Regency L676-1, L676-NG1, L676-LP1 Installation, F Ba C, 1st Grate Post, 4th Grate Post

Page 34
1st Grate Post

INSTALLATION

INSTALLATION

8)Fit the notch at the center of the underside of log B onto the 2nd grate post while resting the small notch on the left end of log B on the 1st grate post.

BC

10) Fit log F into the pin on the far right side of log A. Rest the 2 ends of log F on the landings on log C.

1st Grate Post

2nd Grate Post

F

BA

C

9)Rest the notch on the underside log C onto the 4th grate post.

F

C

4th Grate Post

34

Regency® L676-1 Direct Vent Gas Fireplace

Image 34
Contents LIBERTY L676-1Gas Fireplace Congratulations MANUFACTURED MOBILE HOME REQUIREMENTSINSTALLATION TABLE OF CONTENTSSAFETY LABEL WARRANTYSAFETY LABEL INSTALLATIONMA Code - CO Detector REQUIREMENTSINSTALLATION 5.08: Modifications to NFPA-54,ChapterINSTALLATION UNIT DIMENSIONSRegency L676-1Direct Vent Gas Fireplace INSTALLATION CHECKLIST INSTALLATIONGENERAL SAFETY INFORMATION INSTALLATIONDiagram INSTALLATIONINSTALLATION HEAT RELEASE KITClearance to Combustibles from INSTALLATIONCLEARANCES Minimum Clearance from Top of Front FacingMANTEL CLEARANCES INSTALLATIONINSTALLATION MANTEL LEG CLEARANCESDiagram Diagram INSTALLATIONINSTALLATION DiagramINSTALLATION INSTALLATIONUNIT ASSEMBLY PRIOR TO INSTALLATION FINISHING TEMPLATEVENT RESTRICTOR POSITION INSTALLATIONINSTALLATION Vent Restrictor PlateEXTERIOR VENT TERMINATION REQUIREMENTS INSTALLATIONINSTALLATION Minimum Clearance RequirementsVENTING ARRANGEMENTS INSTALLATIONINSTALLATION FPI Kit #When using Rigid Vent other than INSTALLATIONINSTALLATION RIGID PIPE VENTING SYSTEMS5” X 8” RIGID PIPE CROSS REFERENCE CHART INSTALLATIONINSTALLATION INSTALLATION INSTALLATIONRegency L676-1Direct Vent Gas Fireplace VENT RESTRICTOR SETTING INSTALLATIONINSTALLATION VENTING ARRANGEMENTSHorizontal Venting with Two 2 90o Elbows INSTALLATIONINSTALLATION Horizontal Venting with Three 3 90o ElbowsVENT RESTRICTOR SETTING INSTALLATIONINSTALLATION Vertical Venting with Three 3 90o ElbowsVENTING ARRANGEMENTS INSTALLATIONINSTALLATION ALLOWABLE VERTICAL TERMINATIONSINSTALLATION INSTALLATIONUNIT INSTALLATION WITH HORIZONTAL TERMINATION DiagramINSTALLATION INSTALLATIONUNIT INSTALLATION WITH VERTICAL TERMINATION DiagramINSTALLATION INSTALLATIONUNIT INSTALLATION ASTROCAP XL DIMENSIONS 946-623/PGAS LINE INSTALLATION INSTALLATIONPILOT ADJUSTMENT TESTINGWIRING DIAGRAM INSTALLATIONAERATION ADJUSTMENT INSTALLATIONCONVERSION KIT #522-969FROM NG TO LP INSTALLATIONINSTALLATION LP Conversion Kit ContainsNOTE Once the unit has been installed INSTALLATIONINSTALLATION Burner TubeINSTALLATION INSTALLATIONBRICK PANEL INSTALLATION Diagram Right Side Rod with Screen RemovedBurner Orifi ce Cover Plate Diagram INSTALLATIONINSTALLATION DiagramINSTALLATION INSTALLATIONLOG SET INSTALLATION Log kit # 522-930contains the following pieces5 Fit log A into the pins on the log tray INSTALLATIONINSTALLATION 7 Fit log E into the pin at the center of log AF BA C INSTALLATIONINSTALLATION 1st Grate PostCompleted Log Set Installation INSTALLATIONINSTALLATION E F A B CINSTALLATION INSTALLATIONMESH PULL SCREEN INSTALLATION Left Side Rod Right Side RodFinal Installation L900-1 OPTIONAL ANDIRON INSTALLATIONINSTALLATION Log GLIGHTING PROCEDURE OPERATING INSTRUCTIONSMATCHING REMOTE CONTROL & RECEIVER CODE SHUTDOWN PROCEDURECOPY OF LIGHTING PLATE INSTRUCTIONS OPERATING INSTRUCTIONSNORMAL OPERATING SOUNDS OF GAS APPLIANCES DO NOT REMOVE THIS INSTRUCTION PLATELOG REPLACEMENT MAINTENANCEMAINTENANCE INSTRUCTIONS GENERAL VENT MAINTENANCEDC SPARK BOX REPLACEMENT MAINTENANCEDC SPARK BOX BATTERY REPLACEMENT MAINTENANCEMAINTENANCE MAINTENANCEVALVE TRAY REPLACEMENT Latch Location LatchDC Spark Box MAINTENANCEMAINTENANCE DC Spark BoxPARTS LIST PARTS LISTMAIN ASSEMBLY Part #PARTS LIST PARTS LISTPARTS LIST PARTS LISTBURNER & LOG ASSEMBLY Part #Conditions WARRANTYThe Warranty: Limited Lifetime ExclusionsSee the inside back cover for details