Bosch Appliances D1265 owner manual Special Alerts CMD + 7 and CMD +, Using CMD

Page 28

D1265 Owner's Manual Part II: System Commands

5.The display prompts the user to exit the area and starts counting down # seconds to arm the system.

Special Alerts (CMD + 7 and CMD + 9)

Description

Commands 7 and 9 can be programmed to respond to specific situations that might need immediate attention. They might also be used to send a silent alarm to your security company without sounding an alarm signal on the premises. Check with your security company for the options they offer.

Using CMD 7

# is the number of sec remaining in the countdown.

6.When exit delay time expires and the system turns on, the display shows:

7.To disarm, enter your personal passcode and press ENTER.

1.Ensure your keypad shows idle text.

2.Press the CMD button. The display shows *System Command*.

3.Press the 7 button.

If you prefer, you might use the function list in place of Steps 2 and 3 to initiate this function.

Press the Menu button to enter the function list.

Press the Next button repeatedly.

When you reach the User Command 7 button, press it.

4.Your Command 7 special alert has been programmed to:

notify your alarm company

ring a bell on your premises

display at your keypad

Description:

_________________________________________

_________________________________________

28	Bosch Security Systems, Inc. 9/10 F01U169130-02

Image 28

Contents D1265 Page Contents Bosch Security Systems, Inc /10 F01U169130-02 Figures Introduction Your KeypadCommand Enter buttons Using the keypadPoints Fire Points Non-Fire PointsYour Custom Display View Faulted or Bypassed Points To Scroll Faulted or Bypassed PointsKeypad Quiets for Button presses Priority of EventsFire Alarms Silencing Fire AlarmsBurglary Alarms Silencing Burglary AlarmsFire Trouble and Fire Supervisory Events Silencing Fire Trouble and Fire Supervisory conditionsNon-Fire Trouble and Supervisory Events Silencing an AlarmSpecial System Trouble Display How Your System Reports Alarms Part II System Commands Passcode Protected Commands and Functions Turning the System On ArmingTurning the System Off Disarming To Turn Your Security System On ArmTurning On the System Arming With a Duress Passcode Turning On the System Arming With Doors or Windows OpenBosch Security Systems, Inc /10 F01U169130-02 Master Arm CMD + Using Master ArmDescription Master Arming all Areas Turn On the Perimeter With No Delays Description Using Perimeter InstantMaster Arm Instant CMD + 1 + Perimeter Instant CMD +Turn On the Perimeter With Delays Description Perimeter Delay CMD +Using Perimeter Delay View Alarm Memory CMD + 4 + Using CMDUsing View Alarm Memory Silence Trouble Sound/Clear Trouble Display CMD +Using Walk Test Walk Test CMD + 4 + Reset Sensors CMD + 4 + Using Reset SensorsUsing Watch Mode Watch Mode CMD +Entering Watch Mode Perimeter Partial CMD + Using Perimeter PartialPartially Turn On the Perimeter Description Special Alerts CMD + 7 and CMD + Using Command Advanced Commands Terms Used in This SectionUsing Bypass a Point Bypass a Point CMD +Bosch Security Systems, Inc /10 F01U169130-02 Using Unbypass a Point Unbypass a Point CMD + 0 +Using Send Report Send Report CMD + 4+1 or 4+2Remote Program CMD + 4 + For systems without a phone numberFor systems with a phone number configured For systems with a network connectionChange Time/Date CMD + 4 + Set Date button disappears when the first digit is entered Using Door Control Door Control CMD + 4 +Cycle Door Door StatusUnlock Door Secure DoorAccess Level Extend Closing CMD + 5 + Change Display CMD + 4 +Show Continuous Time/Date Bosch Security Systems, Inc /10 F01U169130-02 Using Chg Skeds Chg Skeds CMD + 5 +Sked Table Delete User CMD + 5 + Change Relay CMD + 5 + Using Change PasscodeChange Passcode CMD + 5 + Add/Change User CMD + 5 + Page Add/Change Passcode User 3 is used here as an exampleBosch Security Systems, Inc /10 F01U169130-02 Add/Change Level Adding/Changing a User’s Name Add/Change Card Add/Change Sub-User ID Using Fire Test Default Text CMD + 5 +Fire Test CMD + 5 + Bosch Security Systems, Inc /10 F01U169130-02 Service Menu 9 + 9 + Enter Display Rev CMD + 5 +Using Print Log Using View LogUsing Display Revision Keypad Setup Menu Using Default TextWorking with Multiple Areas from a Single Keypad View Area StatusView Point Status Screen Area DefinitionsTurning On the System Move To Area CMD + 5 +Turning on Selected Areas Faulted Points in Other Areas Turning on Multiple Areas with a PasscodeTurn On the Entire System Without Delays Turning on All or Selected AreasTurning Off Multiple Areas with a Passcode Turning Off the SystemTurning Off Multiple Areas with Disarm All Turning Off Selected Areas Supplementary Information for Adding Passcodes User Authority LevelsPasscode Worksheet User InterfaceAuthority Levels User Passcode Worksheet User 000 to ### User Passcode Worksheet User 039 to Bosch Security Systems, Inc /10 F01U169130-02 User Area Authority ### Passcode Group User Name Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 115 Site Card Data User Area Authority ### Passcode Group Bosch Security Systems, Inc /10 F01U169130-02 Bosch Security Systems, Inc /10 F01U169130-02 Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 User Area Authority ### Passcode Group Bosch Security Systems, Inc /10 F01U169130-02 User Passcode Worksheet Blank Security System Limitations User Token Worksheet BlankFire Safety and Evacuation ViewStandard Displays System Trouble Displays Service Printer Service D9210Service Zonex Bus 1 or Hour Point BypassSecurity System Glossary How to Clean the Keypad Maintenance and ServiceYour Alarm Company Bosch Security Systems, Inc /10 F01U169130-02 Bosch Security Systems, Inc Perinton Parkway Fairport, NY