Honeywell LYNXR-EN, LYNXR Series setup guide System Status Report Codes, Restore Report Codes

Page 21

 

 

Data Field Descriptions

 

SYSTEM STATUS REPORT CODES (✻59–✻68)

 

 

✻59

Exit Error Report Code

If the system is armed and an entry/exit or interior zone is still open

 

(See notes above)

after the exit delay time has expired, an alarm will sound at the

 

 

keypad and external sounder. If the system is disarmed before the

 

 

 

 

 

 

end of the entry delay that immediately follows, the alarm sounding

 

 

 

will stop and no message will be sent to the central station. The

 

 

 

keypad will display “CA (CANCELED ALARM).”

 

 

 

If the system is not disarmed before the end of the entry delay

 

 

 

mentioned above, and an entry/exit or interior zone is still open, an

 

 

 

“exit alarm” message will be sent to the central station if an Exit

 

 

 

Error report code is selected in this field. The keypad will display

 

 

 

“EA (EXIT ALARM),” and the alarm sounding will continue until

 

 

 

the system is disarmed (or timeout occurs).

 

 

 

An Exit Alarm condition will also result if a fault occurs in an exit or

 

 

 

interior zone within 2 minutes following the end of the exit delay,

 

 

 

and an “Exit Alarm” message will be sent to the central station.

 

 

 

If Contact ID® format has been programmed, the message will

 

 

 

contain the zone number and error code 374 (Trouble–Exit Error). If

 

 

 

4+2 format is used, the digit entered in this field will be sent

 

 

 

followed by the second digit of the programmed alarm code for that

 

 

 

zone. If 3+1 or 4+1 format is used, only the digit entered in this field

 

 

 

will be sent. This message will go to the primary phone no. Under

 

 

 

any of these conditions, no restore message will be sent.

 

 

 

If “0” is entered in this field, no special message will be sent, only

 

 

 

the regular alarm and alarm restore code for the zone.

 

 

 

 

 

✻60

Trouble Report Code

This will be sent if a zone goes into trouble.

 

(See notes above)

 

 

 

 

 

✻61

Bypass Report Code

This will be sent when a zone is manually bypassed.

 

(See notes above)

 

 

 

 

 

✻62

AC Loss Report Code

Timing of this report is random with up to a 4-hour delay. If AC

 

(See notes above)

restores before the report goes out, there is no AC restore report.

 

 

 

 

✻63

Low Battery Report Code

This will be sent when a low battery condition exists in the system’s

 

(See notes above)

standby battery.

 

 

 

 

✻64

Test Report Code

This is sent periodically to test that the communicator and phone

 

(See notes above)

lines are operational (frequency of report is selected in field ✻51).

 

 

 

 

 

 

 

 

✻65

Open Report Code

This is sent upon disarming of the system. 2nd digit = user number,

 

(See notes above)

if expanded or 4+2 reporting is selected.

 

 

 

 

 

 

 

 

✻66

Arm AWAY/STAY Report Code

This option allows for independent programming of AWAY and

 

(See notes above)

STAY reports. 2nd digit of report is user number if expanded or 4+2

 

 

reporting is selected.

 

 

 

 

 

 

NOTE: OPEN reports are not sent if the associated closing report is

 

 

 

not enabled.

 

 

 

 

 

✻67

RF transmitter Low Batt. Report Code

This is sent in the event that a wireless transmitter low battery

 

(See notes above)

condition exists.

 

 

 

 

✻68

Cancel Report Code

This is sent upon disarming of the system after an alarm condition

 

(See notes above)

was reported.

 

 

 

 

RESTORE REPORT CODES (✻70–✻76)

 

 

✻70

Alarm Restore Report Code, 1st Digit

Sent when the zone that caused an alarm is restored to its non-

 

faulted condition. 2nd digit is automatically sent as the 2nd digit of

 

 

(See notes above)

the zone alarm report code programmed in field ✻56, if expanded or

 

 

 

4+2 reporting is selected.

 

 

 

 

 

✻71

Trouble Restore Report Code

Sent when a trouble in a zone is restored.

 

(See notes above)

 

 

 

 

 

 

 

 

 

✻72

Bypass Restore Report Code

Sent when a zone that has been bypassed is unbypassed.

 

(See notes above)

 

 

 

 

 

 

 

 

 

✻73

AC Restore Report Code

Sent when AC power has been restored after an AC power outage.

 

(See notes above)

 

 

 

 

 

 

 

 

 

✻74

Low Battery Restore Report Code

Sent when a system low battery condition is restored to normal.

 

(See notes above)

 

 

 

 

 

 

 

 

–21–

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Ademco Lynxr Series Security Systems Recommendations For Proper Intrusion Protection Recommendations for Smoke and Heat DetectorsTable of Contents Hardwire zone System FeaturesHour backup Two-way voice communication Speaker phone operationDesktop Mounting Mounting the ControlWiring Connections Wiring OverviewWiring Connections Full Line Seizure Connections This System AC Power and Rechargeable Backup Battery AC Power and Backup Battery75 to 150 feet 150 to 300 feetHours minimum At least 1-hour before battery depletion Hours minimum Approximately 1-hour before battery depletionGeneral Information Installing Wireless ZonesHouse Identification Transmitter SupervisionUsing the Transmitter Sniffer Mode Transmitter Battery LifeEnter Installer code 4112 + # + Go/No Go Test ModeSetting DIP Switches on the 5800RL and 5827 Transmitters Exiting Program Mode Loading Factory DefaultsMechanics of Programming General Programming InformationType Zone Response Type DefinitionsZone Not Used Type Entry/Exit Burglary #1 Type 02 Entry/Exit Burglary #25806/5807/5808 Data Field Descriptions Defaults where applicable are Indicated in TextFields 43 Dialer ProgrammingPhone System Select Follow Me Reminder Phone NumberReport Format for Primary/Secondary Split/Dual ReportingSystem Status and Restore Report Codes Programming 59 76 System Status Report Codes Restore Report CodesRestore Report Codes Download Information 94 Enhanced Zone Programming Mode Enabling the Wireless DialerDevice Programming Menu Mode Zone Lists for Menu ModeWireless Dialer Setup Enabling the 5842 Wireless DialerEnable trouble reports Enable the wireless dialerEnable back-up reporting Response to phone line tamperEnhanced Zone Programming Mode Zone type Zone numberReport code Input typeEnroll mode Delete zone parametersConfirmation Serial number Voice descriptorDescriptor Programming Options Defined Device Programming Menu ModeStart by Event Start by Zone Type or System OperationUpon Restore of a Zone List Programming Powerline Carrier DevicesStop Upon a Zone Type or System OperationProgramming Powerline Carrier DeviceDevice number Device actionZone List Menu Mode Enhanced Sequential Mode 00 = exit Sequential modeEnter the 2-digit zone number = copy the previous serial number entry from the buffer IA LCDelete serial number Assign zone voice descriptors Assign Zone Voice DescriptorsVoice Vocabulary Index Assign Zone Voice DescriptorRecord Custom Voice Descriptors Assign custom voice descriptorsCustom descriptor number Voice Prompt Programming Keypad Functions Voice Prompt ProgrammingFront Basement Back Sliding Second Central Station Account NumberPatio ToenrollPendant Type Template To Enter Expert Programming ModeRemote Programming/Control Downloading Remote Programming InformationEquipment required to download to a system at the premises Remote Programming Advisory Notes System Operation Security CodesPanic Keys Keypad Functions Volume ControlMessage Center Other FunctionsRemote Phone Control Feature Remote Phone Control FeatureSpeaker Phone Operation LYNXR-EN Only Alarm Audio Verification Two-Way Voice Feature Operator CommandsActivation Powerline Carrier Devices e.g. X-10 devices Follow Me System Announcement FeatureExit Error Alarm Displays If programmedFault and Battery Displays Trouble ConditionsOther Displays Testing the System Test ModeArmed System Test Communication Overview System CommunicationReport +1/4+1 Standard +1/4+1 Expanded Contact ID Event CodesS T E M i n c l u d i n g W i r e l e s s Troubleshooting GuideO K E D E T E C T O R N T R O LRead the Instructions PLEASE, before you call Technical Support, be sure youUL Notice This is a Grade a residential system Regulatory Agency StatementsLYNXR-Series Security Controls SpecificationsElectrical CommunicationLYNXR/LYNXR24 Programming Default Tables LYNXR-EN Programming Default Tables Zone ASSIGNMENT/ALARM Report Codes for Table Device Number Start StopEvent System Operation20, 61 IndexExit Delay Serial Number Page Limitations of this Alarm System Limited Warranty System Police With‡K5963V3oŠ

LYNXR Series, LYNXR-EN specifications

The Honeywell LYNXR Series, particularly the LYNXR-EN model, represents a pinnacle of advanced security technology designed for residential and small business applications. This all-in-one wireless security system is lauded for its innovative features, ease of use, and powerful performance, making it a top choice among users seeking enhanced security solutions.

One of the standout features of the LYNXR-EN is its user-friendly touchscreen interface. The large, intuitive display allows for straightforward navigation, enabling users to arm or disarm the system, check status, and receive alerts with just a few taps. This ease of use is complemented by programmable quick access keys, which allow users to personalize their experience according to their security requirements.

Additionally, the LYNXR-EN is designed with flexibility in mind. It supports a wide range of wireless sensors and devices, facilitating comprehensive coverage for homes or small businesses. Users can integrate door and window contacts, motion detectors, glass break sensors, and more, ensuring that every entry point is monitored. The system can accommodate up to 48 wireless zones, allowing for extensive security applications without the clutter of wires.

Technologically, the LYNXR-EN leverages advanced RF technology, enhancing the reliability of communication between the panel and sensors. This feature minimizes the risk of interference and ensures consistent performance even in challenging environments. Along with this robust connectivity, the system offers dual-path communication capabilities, enabling both IP and cellular reporting. This redundancy ensures that alerts are promptly sent to the monitoring center and mobile devices, providing peace of mind to users.

Moreover, the LYNXR-EN can be easily integrated with smart home technology. It is compatible with various smart devices, allowing users to control lighting, thermostats, and other home automation features from a single platform. This integration not only enhances convenience but also optimizes energy efficiency.

The LYNXR-EN also includes a built-in battery backup, ensuring that the system remains operational during power outages. This is a crucial feature for maintaining security when it is needed most. Additionally, users can set up customizable alerts and notifications, allowing them to stay informed of any unusual activity in real-time.

In summary, the Honeywell LYNXR Series, especially the LYNXR-EN model, combines advanced technology with user-friendly design to deliver a versatile and robust security solution. Its wireless capabilities, comprehensive sensor support, smart home integration, and reliable communication make it a prominent choice in the ever-evolving realm of security systems.
Top Page Image Contents