Bosch Appliances D1265 owner manual Walk Test CMD + 4 +, Using Walk Test

Page 24

D1265 Owner's Manual Part II: System Commands

If there are no events to view, There are currently no events in memory shows.

6.You can return to idle text at any time by pressing Exit button.

Walk Test (CMD + 4 + 4)

Description

Use this function to test keypads, detection devices, and sounders (both interior and exterior) to be certain they function properly. You can review untested points at your keypad to help pinpoint any problems.

You cannot arm your system while in the walk test mode, and no alarm reports are sent to your security company unless a 24-hour point is activated (such as fire or panic). A Walk Test Start Report might be programmed to be sent to your security company.

Upon initiation, the walk test tests the burglary bell pattern on the bell output and ring the keypad burglary bell for 2 sec. The AC is disabled for 4 minutes in order to test the system’s battery power. If the battery cannot maintain the system for the 4- minute period, the keypad appears to power off. If your keypads are programmed to be supervised, the main alarm panel piezo intermittently during this 4- minute period. If this happens, contact your security company. At the end of the 4-minute period, AC is returned to the system and the control panel restores. To test individual detection devices, simply activate sensors and open protected doors and windows one-at- a-time. As each detection device is faulted, the keypad emits a brief tone and the display indicates for 60 sec that the point has been tested. This verifies that each detection device is working properly.

Using Walk Test

1.Ensure the display shows disarmed idle text.

2.Press the CMD button. The display shows *System Command*.

If you prefer, you might use the function list in place of Steps 2 and 3 to initiate this function.

Press the Menu button to enter the function list.

Press the Next button repeatedly.

When you reach the Walk Test button, press it.

4.The burglary bell sounds for 2 sec. When the display shows ### points remain to be tested (### is the number of points) you can begin.

Test each point by first opening and then closing the door or window, or activating the other detection device types.

Check the display after testing each point. For interior points, walking past the device once is sufficient. If any point will not test correctly, contact your security company for service.

5.During the Walk Test you might want to refer to the points that remain untested by pressing the View untested pts button.

The display shows ### pts untested.

Press the Next Pt or Prev Pt buttons to refer to information about specific points that have not yet been tested.

3.Press the 4 button and then the 4 button.

24

Bosch Security Systems, Inc. 9/10 F01U169130-02

Page 23 Page 25
Image 24
Page 23 Page 25
Contents D1265 Page Contents Bosch Security Systems, Inc /10 F01U169130-02 Figures Introduction Your KeypadUsing the keypad Command Enter buttonsPoints Fire Points Non-Fire PointsYour Custom Display View Faulted or Bypassed Points To Scroll Faulted or Bypassed PointsKeypad Quiets for Button presses Priority of EventsFire Alarms Silencing Fire AlarmsBurglary Alarms Silencing Burglary AlarmsFire Trouble and Fire Supervisory Events Silencing Fire Trouble and Fire Supervisory conditionsSilencing an Alarm Non-Fire Trouble and Supervisory EventsSpecial System Trouble Display How Your System Reports Alarms Part II System Commands Passcode Protected Commands and Functions Turning the System On ArmingTurning the System Off Disarming To Turn Your Security System On ArmTurning On the System Arming With a Duress Passcode Turning On the System Arming With Doors or Windows OpenBosch Security Systems, Inc /10 F01U169130-02 Using Master Arm Master Arm CMD +Description Master Arming all Areas Turn On the Perimeter With No Delays Description Using Perimeter Instant Master Arm Instant CMD + 1 + Perimeter Instant CMD +Perimeter Delay CMD + Turn On the Perimeter With Delays DescriptionUsing Perimeter Delay View Alarm Memory CMD + 4 + Using CMDUsing View Alarm Memory Silence Trouble Sound/Clear Trouble Display CMD +Using Walk Test Walk Test CMD + 4 +Reset Sensors CMD + 4 + Using Reset SensorsWatch Mode CMD + Using Watch ModeEntering Watch Mode Using Perimeter Partial Perimeter Partial CMD +Partially Turn On the Perimeter Description Special Alerts CMD + 7 and CMD + Using Command Advanced Commands Terms Used in This SectionUsing Bypass a Point Bypass a Point CMD +Bosch Security Systems, Inc /10 F01U169130-02 Using Unbypass a Point Unbypass a Point CMD + 0 +Using Send Report Send Report CMD + 4+1 or 4+2Remote Program CMD + 4 + For systems without a phone numberFor systems with a phone number configured For systems with a network connectionChange Time/Date CMD + 4 + Set Date button disappears when the first digit is entered Using Door Control Door Control CMD + 4 +Cycle Door Door StatusUnlock Door Secure DoorAccess Level Change Display CMD + 4 + Extend Closing CMD + 5 +Show Continuous Time/Date Bosch Security Systems, Inc /10 F01U169130-02 Using Chg Skeds Chg Skeds CMD + 5 +Sked Table Delete User CMD + 5 + Using Change Passcode Change Relay CMD + 5 +Change Passcode CMD + 5 + Add/Change User CMD + 5 + Page Add/Change Passcode User 3 is used here as an exampleBosch Security Systems, Inc /10 F01U169130-02 Add/Change Level Adding/Changing a User’s Name Add/Change Card Add/Change Sub-User ID Default Text CMD + 5 + Using Fire TestFire Test CMD + 5 + Bosch Security Systems, Inc /10 F01U169130-02 Service Menu 9 + 9 + Enter Display Rev CMD + 5 +Using View Log Using Print LogUsing Display Revision Keypad Setup Menu Using Default TextWorking with Multiple Areas from a Single Keypad View Area StatusView Point Status Screen Area DefinitionsMove To Area CMD + 5 + Turning On the SystemTurning on Selected Areas Faulted Points in Other Areas Turning on Multiple Areas with a PasscodeTurn On the Entire System Without Delays Turning on All or Selected AreasTurning Off the System Turning Off Multiple Areas with a PasscodeTurning Off Multiple Areas with Disarm All Turning Off Selected Areas Supplementary Information for Adding Passcodes User Authority LevelsPasscode Worksheet User InterfaceAuthority Levels User Passcode Worksheet User 000 to ### User Passcode Worksheet User 039 to Bosch Security Systems, Inc /10 F01U169130-02 User Area Authority ### Passcode Group User Name Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 115 Site Card Data User Area Authority ### Passcode Group Bosch Security Systems, Inc /10 F01U169130-02 Bosch Security Systems, Inc /10 F01U169130-02 Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 User Area Authority ### Passcode Group Bosch Security Systems, Inc /10 F01U169130-02 User Passcode Worksheet Blank Security System Limitations User Token Worksheet BlankFire Safety and Evacuation ViewStandard Displays System Trouble Displays Service Printer Service D9210Service Zonex Bus 1 or Hour Point BypassSecurity System Glossary Maintenance and Service How to Clean the KeypadYour Alarm Company Bosch Security Systems, Inc /10 F01U169130-02 Bosch Security Systems, Inc Perinton Parkway Fairport, NY
Top Page Image Contents