Regency L676-1, L676-NG1, L676-LP1 installation manual Maintenance, DC Spark Box, Valve Tray

Page 43
Valve Tray

MAINTENANCE

11)Disconnect the inlet gas line from the valve.

12)Undo the center wire clip on the side of the firebox.

15) Disconnect the 2 DC Spark generator wires

17) Remove the 16 screws that hold the valve

from the DC spark box located in front of

tray to the firebox and slightly pull out the

the valve.

valve tray.

13)Unplug the wire harness that connects the modulating coil to the receiver.

14)Unplug the green (TH) and white (TP/TH) wires from the valve.

DC Spark Box

16)Disconnect the spark electrode wire from the DC spark box.

DC Spark Box

Valve Tray

18)Completely pull out the valve tray.

19)Replace the valve tray and reverse steps to re-install.

20)Turn on the gas supply and check for gas leaks.

21)Re-install the rear log stand.

22)Re-install the burner tube.

23)Re-install the grate.

24)Re-install the brick panels.

25)Re-install the burner ofirice cover plate.

26)Re-install the log set.

27)Re-install the glass door.

28)Re-install the front cover plate

29)Re-install the mesh screen.

30)Check the inlet and outlet pressures.

31)Check operation of flame control.

32)Check for proper flame appearance.

MAINTENANCE

Regency® L676-1 Direct Vent Gas Fireplace

43

Image 43
Contents LIBERTY L676-1Gas Fireplace MANUFACTURED MOBILE HOME REQUIREMENTS CongratulationsWARRANTY TABLE OF CONTENTSSAFETY LABEL INSTALLATIONINSTALLATION SAFETY LABEL5.08: Modifications to NFPA-54,Chapter REQUIREMENTSINSTALLATION MA Code - CO DetectorINSTALLATION UNIT DIMENSIONSRegency L676-1Direct Vent Gas Fireplace INSTALLATION INSTALLATIONGENERAL SAFETY INFORMATION INSTALLATION CHECKLISTHEAT RELEASE KIT INSTALLATIONINSTALLATION DiagramMinimum Clearance from Top of Front Facing INSTALLATIONCLEARANCES Clearance to Combustibles fromMANTEL LEG CLEARANCES INSTALLATIONINSTALLATION MANTEL CLEARANCESDiagram INSTALLATIONINSTALLATION Diagram DiagramFINISHING TEMPLATE INSTALLATIONUNIT ASSEMBLY PRIOR TO INSTALLATION INSTALLATIONVent Restrictor Plate INSTALLATIONINSTALLATION VENT RESTRICTOR POSITIONMinimum Clearance Requirements INSTALLATIONINSTALLATION EXTERIOR VENT TERMINATION REQUIREMENTSFPI Kit # INSTALLATIONINSTALLATION VENTING ARRANGEMENTSRIGID PIPE VENTING SYSTEMS INSTALLATIONINSTALLATION When using Rigid Vent other than5” X 8” RIGID PIPE CROSS REFERENCE CHART INSTALLATIONINSTALLATION INSTALLATION INSTALLATIONRegency L676-1Direct Vent Gas Fireplace VENTING ARRANGEMENTS INSTALLATIONINSTALLATION VENT RESTRICTOR SETTINGHorizontal Venting with Three 3 90o Elbows INSTALLATIONINSTALLATION Horizontal Venting with Two 2 90o ElbowsVertical Venting with Three 3 90o Elbows INSTALLATIONINSTALLATION VENT RESTRICTOR SETTINGALLOWABLE VERTICAL TERMINATIONS INSTALLATIONINSTALLATION VENTING ARRANGEMENTSDiagram INSTALLATIONUNIT INSTALLATION WITH HORIZONTAL TERMINATION INSTALLATIONDiagram INSTALLATIONUNIT INSTALLATION WITH VERTICAL TERMINATION INSTALLATIONASTROCAP XL DIMENSIONS 946-623/P INSTALLATIONUNIT INSTALLATION INSTALLATIONTESTING INSTALLATIONPILOT ADJUSTMENT GAS LINE INSTALLATIONINSTALLATION INSTALLATIONAERATION ADJUSTMENT WIRING DIAGRAMLP Conversion Kit Contains INSTALLATIONINSTALLATION CONVERSION KIT #522-969FROM NG TO LPBurner Tube INSTALLATIONINSTALLATION NOTE Once the unit has been installedDiagram Right Side Rod with Screen Removed INSTALLATIONBRICK PANEL INSTALLATION INSTALLATIONDiagram INSTALLATIONINSTALLATION Burner Orifi ce Cover Plate DiagramLog kit # 522-930contains the following pieces INSTALLATIONLOG SET INSTALLATION INSTALLATION7 Fit log E into the pin at the center of log A INSTALLATIONINSTALLATION 5 Fit log A into the pins on the log tray1st Grate Post INSTALLATIONINSTALLATION F BA CE F A B C INSTALLATIONINSTALLATION Completed Log Set InstallationLeft Side Rod Right Side Rod INSTALLATIONMESH PULL SCREEN INSTALLATION INSTALLATIONLog G OPTIONAL ANDIRON INSTALLATIONINSTALLATION Final Installation L900-1SHUTDOWN PROCEDURE OPERATING INSTRUCTIONSMATCHING REMOTE CONTROL & RECEIVER CODE LIGHTING PROCEDUREDO NOT REMOVE THIS INSTRUCTION PLATE OPERATING INSTRUCTIONSNORMAL OPERATING SOUNDS OF GAS APPLIANCES COPY OF LIGHTING PLATE INSTRUCTIONSGENERAL VENT MAINTENANCE MAINTENANCEMAINTENANCE INSTRUCTIONS LOG REPLACEMENTMAINTENANCE MAINTENANCEDC SPARK BOX BATTERY REPLACEMENT DC SPARK BOX REPLACEMENTLatch Location Latch MAINTENANCEVALVE TRAY REPLACEMENT MAINTENANCEDC Spark Box MAINTENANCEMAINTENANCE DC Spark BoxPart # PARTS LISTMAIN ASSEMBLY PARTS LISTPARTS LIST PARTS LISTPart # PARTS LISTBURNER & LOG ASSEMBLY PARTS LISTExclusions WARRANTYThe Warranty: Limited Lifetime ConditionsSee the inside back cover for details