| TorqueMaster® Spring |
|
|
|
| Removal continued... |
|
|
|
Tools Needed: | If the counterbalance cable is still taut and |
|
|
|
| the TorqueMaster® Spring Tube is difficult |
|
|
|
Recommended | to rotate, that is an indication that spring |
|
|
|
tension still exists on the left hand spring. |
|
|
| |
tools from |
|
|
| |
Repeat Steps 1 and 2 for releasing spring |
|
|
| |
page 5 | tension on the left hand side. |
|
|
|
| Step 4: Using a flat tip screwdriver, pry | remove top |
|
|
| the counter gear and counter cover |
|
| |
| from the right hand end bracket (Fig. 4 | lag screw |
|
|
| on previous page). Discard the counter |
| Fig. 5 | |
| gear and counter cover. On double spring |
|
|
|
| applications, repeat for left hand side. |
|
|
|
| Step 5: Remove the upper 5/16” x |
|
| use locking pliers |
|
|
| to hold end bracket | |
| bracket (Fig. 5). Attach locking pliers to |
|
|
|
| the upper portion of the end bracket and |
|
|
|
| hold the housing steady while removing |
|
| remove #10 |
| the lower 5/16” x |
|
| phillips head |
| #10 x 1/2” phillips head screw from the |
|
| screw |
| end bracket (Fig. 6). |
|
|
|
| Step 6: Holding the right hand end |
|
|
|
| bracket steady with locking pliers, |
|
|
|
| carefully pry the end bracket and drive |
|
|
|
| gear off the winding shaft using a flat tip | remove |
|
|
| screwdriver (Fig. 7). | bottom lag |
|
|
| CAUTION: THE WINDING SHAFT MAY | screw | Fig. 6 | |
|
| |||
| ROTATE WHEN REMOVING THE END |
|
|
|
| BRACKET AND DRIVE GEAR. |
|
| hold the |
| Step 7: Repeat Step 4 for the left hand |
|
| end bracket |
|
|
| steady with | |
| side. Holding the left hand end bracket |
|
| |
|
|
| locking pliers | |
| steady with locking pliers, carefully pry |
|
| |
|
|
|
| |
| the end bracket off the winding shaft |
|
|
|
| using a flat tip screwdriver (Fig. 7). |
|
|
|
| Step 8: Remove the two (2) lag bolts |
|
|
|
| attaching the center bracket assembly to |
|
|
|
| the header board (Fig. 8). |
|
| pry end bracket from winding |
|
|
|
| |
| Step 9: Lift the right hand side of the |
|
| shaft using a flat tip screw |
| TorqueMaster® Spring Tube and slide the |
|
| driver and locking pliers |
| cable drum off. Realign the groove in the |
|
|
|
| winding shaft with the round notch in the |
|
|
|
| flagangle and drape the counterbalance |
|
|
|
| cable with drum over the flagangle. Lift |
| Fig. 7 | |
| the left hand side of the TorqueMaster® |
| CENTER |
|
| Spring Tube and slide the cable drum |
| remove cable drum and | |
|
| BRACKET | ||
| and winding shaft off (Fig. 9). Drape the |
| ASSEMBLY | winding shaft |
| counterbalance cable with drum over the |
|
|
|
| flagangle. Lift the TorqueMaster® spring |
|
|
|
| assembly off the flagangles and out of |
|
|
|
| the doorway. Unhook the counterbalance |
|
|
|
| cables from the bottom brackets and |
|
|
|
| remove all parts from the work area. |
|
|
|
| NOTE: The cable drums may be difficult to |
|
|
|
| remove. If so, twist the cable drum to aid |
|
| lift |
| in removal. |
|
| TorqueMaster® |
| NOTE: Continue with “P4” on page 9 after |
|
| Spring Tube |
|
|
| off flagangle | |
| completing this step. |
| (2) 5/16” x | |
|
| drape cable across | ||
|
|
| hex head lag | top of flagangle |
|
|
| screws |
|
|
|
| Fig. 8 | Fig. 9 |
8Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts
You May Need. You can reach us Toll Free at