![](/images/new-backgrounds/1055784/5578427x1.webp)
| 3 Litre | |
Air | Top Up Bottle | |
(if required) | ||
Vent | ||
|
| Pressure | Filling |
|
Safety | Point |
| |
Gauge |
|
| |
Valve |
|
| |
| Pump |
| |
|
|
| |
| Expansion | Radiator | |
| Circuit | ||
| Vessel | ||
|
| ||
Boiler |
|
|
|
| System Drains at |
| |
| Low Point |
|
|
Max Boiler Flow
Fig. 13 | Temp = 82° C |
Method of determining minimum expansion
vessel volume for sealed systems.
|
| Multiply Total | |
Vessel Charge | Initial System | Water Content Of | |
Pressure (Bar) | Pressure (Bar) | System By (Litres) | |
|
|
| |
| 0.5 | 0.067 | |
0.5 | 1.0 | 0.112 | |
1.5 | 0.207 | ||
| |||
| 2.0 | 0.441 | |
|
|
| |
1.0 | 1.0 | 0.087 | |
1.5 | 0.152 | ||
| |||
| 2.0 | 0.330 | |
|
|
| |
1.5 | 1.5 | 0.125 | |
2.0 | 0.265 | ||
| |||
|
|
|
Table. 1 | Example :- | System Volume = 75 litres |
| Vessel Charge Pressure = 1.0 bar | |
|
| |
|
| Initial System Pressure = 1.5 bar |
| Then :- | 75 x 0.152 = 11.4 litres |
Expansion Vessel Volume
NOTE
Where a vessel of the calculated size is not obtainable then
the next available larger size should be used.
Stop | Double |
|
Check | Stop | |
Valve | Valve | Valve |
Mains |
|
|
Inlet |
|
|
| Temporary | CH |
| Hose | |
| Return | |
Fig. 14 |
| |
|
|
6.0System Details
6.7Sealed Systems (Fig. 13)
1.SAFETY VALVE - A safety valve complying with the requirements of BS 6750 Part 1 must be fitted close to the boiler on the flow pipe by means of a horizontal or vertically upward connection with no intervening valve or restrictions and should be positioned to facilitate testing. The valve should be
2.PRESSURE GAUGE - A pressure gauge of minimum range
3.EXPANSION VESSEL - An expansion vessel complying with the requirements of BS 4814 must be fitted to the system by means of a connection close to the inlet side of the circulating pump in accordance with the manufacturers instructions, the connecting pipe being unrestricted and not less than 15mm (1/2 in) nominal size. The volume of the vessel should be suitable for the system water content and the nitrogen or air charge pressure should not be less than the system static head (See Table. 1).
Further details of sealed system design can be obtained from BS 5449 and the British Gas publication entitled 'Specifications for Domestic Wet Central Heating Systems'.
4.FILLING POINT - A filling point connection on the central heating return pipework must be provided to facilitate initial filling and pressurising and also any subsequent water loss replacement / refilling. The sealed primary circuits may be filled or replenished by means of a temporary connection between the primary circuit and a supply pipe provided a ‘Listed’ double check valve or some other no less effective backflow prevention device is permanently connected at the inlet to the circuit and the temporary connection is removed after use. The filling method adopted must be in accordance with all relevant water supply regulations and use approved equipment.
Your attention is drawn to, for GB: Guidance G24.2 and recommendation R24.2 of the Water Regulations Guide. for IE: the current edition of I.S. 813 “Domestic Gas Installations”.
5.MAKE UP SYSTEM - A method of replacing water lost from the system should be provided either by means of a make up vessel of not more than 3 litres (5 pints) capacity, mounted above the highest point of the system, or by
6.VENTING - A method of venting the system during filling and commissioning must be provided by fitting automatic air vents or by venting manually.
7.HOT WATER STORAGE - The hot water storage vessel must be of the indirect coil type.
8.COMPONENTS - All components used in the system must be suitable for operation at 110°C (230°F) and at the pressure allowed by the safety valve.
14© Baxi Heating UK Ltd 2011