Sears 139.53915D owner manual Electrical Requirements

Page 19

INSTALLATION STEP 9

Electrical Requirements

To avoid installation difficulties, do not run the opener at this time.

To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet.

RIGHT_WRONG_

If permanent wiring is required by your local code, refer to the following procedure.

To make a permanent connection through the 7/8" hole in the top of the motor unit:

•Remove the motor unit cover screws and set the cover aside.

•Remove the attached 3-prong cord.

•Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded.

•Reinstall the cover.

To avoid installation difficulties, do not run the opener at this time.

To prevent possible SERIOUSINJURYor DEATHfrom electrocution or fire:

•Besure power is not connected to the opener, and disconnect power to circuit BEFOREremoving cover to establish permanentwiring connection.

•Garagedoor installation and wiring MUST be in compliance with ALL local electrical and building codes.

•NEVERuse an extension cord, 2-wire adapter or change plug in any way to makeit fit outlet. Besure the opener is grounded.

PERMANENT WIRING

CONNECTION

Ground Tab

Green

Ground Screw

 

Black

Ground Wire

Wire

White Wire

Wire

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents RRFTSMAN+I Introduction ContentsPreparing your garage door Tools neededSectional Door Installation Sectional Door InstallationsPlanning ONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track SECURITY,¥ Carton InventoryInstallation Hardware Assembly HardwareHardware Inventory Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Belt and Attach the Belt Cap Retainer Death InstallationAssembly Step Readand Followall Installationwarningsand InstructionsDetermine the Header Bracket Location Installation StepWall Header Bracket Installation Install the Header BracketCeiling Header Bracket Installation Attach Rail to Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerHang the Opener Quick-connect holes white to white and red/white to red Install Door ControlConnecting Multiple Door controls Opener, twist same color wires together. Insert wires intoAttach the Emergency Release Rope and Handle Install the LightsElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationSensors Mounting and Wiring the Safety Reversing SensorsAligning the Safety Reversing Sensors Troubleshooting the Safety ReversingFasten the Door Bracket Will not need the door bracket proceed to Installation StepSectional Doors ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf the door does not close completely Adjustment StepAdjust the UP and Down Travel Limits If door does not open at least 5 feet 1.5 mTest the UP open force Adjust the ForceHOW and When to Adjust the Forces Test the Down close forceTest The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckActivate your opener with any of the following Using Your Garage Door OpenerOperation Readand Followall Warningsand InstructionsMotion Detecting Control Using the Wall.Mounted Door ControlFeature To Open the Door ManuallyCare of Your Opener Limit and Force AdjustmentsMaintenance Schedule Remote Control BatteryRefer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlProgramming To Add or Reprogram Hand.held Remote ControlTo Erase All Codes From Motor Function Remotes Unit Memory To change an existing, known PIN To Add, Reprogram or Change a Keyless Entry PINTo set a temporary PIN KEY Part NO. no Repair PartsRail Assembly Parts Installation PartsDescription Motor Unit Assembly PartsAvailable Only Through Sears AccessoriesWarranty Parts & ServiceContenido Herramientas necesarias Preparaci6n de la puerta de su cocheraInstalacion CON UNA Puerta Seccional Planificaci6nPuerta DE UNA Pieza CON Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Sola Pieza SIN CarrilSECURITY.,I Inventario de la caja de cart6nTornillera Y Piezas Para EL Montaje Inventario de piezasTornillera Y Piezas Para LA Instalacion Monte el riel e instale el trole MONTAJE, PasoInstale la polea Ioca Fije el riel a la unidad del motorInstale la banda y sujete el retn de la Cubierta de la banda Fije la tensibn de la banda InstalacionYa termino de armar su abridor de puerta de cochera. Lea Determine dbnde va a instalar la m6nsula Del cabezal INSTALACION, PasoInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Instale la m6nsula del cabezalColoque el riel en la m6nsula del cabezal Puerta DE UNA Sola Pieza SIN Carril Coloque el abridor en posici6nNo se incluyen Cuelgue el abridorInstale Unidad Control Puerta Instalacion PasoIiiiiiiiiiiiiiiiiiii Coloque la manija y la cuerda De emergencia Instale las lucesCableado Permanente Requisitos para la instalaci6n el6ctricaInstale la Sistema de Protecci6n Delsco, 6 u,g o, ,soInetalacion en la pared Figura 2 y Instalacion DE LAS M#NSULASInstalacion en el pieo Figura Como Alinear LOS Sensores DE Seguridad DE Reversa Puertas Seccionales Fije la mnsula de la puertaPuertas DE UNA Sola Pieza Solo Para Puertas Seccionales Conecte el brazo de la puerta al troleArme el brazo de la puerta, Figura Todas LAS Puertas DE UNA Sola PiezaAjuste el limite del recorrido Hacia Arriba y Hacia Abajo AJUSTES, PasoComo Y Cuando Ajustar LOS Lmites Pruebe la fuerza del recorrido HAClA Abajo cerrar Ajuste la fuerzaPruebe el sistema de retroceso de seguridad Pruebe la Sistema de Protecci6nPrueba Active su abridor de alguna de las siguientes maneras ConserveestasinstruccionesOperacion C6mo Usar su Abridor de Puerta de CocheraComo Desconectar EL Trole C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente LA Consola DE Control DE Deteccion DE MovienmentoUna vez al rues Mantenimiento DE SU Abridor DE Puerta DE CocheraLA Bateria DEL Control Remoto Ajustes DE Limite Y Fuerza Calendario DE MantenimientoEl control remoto no activa la puerta SI Tiene Algon ProblemaEl circuito de los sensores Sfntoma Una o ambasDe los Sensores De reversa noC6mo agregar o reprogramar Un control remoto Manual Como Programar EL AbridorControles remotos de 3 funciones Un c6digo de entrada Sin Ilave C6mo Agregar, reprogramarRefacciones Servicio Sears GarantjaAccesorios Solo estan disponibles a traves deYour Home

139.53915D specifications

The Sears 139.53915D is a significant addition to the lineup of garage door openers, blending both functionality and modern technology to enhance user convenience. This model is designed to accommodate residential garage doors, forming a reliable solution for homeowners who prioritize safety, security, and ease of use.

One of the standout features of the 139.53915D is its powerful motor, capable of handling heavy garage doors with ease. With its 1/2 horsepower motor, it ensures a smooth and swift opening and closing mechanism, allowing for quick access while still maintaining durability. This strength is particularly beneficial for larger or heavier doors that require more power for reliable operation.

The opener utilizes a chain drive system, renowned for its durability and strength. Chain drive systems are highly effective in providing reliable performance, making them a popular choice for various households. Despite this robust mechanism, the opener remains relatively quiet during operation, minimizing disruptions in the home environment.

A key characteristic of the Sears 139.53915D is its security features. It is equipped with rolling code technology, which generates a new code every time the remote control is used. This significantly enhances security by preventing unauthorized access and ensuring that only designated users can operate the garage door.

Additionally, the model features a safety reverse system, which automatically reverses the door's direction if it encounters an obstruction while closing. This not only protects vehicles and other possessions but also safeguards pets and children—an essential component for family households.

Installation of the Sears 139.53915D is designed to be straightforward, with comprehensive instructions that facilitate an efficient setup process. For those who prefer a seamless experience, the opener is compatible with several accessories, including smart home technologies. This compatibility allows users to integrate their garage door opener into a broader home automation system, providing added convenience and control through smartphone apps or smart devices.

In summary, the Sears 139.53915D garage door opener is a robust, reliable choice for homeowners seeking an efficient and secure opening mechanism. Its combination of a powerful motor, durable chain drive system, advanced security features, and ease of installation make it a formidable option in the market for garage door solutions.
Top Page Image Contents