Wayne-Dalton 9800 installation instructions Nylon Center Bushing

Page 22

15	Nylon Center Bushing
	Nylon Center Bushing
Tools Needed:	Slide the nylon center bushing into the		Torsion
9/16” Socket	stationary spring cone at the end of the		Spring
9/16” Socket	spring and align the stationary spring
Ratchet Wrench	cone(s) with the holes in the center	Center bearing	Stationary
Ratchet Wrench	bearing bracket. Secure the spring(s) to	Center bearing	Spring cone
	the center bearing bracket with	bracket
9/16” Wrench	the center bearing bracket with
9/16” Wrench	(2) 3/8”- 16 x 1-1/2” hex head bolts
	(2) 3/8”- 16 x 1-1/2” hex head bolts
	and (2) 3/8”-16 nuts.
	IMPORTANT: Springs under tension
	can be dangerous.
	IMPORTANT: The spring warning	Stationary
	tag(s) supplied must be securely	Spring cone
	attached to the stationary spring
	cone in plain view. Should a
	replacement spring warning tag	Nylon center
	be required, contact Wayne-	bushing
	be required, contact Wayne-
	Dalton Corp. for free
	replacements.
		Torsion
		Spring
		Center bearing
		bracket
			(2) 3/8”-16 Nut
		Torsion
		Spring
		(2) 3/8”-16 x 1-1/2”
		hex head bolt
22 Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts
You May Need. You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 22

Contents Series Portland Source PlantTable of Contents Package Contents Door Section Identification Tools Required Power DrillSaw horses pair Failure to use approved Spring when the set screws areTorsion Spring Removal For Standard Lift Experienced door technician. Instead haveTorqueMaster Spring Removal Unwind SpringsBracket and Drive Gear Extension Spring Removal Removing the Old DoorAttach a suitable Preparing the OpeningFailure to securely Mounting pad to structurally soundHand tighten the flagangle to InstallationAttaching Fully Adjustable Flagangle to Vertical Track None Carriage bolts and 2 1/4- 20 flangeInstalling Fully Adjustable Jamb Brackets Counterbalance Cables Bottom SectionSide, must be raised the height Shim Vertical TrackTools Needed Important The tops Position the left hand vertical trackStacking Sections Top Brackets To this DOOR, a WAYNE-DALTON ANY U-BARS Provided with DOOR. the InstallationOperator Bracket ProperlyTop Section Door Operation Flagangle Attaching Horizontal Track to Adjustable Adjusting Top Brackets Do not Raise Door Until HorizontalCenter Bearing Bracket Torsion Spring Assembly SideNylon Center Bushing For Spring Winding Securing DoorImportant do not USE Impact GUN To Wind Springs Winding Torsion Springs Parallel and within 3/4 Maximum of door edge Rear SupportKeep horizontal track Otherwise door could fall Resulting in severe injury orWinding bar while carefully loosening To adjust spring tension, fully closeThird roller. Insert a winding bar into Set screws in the winding coneSide Lock Pull RopePerforated OPERATORangle rail Trolley OperatorHeader Door ARM to Operator Bracket Operator Framing Members Perforated AngleCleaning PaintingPainting Lifetime Limited Warranty Model /or Ship Any Parts You May Need Thank you for your purchase

Related manuals

Manual 20 pages 42.88 Kb

Manual 4 pages 60.02 Kb

Manual 26 pages 11.64 Kb

Manual 38 pages 17.26 Kb

Manual 18 pages 4.37 Kb