Regency P42-LP3, P42-NG3 Rigid Pipe Venting Arrangements Horizontal Terminations

Page 13

INSTALLATION

RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS

REGENCY DIRECT VENT SYSTEM (FLEX) (Propane & Natural Gas)

The shaded areas in the diagram show all allowable combinations of vertical runs with horizontal terminations. The chart below shows the distances with one 90o bend (two 45o elbows equal one 90o elbow). For a second 90o bend, see page 14.

		A vent guard may be required, check local codes.
	Minimum height	Note: Must use optional rigid pipe adaptor (Part # 510-
	Minimum height	994) when using rigid pipe venting systems.
	requirement	994) when using rigid pipe venting systems.
	requirement
		Rigid Pipe Systems:
		4"(100mm) inner diameter
		6-5/8"(168mm) outer diameter
		Regency Flex:
		4"(100mm) inner diameter
		6-7/8"(175mm) outer diameter

•Rigid Pipe Systems: Maintain a 1-1/4"(32mm) clearance to combustibles

•Regency Flex: Maintain a 1-1/2"(38mm) clearance to combustibles

•Horizontal vent must be supported every 3 feet (0.9 meter)

•Firestops are required at each floor level and whenever passing through a wall

Note: Regency Direct Vent System (Flex) is only approved for horizontal terminations.

Regency P42-3 Zero Clearance Direct Vent Gas Fireplace

13

Image 13

Contents P42 Gas Fireplace To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Copy of Safety Decal for P42 Safety LabelGeneral Safety Information InstallationInstallation Checklist Save These InstructionsManufactured Mobile Home Additional Requirements Unit Specifications Locating Your GAS StoveOptional Duct System Optional Heat ReleaseMantel LEG Clearances Clearances MantelsFraming Finishing TOP Assembly Nailing StripsVenting Introduction Vent RestrictorExterior Vent Termination Regency Direct Vent System Flex Horizontal Terminations Only Venting4DT-AJB Rigid Pipe Venting Components ListAlternate Rigid Pipe VentingHorizontal TerminationVent guard may be required, check local codes Rigid Pipe Venting Arrangements Horizontal TerminationsFor All Horizontal Terminations Propane & Natural Gas Rigid Pipe Venting Arrangements Vertical TerminationsVent restrictor #6 must be used Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Alternate Approved CapsInstallation Below Grade Installation Horizontal InstallationsSnorkel Terminations Continue to assemble pipe lengths Vertical TerminationOffset Chart Installation ProceduresFor Regency Direct Vent System Flex GAS Pipe Pressure Testing GAS Line InstallationHigh Elevation Aeration Brick Panels Adjustment Natural GAS LOG SET InstallationPropane Burner tray without front logs in placeFlush Louvers Standard Flush DoorDouble Screen Door Not under the gas lineBAY Louvers Optional BAY DoorOptional Bay Trim Full Screen Front Full Screen Door Frame InstallationHinge Location Bottom Grill Hinge Screen Door To Thermocouple T Valve Wiring DiagramDo not cut the ground terminal off under any circumstances Optional Wall Switch Remote ControlLighting Procedure Operating InstructionsClean. See installation Temperatures keep children, clothingCopy of the Lighting Plate Instructions Maintenance MaintenanceShutdown Procedure First FireLOG Replacement Glass ReplacementGOLD-PLATED Louvers Thermopile ThermocoupleRemoving the FAN Replacing the FAN Shut the power offInstalling Valve P42 Main Assembly Parts ListP42 Burner & LOG Assembly P42 Flush Door & Louvers P42 BAY Front & Louvers Regency P42-3 Zero Clearance Direct Vent Gas Fireplace Regency P42-3 Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyInstaller Please complete the following information