Wayne-Dalton 9800 Attaching Horizontal Track to Adjustable, Flagangle, Adjusting Top Brackets

Page 19

10

Attaching Horizontal Track to Adjustable

Flagangle

 

Tools Needed:

To install horizontal track, place the curved end over

9/16” Socket

the top roller. Align the bottom of the horizontal track

with the vertical track. Hand tighten the horizontal

 

7/16” Socket

track to the flagangle with (2) 1/4”- 20 x 5/8” carriage

bolts and (2) 1/4”- 20 flange hex nuts.

 

Ratchet Wrench

Level the horizontal track assembly and bolt the

 

9/16” Wrench

horizontal angle to the slot in the flagangle using

 

(1) 3/8”- 16 x 3/4” hex head bolt and (1) 3/8”- 16 hex

Level

nut. Repeat for other side. Remove the nail that was

Hammer

temporarily holding the top section in place, installed

in Step 9.

 

IMPORTANT: Failure to remove nail before

 

attempting to raise door could cause

 

permanent damage to top section.

 

WARNING

FLAGANGLE

horizontal

track

 

(2) 1/4”- 20 x 5/8” carriage bolts

vertical track

(2) 1/4”- 20 flange

hex nuts

(1) 3/8”- 16

hORIZONTAL ANGLE

 

Hex nut

 

HORIZONTAL

DO NOT RAISE DOOR UNTIL HORIZONTAL

TRACKS ARE SECURED­ AT REAR, AS

OUTLINED IN STEP 19, OR DOOR COULD FALL

FROM OVERHEAD POSITION­ CAUSING SEVERE

OR FATAL INJURY.

(1) 3/8”- 16 X 3/4” hex HEAD BOLT

TRACK

INSTALLATION

11

Adjusting Top Brackets

 

HORIZONTAL

 

 

 

 

track

Tools Needed:

With horizontal tracks installed, you can

top

 

section

 

 

now adjust the top brackets. Vertically

 

7/16” Wrench

 

 

align the top section of the door with the

 

 

 

 

 

 

lower sections. Once aligned, position

 

 

 

the roller in the top bracket slide, out

 

 

 

against the horizontal track.

 

 

 

Maintaining the slide’s position, tighten

 

TOP

 

the (2) 1/4”- 20 flange hex nuts to

 

 

 

ROLLER

 

secure the top bracket slide to the top

Correct

 

 

 

bracket base. Repeat for other side.

 

 

 

 

 

TOP

 

 

 

BRACKET

 

 

 

SLIDE

 

 

top

(2) 1/4”- 20

 

 

section

 

 

 

FLANGED HEX

 

 

 

NUTS

 

 

 

top

 

 

 

section

inCorrect

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts 19

You May Need. You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 19
Contents Portland Source Plant SeriesTable of Contents Package Contents Door Section Identification Tools Required Power DrillSaw horses pair Experienced door technician. Instead have Spring when the set screws areTorsion Spring Removal For Standard Lift Failure to use approvedUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Removing the Old Door Extension Spring RemovalMounting pad to structurally sound Preparing the OpeningFailure to securely Attach a suitableNone Carriage bolts and 2 1/4- 20 flange InstallationAttaching Fully Adjustable Flagangle to Vertical Track Hand tighten the flagangle toInstalling Fully Adjustable Jamb Brackets Bottom Section Counterbalance CablesPosition the left hand vertical track Vertical TrackTools Needed Important The tops Side, must be raised the height ShimStacking Sections Top Brackets Properly ANY U-BARS Provided with DOOR. the InstallationOperator Bracket To this DOOR, a WAYNE-DALTONDoor Operation Top SectionDo not Raise Door Until Horizontal Attaching Horizontal Track to AdjustableAdjusting Top Brackets FlagangleCenter Bearing Bracket Side Torsion Spring AssemblyNylon Center Bushing For Spring Winding Securing DoorImportant do not USE Impact GUN To Wind Springs Winding Torsion Springs Otherwise door could fall Resulting in severe injury or Rear SupportKeep horizontal track Parallel and within 3/4 Maximum of door edgeSet screws in the winding cone To adjust spring tension, fully closeThird roller. Insert a winding bar into Winding bar while carefully looseningPull Rope Side LockOperator Framing Members Perforated Angle Trolley OperatorHeader Door ARM to Operator Bracket Perforated OPERATORangle railPainting CleaningPainting Lifetime Limited Warranty Model Thank you for your purchase /or Ship Any Parts You May Need
Related manuals
Manual 20 pages 42.88 Kb Manual 4 pages 60.02 Kb Manual 26 pages 11.64 Kb Manual 38 pages 17.26 Kb Manual 18 pages 4.37 Kb

9800 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.