INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The
BEFORE YOU START
Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:
INSTALLATION AND REPAIR SHOULD BE DONE BY AN AUTHORIZED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPE- CIALLY THE FIREPLACE GLASS, AND SHOULD STAYAWAYTOAVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.
CLOTHING OR OTHER FLAMMABLE MATERIALSHOULDNOTBEPLACED ON OR NEAR THE APPLIANCE.
GENERAL SAFETY
INFORMATION
1)The appliance installation must conform with local codes or, in the absence of local codes, with the current Canadian or National Gas Codes,
2)The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.
3)See general construction and assembly instructions. The appliance and vent should be enclosed.
4)This appliance must be connected to the specified vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is fitted as per Venting instructions.
5)Inspect the venting system annually for blockage and any signs of deterioration.
6)Venting terminals shall not be recessed into a wall or siding.
7)Any safety glass removed for servicing must be replaced prior to operating the appliance.
8)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fireplace.
9)Wearglovesandsafety glassesforprotection while doing required maintenance.
10)Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination.
11)Under no circumstances should this appliance be modified. Parts that have to be removed for servicing should be replaced prior to operating this appliance.
12)Installation and any repairs to this appliance should be done by an authorized service person.Aprofessional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.
13)Do not slam shut or strike the glass door.
14)Under no circumstances should any solid fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.
15)The appliance area must be kept clear and free of combustible materials, (gases and other flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
INSTALLATION
CHECKLIST
1)Locate appliance
a)Room location (Refer to "Locating Your Gas fireplace" section)
b)Clearances to Combustibles (Refer to "Clearances" section)
c)Mantle Clearances (Refer to "Mantel Clearances" section)
d)Framing & Finishing Requirements (Refer to "Framing & Finishing" section)
e)Venting Requirements (Refer to "Venting" section)
2)Assemble Top and Side Standoffs (Refer to "Unit Assembly Prior to Installation).
3)Install batteries; four "AA" batteries in the wall mounted receiver; three "AAA" batteries in the remote control and one "AA" battery into the DC Sparker. (Refer to remote control manual for operating instructions).
4)Convert to propane if desired (Refer to "Conversion from NG to LP" section).
5)Slide unit into place.
6)Install vent (Refer to "Venting Arrangement" sections).
7)Make gas connections (Refer to "Gas Line Installation section).
8)Test the pilot (Refer to "Pilot Adjustment" section).
INSTALLATION
Regency® | 7 |