Heat & Glo LifeStyle LUX60 owner manual Mailbox Style Shroud may be used with DVP-TV, DVP-TVHW

Page 42

Mailbox Style Shroud (may be used with DVP-TV, DVP-TVHW)

Min. Height

Min. Base Dim

Min.

Base Dim

Figure 11.2 Mailbox Style Shroud Dimensions

Min. Base Dims.

in

20 x 20

mm508 x 508

Min. Height

in

18

mm457

Roofed Style Shroud (may be used with DVP-TV, DVP-TVHW)

Minimum

Height

 

Minimum

 

Opening

Min. Opening

Height

Width

 

Minimum

Base Dimension

Figure 11.3 Roofed Style Shroud Dimensions

Min. Base Dims.

in

20 x 20

mm508 x 508

Min. Height

in

18

mm458

Min. Opening Width

in

14

mm356

Min. Opening Height

in

10

mm254

42

Heat & Glo • LUX60 • 4062-116 • Rev. G • 4/11

Image 42
Contents Installation and Operation ModelsCongratulations Homeowner Reference InformationTable of Contents Reference Materials  B. Limited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyClear Space Operation of the LUX60Before Lighting Fireplace Matching Security CodesSystem Operation For Your Safety Read Before Lighting IntelliFire Ignition System IPI Lighting InstructionsFrequently Asked Questions Initial Break-in ProcedureAfter Fireplace is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Doors, Surrounds, FrontsVenting Firebox Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Control Compartment and Firebox TopLight Glass Replacement/Cleaning LED Light Bar ReplacementClean Porcelain Panels BackRemove Screws Getting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Select Appliance LocationAssemble Steel Stud Kit Construct the Appliance Chase ClearancesClearances to Combustibles Termination Locations Vent Termination Minimum ClearancesMinimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of ElbowsVent Diagrams Top Vent Horizontal TerminationOne Elbow Two 45 Elbows replacing One 90 Elbow Three ElbowsTop Vent Vertical Termination No ElbowTwo Elbows Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall PenetrationInstall the Ceiling Firestop Ceiling firestop Must be used between floors and at- ticsInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Secure and Level the ApplianceAssemble Vent Sections Install Vent PipeAttach Pipe to the Firebox Assembly Assemble Pipe SectionsAssemble Slip Sections Secure the Vent SectionsInstall Metal Roof Flashing Disassemble Vent SectionsAssemble and Install Storm Collar 13 Assembling the Storm CollarInstall Vertical Termination Cap Heat Shield Requirements for Horizontal TerminationInstall Horizontal Termination Cap 16 Venting through the wallField Constructed Shrouds ShroudsHHT Shrouds Open Top Shroud may be used with DVP-TV, DVP-TVHWMailbox Style Shroud may be used with DVP-TV, DVP-TVHW Roofed Style Shroud may be used with DVP-TV, DVP-TVHWGas Information Gas PressureGas Connection Install Flame Solenoid Setting Flame Height/Manifold PressureWiring Requirements Electrical Service and RepairElectrical Information Junction Box Installation Junction Box DetailWall Finishing Standard 1/2 in mm SheetrockAdditional Decorative Finishing up to 1 in mm Thick Additional Decorative Finishing over 1 in mm ThickAir Shutter Access & Adjustment Appliance SetupRemove Glass Assembly Clean the ApplianceOutside Burner Tube Air Shutter Adjustment Center Burner Tube Air ShutterInstall Glass Rock Install Glass RockTroubleshooting IntelliFire IPI Ignition SystemIntelliFire IPI Ignition System Appliance Dimension Diagram Reference MaterialsVent Components Diagrams DVP45DVP-TRAPFL DVP-TVHW DVP-TRAP Optional Components Contact Information Do not Discard this Manual