Wayne-Dalton 9800 Vertical Track, Tools Needed Important The tops, Door jamb

Page 14

	5	Vertical Track	fLAGANGLE
		Vertical Track	5/16” x 2”
			5/16” x 2”
			LAG SCREWS
	Tools Needed:	IMPORTANT: The tops of the
	3/16” Drill Bit	vertical tracks must be level
	3/16” Drill Bit	from side to side. If the bottom
		from side to side. If the bottom
	Power Drill	section was shimmed to level it.
	Power Drill	The vertical track on the shimmed
		The vertical track on the shimmed
	7/16” Socket	side, must be raised the height of
	7/16” Socket	the shim.
	Driver	the shim.
	Driver
	Tape Measure	Position the left hand vertical track
	Level	assembly over the rollers of the bottom	VERTICAL
		section. Make sure the counterbalance	VERTICAL
		section. Make sure the counterbalance	TRACK
	(2) Vice Grips	cable is located between the rollers and	ASSEMBLY
	(2) Vice Grips	the door jamb.	JAMB
		the door jamb.

		Drill 3/16” pilot holes for the lag screws.	BRACKET
		Drill 3/16” pilot holes for the lag screws.
		Loosely fasten jamb brackets and
		flagangle to the jamb using 5/16” x 2”
		lag screws.

Tighten lag screw securing bottom jamb bracket to jamb, to maintain 5/8” spacing.

Repeat for the right hand side.

BOTTOM

SECTION

vertical track

BOTTOM SECTION

5/8”

roller

jamb bracket

LAG

SCREW locations

lag

screw

14Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts

You May Need. You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 14

Contents Series Portland Source PlantTable of Contents Package Contents Door Section Identification Saw horses pair Power DrillTools Required Failure to use approved Spring when the set screws areTorsion Spring Removal For Standard Lift Experienced door technician. Instead haveTorqueMaster Spring Removal Unwind SpringsBracket and Drive Gear Extension Spring Removal Removing the Old DoorAttach a suitable Preparing the OpeningFailure to securely Mounting pad to structurally sound Hand tighten the flagangle to Installation Attaching Fully Adjustable Flagangle to Vertical Track None Carriage bolts and 2 1/4- 20 flangeInstalling Fully Adjustable Jamb Brackets Counterbalance Cables Bottom SectionSide, must be raised the height Shim Vertical TrackTools Needed Important The tops Position the left hand vertical trackStacking Sections Top Brackets To this DOOR, a WAYNE-DALTON ANY U-BARS Provided with DOOR. the InstallationOperator Bracket ProperlyTop Section Door OperationFlagangle Attaching Horizontal Track to AdjustableAdjusting Top Brackets Do not Raise Door Until HorizontalCenter Bearing Bracket Torsion Spring Assembly SideNylon Center Bushing Important do not USE Impact GUN To Wind Springs Securing DoorFor Spring Winding Winding Torsion Springs Parallel and within 3/4 Maximum of door edge Rear SupportKeep horizontal track Otherwise door could fall Resulting in severe injury orWinding bar while carefully loosening To adjust spring tension, fully closeThird roller. Insert a winding bar into Set screws in the winding coneSide Lock Pull RopePerforated OPERATORangle rail Trolley OperatorHeader Door ARM to Operator Bracket Operator Framing Members Perforated AngleCleaning PaintingPainting Lifetime Limited Warranty Model /or Ship Any Parts You May Need Thank you for your purchase

Related manuals

Manual 20 pages 42.88 Kb

Manual 4 pages 60.02 Kb

Manual 26 pages 11.64 Kb

Manual 38 pages 17.26 Kb

Manual 18 pages 4.37 Kb