Wayne-Dalton 9800 installation instructions Rear Support, Keep horizontal track, Death

Page 25

19

Rear Support

DOOR IN THE

WARNING

UP POSITION

Tools Needed:

 

 

 

Ratchet Wrench

Keep horizontal track

 

 

 

1/2” Socket

parallel and within 3/4”

 

maximum of door edge,

 

 

 

1/2” Wrench

otherwise door could fall,

 

 

resulting in severe injury or

 

(2) Vice Clamps

death.

 

 

Raise the door until the top section and

 

 

half of the next section are in a horizontal

 

 

position. Do not raise door any further

 

 

since rear of horizontal track is not yet

 

 

supported.

vice

 

WARNING

clamps

 

 

 

Raising door further can

 

 

result in door falling and

 

 

cause severe injury or death.

 

 

Clamp a pair of vice clamps on the

 

 

vertical tracks just above the second

vertical

 

roller on one side, just below the second

 

TRACK

 

roller on the other side. This will prevent

 

 

 

the door from raising or lowering while

 

 

installing the rear support.

 

Using perforated angle, 5/16” x 1-5/8” hex head lag screws and 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”- 18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door.

NOTE: If rear supports are to be installed over drywall, use 5/16” x 2” hex head lag screws.

Adjust weather seal or door stop (if

 

necessary) Now permanently attach the

 

weather seal or door stop to both door

Door Edge

jambs and header. (Temporarily attached

 

in PREPARING THE OPENING on page 10.)

 

Avoid pushing weather seal or door stop

 

too tightly against face of door.

3/4”

WARNING

Horizontal Track

Prior to winding or making

 

adjustments to the springs,

 

ensure you’re winding in the

 

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts 25 You May Need. You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

INSTALLATION

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Portland Source Plant SeriesTable of Contents Package Contents Door Section Identification Tools Required Power DrillSaw horses pair Torsion Spring Removal For Standard Lift Spring when the set screws areFailure to use approved Experienced door technician. Instead haveUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Removing the Old Door Extension Spring RemovalFailure to securely Preparing the OpeningAttach a suitable Mounting pad to structurally soundAttaching Fully Adjustable Flagangle to Vertical Track InstallationHand tighten the flagangle to None Carriage bolts and 2 1/4- 20 flangeInstalling Fully Adjustable Jamb Brackets Bottom Section Counterbalance CablesTools Needed Important The tops Vertical TrackSide, must be raised the height Shim Position the left hand vertical trackStacking Sections Top Brackets Operator Bracket ANY U-BARS Provided with DOOR. the InstallationTo this DOOR, a WAYNE-DALTON ProperlyDoor Operation Top SectionAdjusting Top Brackets Attaching Horizontal Track to AdjustableFlagangle Do not Raise Door Until HorizontalCenter Bearing Bracket Side Torsion Spring AssemblyNylon Center Bushing For Spring Winding Securing DoorImportant do not USE Impact GUN To Wind Springs Winding Torsion Springs Keep horizontal track Rear SupportParallel and within 3/4 Maximum of door edge Otherwise door could fall Resulting in severe injury orThird roller. Insert a winding bar into To adjust spring tension, fully closeWinding bar while carefully loosening Set screws in the winding conePull Rope Side LockHeader Door ARM to Operator Bracket Trolley OperatorPerforated OPERATORangle rail Operator Framing Members Perforated AnglePainting CleaningPainting Lifetime Limited Warranty Model Thank you for your purchase /or Ship Any Parts You May Need
Related manuals
Manual 20 pages 42.88 Kb Manual 4 pages 60.02 Kb Manual 26 pages 11.64 Kb Manual 38 pages 17.26 Kb Manual 18 pages 4.37 Kb

9800 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.
Top Page Image Contents