Sears 139.53915D owner manual Hang the Opener

Page 16

INSTALLATION STEP 5

Hang the Opener

Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are not provided.

1.Measure the distance from each side of the motor unit to the structural support.

2.Cut both pieces of the hanging bracket to required lengths.

3.Drill 3/16" pilot holes in the structural supports.

4.Attach one end of each bracket to a support with 5/16"-18xl -7/8" lag screws.

5.Fasten the opener to the hanging brackets with 5/16"-18x7/8" hex bolts, lock washers and nuts.

6.Check to make sure the rail is centered over the door (or in line with the header bracket if the bracket is not centered above the door).

7.Remove the 2x4. Operate the door manually. If the door hits the rail, raise the header bracket.

NOTE: DO NOT connect power to opener at this time.

To avoid possible SERIOUSINJURYfrom a falling garage door opener, fasten it SECURELYto structural supports of the garage. Concreteanchors MUST be used if installing any brackets into masonry.

Figure 1_i

 

//Supports al

Measure

',

 

 

Distance

Lag Screws

 

 

 

 

 

 

5/16"

18xl

7/8"

Bolt 5/16"

18x7/8"

 

 

Nut 5/16"

18

 

 

 

Figure 2

 

Bolt 5/16"

 

Lock Washer 5/16"

HARDWARE SHOWN ACTUAL SIZE

Nut 5/16" 18

 

 

 

©

Figure 3

 

 

 

 

 

 

 

 

 

 

 

 

5/16"

18xl

 

7/8"

_ _ _ _ _

//_

 

_-

 

 

Hex

Bolt

 

Lag

Screws

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5/16"

18x7/8"

Nut 5/16" 18

Lock Washer 5/16"

 

_ -

-

- - - -

-

FINISHED CEILING

 

 

 

 

 

 

 

 

 

 

 

(Not

Provided)

 

 

 

 

 

 

 

 

 

 

 

Bolt

5/16"

18x7/8"

 

 

 

 

 

_

 

 

 

 

Lock

Washer 5/16"

 

 

 

Bolt 5/16"

18x7/8"

 

 

 

Nut

5/16"

18

 

 

 

Lock Washer

 

5/16"

 

 

 

 

 

 

 

 

 

Nut 5/16"

18

 

 

 

 

 

 

 

16

Image 16
Contents RRFTSMAN+I Contents IntroductionTools needed Preparing your garage doorSectional Door Installation Sectional Door InstallationsPlanning ONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track Carton Inventory SECURITY,¥Installation Hardware Assembly HardwareHardware Inventory Assembly Step Assemble the Rail & Install the TrolleyInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Belt and Attach the Belt Cap Retainer Installation Assembly StepReadand Followall Installationwarningsand Instructions DeathInstallation Step Determine the Header Bracket LocationWall Header Bracket Installation Install the Header BracketCeiling Header Bracket Installation Attach Rail to Header Bracket Position the Opener Sectional Door or ONE-PIECE Door with TrackHang the Opener Install Door Control Connecting Multiple Door controlsOpener, twist same color wires together. Insert wires into Quick-connect holes white to white and red/white to redInstall the Lights Attach the Emergency Release Rope and HandleElectrical Requirements Install The Protector System Important Information about the Safety Reversing SensorInstalling the Brackets Garage door track installation preferredWall installation Floor installation FigureMounting and Wiring the Safety Reversing Sensors Aligning the Safety Reversing SensorsTroubleshooting the Safety Reversing SensorsFasten the Door Bracket Will not need the door bracket proceed to Installation StepSectional Doors ONE-PIECEDOORS Connect Door Arm to Trolley Sectional Doors onlyAdjustment procedures, Figure ALL ONE-PIECE DoorsAssemble the door arm, Figure Connect the door arm to the trolleyAdjustment Step Adjust the UP and Down Travel LimitsIf door does not open at least 5 feet 1.5 m If the door does not close completelyAdjust the Force HOW and When to Adjust the ForcesTest the Down close force Test the UP open forceTest the Safety Reversal System AdjustImportant Safety Check Test The Protector SystemUsing Your Garage Door Opener OperationReadand Followall Warningsand Instructions Activate your opener with any of the followingUsing the Wall.Mounted Door Control FeatureTo Open the Door Manually Motion Detecting ControlLimit and Force Adjustments Maintenance ScheduleRemote Control Battery Care of Your OpenerHaving a PROBLEM? Refer to Adjustment , Adjust the ForceSymptom LED is not fit on door control Symptom Motor unit doesnt operateProgramming To Add or Reprogram Hand.held Remote ControlTo Erase All Codes From Motor Function Remotes Unit Memory To change an existing, known PIN To Add, Reprogram or Change a Keyless Entry PINTo set a temporary PIN Repair Parts Rail Assembly PartsInstallation Parts KEY Part NO. noMotor Unit Assembly Parts DescriptionAccessories WarrantyParts & Service Available Only Through SearsContenido Preparaci6n de la puerta de su cochera Herramientas necesariasPlanificaci6n Instalacion CON UNA Puerta SeccionalPlanificaci6n continba Instalacion CON Puertas DE UNA Sola PiezaPuerta DE UNA Sola Pieza SIN Carril Puerta DE UNA Pieza CON CarrilInventario de la caja de cart6n SECURITY.,ITornillera Y Piezas Para EL Montaje Inventario de piezasTornillera Y Piezas Para LA Instalacion MONTAJE, Paso Monte el riel e instale el troleFije el riel a la unidad del motor Instale la polea IocaInstale la banda y sujete el retn de la Cubierta de la banda Fije la tensibn de la banda InstalacionYa termino de armar su abridor de puerta de cochera. Lea INSTALACION, Paso Determine dbnde va a instalar la m6nsula Del cabezalInstale la m6nsula del cabezal Instalacion DE LA Mensula DEL Cabezal EN EL Cielo RasoColoque el riel en la m6nsula del cabezal Coloque el abridor en posici6n Puerta DE UNA Sola Pieza SIN CarrilCuelgue el abridor No se incluyenInstale Unidad Control Puerta Instalacion PasoIiiiiiiiiiiiiiiiiiii Instale las luces Coloque la manija y la cuerda De emergenciaRequisitos para la instalaci6n el6ctrica Cableado PermanenteDelsco, 6 u,g o, ,so Instale la Sistema de Protecci6nInetalacion en la pared Figura 2 y Instalacion DE LAS M#NSULASInstalacion en el pieo Figura Como Alinear LOS Sensores DE Seguridad DE Reversa Fije la mnsula de la puerta Puertas SeccionalesPuertas DE UNA Sola Pieza Conecte el brazo de la puerta al trole Solo Para Puertas SeccionalesTodas LAS Puertas DE UNA Sola Pieza Arme el brazo de la puerta, FiguraAjuste el limite del recorrido Hacia Arriba y Hacia Abajo AJUSTES, PasoComo Y Cuando Ajustar LOS Lmites Ajuste la fuerza Pruebe la fuerza del recorrido HAClA Abajo cerrarPruebe el sistema de retroceso de seguridad Pruebe la Sistema de Protecci6nPrueba Conserveestasinstrucciones OperacionC6mo Usar su Abridor de Puerta de Cochera Active su abridor de alguna de las siguientes manerasC6mo usar la unidad de control de pared C6mo abrir la puerta manualmenteLA Consola DE Control DE Deteccion DE Movienmento Como Desconectar EL TroleMantenimiento DE SU Abridor DE Puerta DE Cochera LA Bateria DEL Control Remoto Ajustes DE Limite Y FuerzaCalendario DE Mantenimiento Una vez al ruesSI Tiene Algon Problema El control remoto no activa la puertaSfntoma Una o ambas De los SensoresDe reversa no El circuito de los sensoresC6mo agregar o reprogramar Un control remoto Manual Como Programar EL AbridorControles remotos de 3 funciones C6mo Agregar, reprogramar Un c6digo de entrada Sin IlaveGarantja AccesoriosSolo estan disponibles a traves de Refacciones Servicio SearsYour Home

139.53915D specifications

The Sears 139.53915D is a significant addition to the lineup of garage door openers, blending both functionality and modern technology to enhance user convenience. This model is designed to accommodate residential garage doors, forming a reliable solution for homeowners who prioritize safety, security, and ease of use.

One of the standout features of the 139.53915D is its powerful motor, capable of handling heavy garage doors with ease. With its 1/2 horsepower motor, it ensures a smooth and swift opening and closing mechanism, allowing for quick access while still maintaining durability. This strength is particularly beneficial for larger or heavier doors that require more power for reliable operation.

The opener utilizes a chain drive system, renowned for its durability and strength. Chain drive systems are highly effective in providing reliable performance, making them a popular choice for various households. Despite this robust mechanism, the opener remains relatively quiet during operation, minimizing disruptions in the home environment.

A key characteristic of the Sears 139.53915D is its security features. It is equipped with rolling code technology, which generates a new code every time the remote control is used. This significantly enhances security by preventing unauthorized access and ensuring that only designated users can operate the garage door.

Additionally, the model features a safety reverse system, which automatically reverses the door's direction if it encounters an obstruction while closing. This not only protects vehicles and other possessions but also safeguards pets and children—an essential component for family households.

Installation of the Sears 139.53915D is designed to be straightforward, with comprehensive instructions that facilitate an efficient setup process. For those who prefer a seamless experience, the opener is compatible with several accessories, including smart home technologies. This compatibility allows users to integrate their garage door opener into a broader home automation system, providing added convenience and control through smartphone apps or smart devices.

In summary, the Sears 139.53915D garage door opener is a robust, reliable choice for homeowners seeking an efficient and secure opening mechanism. Its combination of a powerful motor, durable chain drive system, advanced security features, and ease of installation make it a formidable option in the market for garage door solutions.