Bosch Appliances D1265 owner manual Remote Program CMD + 4 +, For systems without a phone number

Page 35

D1265 Owner's Manual Part III: Advanced Commands

6.When the transmission is complete the keypad shows Report sent for 5 sec.

If the Exit button is pressed before 5 sec have elapsed, idle text is shown.

The display returns to idle text.

7.If the test (or status) report does not successfully transmit to the central station, the keypad might sound a trouble tone and display Comm Fail Route Grp# (# = 1-4) after numerous unsuccessful attempts.

Remote Program (CMD + 4 + 3)

Description

This function allows the user to initiate Remote Programming Software (RPS) sessions. When the phone is ringing at the control panel, the user initiates this function to have the control panel seize the line.

Your security company can remotely program your security system using the telephone line to which your control panel is connected. Typical remote programming functions include: changing personal passcodes, changing entry/exit delays, resetting the system clock/calendar, and adding/deleting system arming commands.

Your security company might ask you to follow the steps below to begin a remote programming session. The time it takes to program the control panel is dependent on the number of changes made to the program.

You’ll notice that two sets of procedures are presented. The one you use depends upon whether your system has a pre-programmed telephone number in its memory.

My system does not have the RPS phone or the RPS network configured.

For systems without a phone number

1.Ensure the display shows disarmed idle text.

2.Call this phone number:

This number is designated for the RPS.

You must make the call using the telephone located at:

___________________________

3.Identify yourself and your premises (account number, name, address, etc.) and advise the operator of the services you wish to have performed. When the operator instructs you, proceed to Steps 4 through 6.

4.Press the CMD button. The display shows *System Command*.

5.Press the 4 button then the 3 button.

6.Advance the menu (if necessary) and select the Allow Answer option.

Bosch Security Systems, Inc. 9/10 F01U169130-02

35

Image 35

Contents D1265 Page Contents Bosch Security Systems, Inc /10 F01U169130-02 Figures Your Keypad IntroductionPoints Using the keypadCommand Enter buttons Non-Fire Points Fire PointsYour Custom Display Priority of Events View Faulted or Bypassed PointsTo Scroll Faulted or Bypassed Points Keypad Quiets for Button pressesSilencing Fire Alarms Fire AlarmsSilencing Fire Trouble and Fire Supervisory conditions Burglary AlarmsSilencing Burglary Alarms Fire Trouble and Fire Supervisory EventsSpecial System Trouble Display Silencing an AlarmNon-Fire Trouble and Supervisory Events How Your System Reports Alarms Part II System Commands To Turn Your Security System On Arm Passcode Protected Commands and FunctionsTurning the System On Arming Turning the System Off DisarmingTurning On the System Arming With Doors or Windows Open Turning On the System Arming With a Duress PasscodeBosch Security Systems, Inc /10 F01U169130-02 Description Using Master ArmMaster Arm CMD + Master Arming all Areas Perimeter Instant CMD + Turn On the Perimeter With No Delays DescriptionUsing Perimeter Instant Master Arm Instant CMD + 1 +Using Perimeter Delay Perimeter Delay CMD +Turn On the Perimeter With Delays Description Silence Trouble Sound/Clear Trouble Display CMD + View Alarm Memory CMD + 4 +Using CMD Using View Alarm MemoryWalk Test CMD + 4 + Using Walk TestUsing Reset Sensors Reset Sensors CMD + 4 +Entering Watch Mode Watch Mode CMD +Using Watch Mode Partially Turn On the Perimeter Description Using Perimeter PartialPerimeter Partial CMD + Special Alerts CMD + 7 and CMD + Using Command Terms Used in This Section Advanced CommandsBypass a Point CMD + Using Bypass a Point Bosch Security Systems, Inc /10 F01U169130-02 Unbypass a Point CMD + 0 + Using Unbypass a PointSend Report CMD + 4+1 or 4+2 Using Send ReportFor systems without a phone number Remote Program CMD + 4 +For systems with a network connection For systems with a phone number configuredChange Time/Date CMD + 4 + Set Date button disappears when the first digit is entered Door Status Using Door ControlDoor Control CMD + 4 + Cycle DoorSecure Door Unlock DoorAccess Level Show Continuous Time/Date Change Display CMD + 4 +Extend Closing CMD + 5 + Bosch Security Systems, Inc /10 F01U169130-02 Chg Skeds CMD + 5 + Using Chg SkedsSked Table Delete User CMD + 5 + Change Passcode CMD + 5 + Using Change PasscodeChange Relay CMD + 5 + Add/Change User CMD + 5 + Page User 3 is used here as an example Add/Change PasscodeBosch Security Systems, Inc /10 F01U169130-02 Add/Change Level Adding/Changing a User’s Name Add/Change Card Add/Change Sub-User ID Fire Test CMD + 5 + Default Text CMD + 5 +Using Fire Test Bosch Security Systems, Inc /10 F01U169130-02 Display Rev CMD + 5 + Service Menu 9 + 9 + EnterUsing Display Revision Using View LogUsing Print Log Using Default Text Keypad Setup MenuView Area Status Working with Multiple Areas from a Single KeypadScreen Area Definitions View Point StatusTurning on Selected Areas Move To Area CMD + 5 +Turning On the System Turning on Multiple Areas with a Passcode Faulted Points in Other AreasTurning on All or Selected Areas Turn On the Entire System Without DelaysTurning Off Multiple Areas with Disarm All Turning Off the SystemTurning Off Multiple Areas with a Passcode Turning Off Selected Areas User Interface Supplementary Information for Adding PasscodesUser Authority Levels Passcode WorksheetAuthority Levels User Passcode Worksheet User 000 to ### User Passcode Worksheet User 039 to Bosch Security Systems, Inc /10 F01U169130-02 User Area Authority ### Passcode Group User Name Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 115 Site Card Data User Area Authority ### Passcode Group Bosch Security Systems, Inc /10 F01U169130-02 Bosch Security Systems, Inc /10 F01U169130-02 Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 User Area Authority ### Passcode Group Bosch Security Systems, Inc /10 F01U169130-02 User Passcode Worksheet Blank User Token Worksheet Blank Security System LimitationsView Fire Safety and EvacuationStandard Displays System Trouble Displays Hour Point Bypass Service PrinterService D9210 Service Zonex Bus 1 orSecurity System Glossary Your Alarm Company Maintenance and ServiceHow to Clean the Keypad Bosch Security Systems, Inc /10 F01U169130-02 Bosch Security Systems, Inc Perinton Parkway Fairport, NY