

 

3-6

 

 

 

 

 

 

 

 

18

16

16

14

0.75

0.75

1.5

2.5

6-8

18

16

14

12

0.75

1.0

2.5

4.0

8-10

18

16

14

12

0.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

—

12-16

14

12

—

—

—

—

—

—

 

 

 

 

 

 

 

 

 

1/4” Collet Chuck *

Dust Extraction Hood

Templet Guide Adapter *

1/2” Collet Chuck *

for Edge Forming **

Templet Guides **

24 mm Collet Nut Wrench *

Adapter for Various

Centering Cone **

3/8” Collet Chuck **

Vacuum Hoses *

Router Table **

8 mm Collet Chuck **

Vacuum Hose **

(*= standard equipment)

Dust Extraction Hood *

Deluxe Router Guide **

 

Router Bits **

(**= optional accessories)

-17-

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Ver la página Read Before UsingKeep your work area clean and well lit Power Tool Safety RulesCluttered benches and dark areas invite accidents Distractions can cause you to lose controlProtruding cutting bit may cause tool to jump Safety Rules for RoutersNecessary to stand on the table or its stand to reach them Safety Rules for Router TableOthers may create a hazard Symbols ON/OFF Trigger Switch Functional Description and SpecificationsRouter Measures reduce the risk of starting the tool accidentallyInstalling a Router BIT AssemblySelecting Bits Removing the Router BITOperating Instructions Depth ROD and Turret Afterlock Fine AdjustmentFine Adjustment Knob Indicator Index Marker Soft Start Feature Trigger Switch and LOCK-ON ButtonDial Setting RPM Application Electronic Variable Speed ControlStart Here Feeding the RouterRouter Feed Rate of FeedAttaching Dust Extraction Hood Dust Collection While Edge FormingRouter SUB-BASE Workpiece Edgedust Extraction Hood Screw Dust Extraction HoodCentering the SUB-BASE Templet Guides Centering Cone optional accessoryGuiding the Router Board Guide Feed Direction Securely Clamp BoardGuide Adapter Not included, available as accessoryTemplet Guide Offset WorkpieceOperation in Router Table Accessories MaintenanceTool Lubrication Carbon BrushesConservez CES Instructions Règles de Sécurité GénéralesBlessures graves La réparation des outils électriques doit être confiée Règles de sécurité concernant les toupiesLe plomb provenant des peintures à base de plomb Consignes de sécurité pour table de toupillageBM 2610943371 07-06.qxp 7/24/06 903 AM Symboles Défonceuse Description fonctionnelle et spécificationsGâchette MARCHE/ARRÊT Ouïes DE Ventilation Poignée Droite Bouton DEAssemblage Consignes d’utilisation Passe étant réalisée avec la tige de profondeur abaissée Tige ET Tourelle DE ProfondeurRéglage FIN Afterlock Bouton DE Réglage FIN Index DESUR Marche Commande Électronique DE Variation DE VitesseSystème DE Démarrage Progressif Cadran DE Réglage DE VitesseCommen CER ICI Avance DE LA DéfonceuseSens DE FERL’AVANCE Vitesse D’AVANCE Moulurage DE ChantsRamassage DE Poussière Lors DU Moulurage DE Chants ’emploi de l’outil avec ces accessoiresFixation DU Capuchon D’EXTRACTION DE Poussière VIS= Trous DE VIS Noyées M4 Centrage DE LA SOUS-EMBASE ET DES= Trous DE VIS À Tête Cylindrique M4 DE LA DéfonceuseAdaptateur DE Guide DE Gabarit Levier DE Déblocage DU Guides DE GabaritDéport Pièce Embase Coupe VIS MoletéeUtilisation avec la table de toupillage Entretien AccessoiresLubrification DE L’OUTIL Balais OU CharbonsPersonales graves Normas de seguridad para herramientas mecánicasServicio Normas de seguridad para fresadorasInstrucciones de seguridad para la mesa de fresadora BM 2610943371 07-06.qxp 7/24/06 903 AM De Ni-Cd SímbolosCon aislamiento doble Fresadoras Descripción funcional y especificacionesRiesgo de arrancar la herramienta accidentalmente SubbaseSelección DE Brocas EnsamblajeRemoción DE LA Broca DE Fresadora Cuidado DEL Mandril PortaherramientaInstrucciones de funcionamiento Pomo DE Ajuste Fino Indicador Marcador DE Índice Varilla DE Profundidad Y TorretaAjuste Fino Posfijación Dispositivo DE Arranque Suave Interruptor Gatillo Y Botón DE Fijación EN EncendidoDial DE Control DE Velocidad Posición DEL DialVelocidad DE Avance Avance DE LA FresadoraComience Aquí Conformado DE BordesSubbase DE LA Fresadora Borde DE LA Colocación DE LA Cubierta DE Extracción DE PolvoTrabajo TornilloCono DE Centrado accesorio opcional Centrado DE LA Subbase Y LAS Guías DE Plantilla= Agujeros Para Tornillos DE Cabeza Troncocónica M4 Guiado DE LA FresadoraGuía DE Plantilla Adaptador DE Guías DE PlantillaBroca DE Guía DEUtilización en la mesa de fresadora Accesorios MantenimientoLubricacion DE LAS Herramientas Escobillas DE CarbonBM 2610943371 07-06.qxp 7/24/06 903 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools

1613AEVS specifications

The Bosch Power Tools 1613AEVS is a versatile and powerful fixed-base router designed for professional woodworkers and DIY enthusiasts alike. Renowned for its outstanding performance and durability, this router is a valuable tool for any workshop. Its powerful 2.0 HP motor delivers impressive routing capabilities, making it suitable for a wide range of tasks, from edge profiling to mortising and decorative work.

One of the key features of the Bosch 1613AEVS is its variable speed control. This allows users to adjust the speed from 8,000 to 25,000 RPM, providing optimal performance for various routing applications. Whether working with softwoods or hardwoods, users can select the perfect speed to achieve clean, precise cuts while minimizing the risk of damage to the material.

The router also boasts a soft-start function, which gently ramps up the motor speed, allowing for smoother operation and reducing the potential for tool kickback. This is especially beneficial for beginners or those working with delicate materials. Additionally, the Bosch 1613AEVS is equipped with a constant response circuit that maintains speed under load, ensuring consistent results even when cutting tougher materials.

Another noteworthy characteristic of the 1613AEVS is its ergonomic design. The router features a comfortable grip and well-balanced body that reduces user fatigue during extended use. The integrated spindle lock allows for easy bit changes, while the included adjustable T-handle provides enhanced control and stability when routing.

For enhanced precision, the Bosch 1613AEVS comes with a transparent base that provides a clear line of sight to the workpiece. It also incorporates a dust extraction port that connects to standard vacuums, helping to keep the work area clean and free from debris.

In summary, the Bosch Power Tools 1613AEVS combines power, versatility, and user-friendly features. With its robust motor, variable speed control, soft-start technology, and ergonomic design, this router is well-suited for both professional and hobbyist woodworkers. Whether you're crafting intricate furniture pieces or simple decorative edges, the 1613AEVS is a reliable tool that delivers accuracy and performance.
Top Page Image Contents