Omega Vehicle Security FPU5-MT-220, FPU5-MT-110 Getting Started, Attaching the Pump, Introduction

Page 20

3	Getting Started
3

3.1Attaching the Pump

3.1.1Introduction

There are five possible mounting configurations for using the peristaltic pump motor. Table 3-1 describes these mounting configurations.

Table 3-1. Pump Motor Mounting Configurations

Number of Pumps on	Number of Pumps on	Reference Section
Left Side	Right Side
1	0	3.1.2

0	1	3.1.2

2	0	3.1.3

0	2	3.1.3

1	1	3.1.2

NOTE

Your pump motor is equipped with a safety cover for whichever side of the motor is not being used.

You must remove the safety cover before attempting to attach pump(s) to the side.

3-1

Image 20

Contents User’s Guide Servicing North America Unpacking Instructions Table of Peristaltic Pump Motor Chapter Specifications Spare Parts and Accessories 10-1 Peristaltic Pump MotorPeristaltic Pump Motor Index RPMIndex III Description FeaturesIntroduction Introduction Parts of the Pump Motor Front ViewFront View Description FunctionLeft Side View Left Side ViewRight Side View Right Side ViewMembrane Keypad and Display Membrane Keypad DetailMembrane Keypad Details cont’d Flow Rate keyRear View Rear ViewUP and Down Arrow Keys Scrolling Limits Rear View cont’d Language ButtonParts of the Pump Motor Pump Motor Mounting Configurations Number of Pumps on Getting StartedAttaching the Pump IntroductionAttaching a Single Pump Directly to the Motor Refer to Figures 3-1 throughStacking Two Pumps on One Side of the Motor Placing the Second Pump on Top of the First PumpLoading the Tubing Selecting TubingTubing Life See .2 to set the pumping direction Getting Started Turning on the Power Using the ON/OFF SwitchStopped Display Mode Introduction to the Two Display ModesRunning Display Mode Stopped vs. Running Display ModesDisplaying Pump Messages in Five Different Languages Stopped Display ModeOperating the Pump Motor English French Spanish German Italian Régler LA QTÉDefining the Direction of Pumping Selecting the Tubing Inner Diameter Left Pump Right PumpTube Inner Diameters English Metric Priming the Tubing Calibrating the TubingOperating the Pump Motor in the Stopped Display Mode Tips for Optimum Calibration Accuracy Measuring the Temperature of a Fluid Preparing for Pumping in a Specific ModeTotal Volume Pumping in the RPM Mode Running Display ModeRPM Mode Shows the range of the RPM numbers you can work with RPM Mode Cont’d Flow Rate Mode Pumping in the Flow Rate ModeShows the ranges allowed for the various tubing sizes Flow Rate Ranges cont’d Display Xxx mL/min Flow Rate Mode Flow Rate Mode Time Mode Pumping in the Time ModeTime Range Display Xxxxxx Time Mode Time Mode Total Volume Mode Block Diagram Pumping in the Total Volume ModePumping in the Total Volume Mode Total Volume RangeOperating the Pump Motor in the Running Display Mode Total Volume Mode Cont’d Auxiliary Out Remote Monitor Preventing Tubing from Moving During Pump OperationOther Pumping Options 500Ω LED Auxiliary In Remote Start/StopTroubleshooting Guide Display Error MessagesError Message Problem SolutionError Message Running Display Mode and try to select the command againLocked Rotor? Overcurrent Press the Total Volume key Short Circuit? Error Message Other Pumping Problems Stopped Display Mode and refer to SectionProblem Solution Another pump, if necessary Troubleshooting Guide Design Solution MaintenanceTechnical Details Theory of OperationTechnical Details Specifications Calibration AccuracyAverage Flow Rates MotorTubing Materials SpeedAverage Tubing Life ⁄32 300 ⁄16 250 100 ML Per Revolution Specifications Spare Parts and Accessories AccessoriesSpare Parts Part Number DescriptionAccessories cont’d Peristatic Pump 10-4 WARRANTY/DISCLAIMER