Sears 139.53915D owner manual Instalacion DE LAS M#NSULAS, Inetalacion en la pared Figura 2 y

Page 59

INSTALACION DE LAS M#NSULAS

Asegt3rese de que el abridor no este conectado a la corriente electrica.

Instale y aiinee las mensuias de manera que los sensores esten uno frente al otro en los lados opuestos de la puerta, a una distancia mAxima de 15 cm (6 pulg.) del piso. Instale las mensulas de una de las tres maneras siguientes:

Instalacion en el earril de la puerta de la eeehera (recomendada):

Desiice los brazos curvos sobre la orilla redondeada de cada uno de los carriies de la puerta, con los brazos curvos apuntando hacia la puerta. Col6quelos en su posici6n contra el costado del carril. Debe quedar ras, con el reborde pegado a la orilla posterior del carril, como se ilustra en la Figura 1.

Si el carril de su puerta no soporta la mensuia firmemente, se recomienda que la instale sobre ia pared.

Inetalacion en la pared (Figura 2 y 3):

Coloque la mensula contra la pared con los brazos curvos apuntando hacia la puerta. Cerci6rese de que haya suficiente espacio para que el rayo del sensor no este obstruido.

Si es necesario tener mas profundidad, puede usar mensulas de extension (vea Accesorios) o bloques de madera.

Use los orificios de montaje de ia mensula para marcar y taladrar los (2) orificios de 3/16 de pulgada de diAmetro a cada iado de ia puerta a una distancia maxima de 15 cm (6 pulg.) del piso.

Fije la mensula a la pared con tornillos de cabeza cuadrada (no se incluyen).

Siesta usando mensulas de extension o bloques de madera por la falta de espacio, asegQrese de que las dos unidades queden a la misma distancia de ia superficie de montaje. Asimismo, asegQrese de que no haya ninguna obstruccion.

Instalacion en el pieo (Figura 4):

Use bloques de madera o mensulas de extension (vea Accesorios) para eievar ias mensulas de los sensores de manera que ias lentes queden a una distancia maxima de 15 cm (6 pulg.) del piso.

Cuidadosamente mida e instale las unidades derecha y izquierda a la misma distancia con respecto a la pared. AsegQrese de que no haya ninguna obstruccion.

Fije al piso las mensulas para los sensores con los sujetadores para cemento, como se muestra en ia ilustracion.

ESTAS PIEZAS SE MUESTRAN EN SU TAMAI_IO REAL

Perno de coche

Tuercade mariposa

Grapas con

de 1/4-20xl/2 de pulg.

1/4-20de pulg.

aislamiento

Figura1 INSTALACION EN EL CARRIL DE LA PUERTA(LADO DERECHO)

Cardlde

\

Reborde

,# Luz

indicadora

Mensula delsensor

/

Figura2

INSTALACION EN LA PARED(LADO DERECHO)

Fije el bloque de maderaa la paredcon

_ tornillosde cabezacuadrada (No se incluyen) Luz

dicadora M_nsula

del sensor

deca_beza cuadrada

_m t-'- (No se incluyen)

Lehte - - - -

Figura3

INSTALAClON EN LA PARED (LADO DERECHO)

Mensulade extension (YeaAccesorios)

(Seincluye en el paquetede las mensulasde extensi6n)

(Se incluyeen

M_nsula

delsensor

el paquete de ,_"

 

las mensulas

indicadora

 

de extensi6n)

Lente

 

Figura4

INSTALAClON EN EL PlSO (LADO DERECHO)

i _ Usesujetadores

,_1 o pemos para

,_ concrete

(Nose induyen)

Luz

indicadora

del sensor

21

Image 59
Contents RRFTSMAN+I Introduction ContentsPreparing your garage door Tools neededPlanning Sectional Door InstallationsSectional Door Installation ONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track SECURITY,¥ Carton InventoryHardware Inventory Assembly HardwareInstallation Hardware Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Belt and Attach the Belt Cap Retainer Death InstallationAssembly Step Readand Followall Installationwarningsand InstructionsDetermine the Header Bracket Location Installation StepCeiling Header Bracket Installation Install the Header BracketWall Header Bracket Installation Attach Rail to Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerHang the Opener Quick-connect holes white to white and red/white to red Install Door ControlConnecting Multiple Door controls Opener, twist same color wires together. Insert wires intoAttach the Emergency Release Rope and Handle Install the LightsElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationSensors Mounting and Wiring the Safety Reversing SensorsAligning the Safety Reversing Sensors Troubleshooting the Safety ReversingSectional Doors Will not need the door bracket proceed to Installation StepFasten the Door Bracket ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf the door does not close completely Adjustment StepAdjust the UP and Down Travel Limits If door does not open at least 5 feet 1.5 mTest the UP open force Adjust the ForceHOW and When to Adjust the Forces Test the Down close forceTest The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckActivate your opener with any of the following Using Your Garage Door OpenerOperation Readand Followall Warningsand InstructionsMotion Detecting Control Using the Wall.Mounted Door ControlFeature To Open the Door ManuallyCare of Your Opener Limit and Force AdjustmentsMaintenance Schedule Remote Control BatteryRefer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlTo Erase All Codes From Motor Function Remotes Unit Memory To Add or Reprogram Hand.held Remote ControlProgramming To set a temporary PIN To Add, Reprogram or Change a Keyless Entry PINTo change an existing, known PIN KEY Part NO. no Repair PartsRail Assembly Parts Installation PartsDescription Motor Unit Assembly PartsAvailable Only Through Sears AccessoriesWarranty Parts & ServiceContenido Herramientas necesarias Preparaci6n de la puerta de su cocheraInstalacion CON UNA Puerta Seccional Planificaci6nPuerta DE UNA Pieza CON Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Sola Pieza SIN CarrilSECURITY.,I Inventario de la caja de cart6nTornillera Y Piezas Para LA Instalacion Inventario de piezasTornillera Y Piezas Para EL Montaje Monte el riel e instale el trole MONTAJE, PasoInstale la polea Ioca Fije el riel a la unidad del motorInstale la banda y sujete el retn de la Cubierta de la banda Ya termino de armar su abridor de puerta de cochera. Lea InstalacionFije la tensibn de la banda Determine dbnde va a instalar la m6nsula Del cabezal INSTALACION, PasoInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Instale la m6nsula del cabezalColoque el riel en la m6nsula del cabezal Puerta DE UNA Sola Pieza SIN Carril Coloque el abridor en posici6nNo se incluyen Cuelgue el abridorIiiiiiiiiiiiiiiiiiii Instalacion PasoInstale Unidad Control Puerta Coloque la manija y la cuerda De emergencia Instale las lucesCableado Permanente Requisitos para la instalaci6n el6ctricaInstale la Sistema de Protecci6n Delsco, 6 u,g o, ,soInstalacion en el pieo Figura Instalacion DE LAS M#NSULASInetalacion en la pared Figura 2 y Como Alinear LOS Sensores DE Seguridad DE Reversa Puertas Seccionales Fije la mnsula de la puertaPuertas DE UNA Sola Pieza Solo Para Puertas Seccionales Conecte el brazo de la puerta al troleArme el brazo de la puerta, Figura Todas LAS Puertas DE UNA Sola PiezaComo Y Cuando Ajustar LOS Lmites AJUSTES, PasoAjuste el limite del recorrido Hacia Arriba y Hacia Abajo Pruebe la fuerza del recorrido HAClA Abajo cerrar Ajuste la fuerzaPrueba Pruebe la Sistema de Protecci6nPruebe el sistema de retroceso de seguridad Active su abridor de alguna de las siguientes maneras ConserveestasinstruccionesOperacion C6mo Usar su Abridor de Puerta de CocheraComo Desconectar EL Trole C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente LA Consola DE Control DE Deteccion DE MovienmentoUna vez al rues Mantenimiento DE SU Abridor DE Puerta DE CocheraLA Bateria DEL Control Remoto Ajustes DE Limite Y Fuerza Calendario DE MantenimientoEl control remoto no activa la puerta SI Tiene Algon ProblemaEl circuito de los sensores Sfntoma Una o ambasDe los Sensores De reversa noControles remotos de 3 funciones Como Programar EL AbridorC6mo agregar o reprogramar Un control remoto Manual Un c6digo de entrada Sin Ilave C6mo Agregar, reprogramarRefacciones Servicio Sears GarantjaAccesorios Solo estan disponibles a traves deYour Home

139.53915D specifications

The Sears 139.53915D is a significant addition to the lineup of garage door openers, blending both functionality and modern technology to enhance user convenience. This model is designed to accommodate residential garage doors, forming a reliable solution for homeowners who prioritize safety, security, and ease of use.

One of the standout features of the 139.53915D is its powerful motor, capable of handling heavy garage doors with ease. With its 1/2 horsepower motor, it ensures a smooth and swift opening and closing mechanism, allowing for quick access while still maintaining durability. This strength is particularly beneficial for larger or heavier doors that require more power for reliable operation.

The opener utilizes a chain drive system, renowned for its durability and strength. Chain drive systems are highly effective in providing reliable performance, making them a popular choice for various households. Despite this robust mechanism, the opener remains relatively quiet during operation, minimizing disruptions in the home environment.

A key characteristic of the Sears 139.53915D is its security features. It is equipped with rolling code technology, which generates a new code every time the remote control is used. This significantly enhances security by preventing unauthorized access and ensuring that only designated users can operate the garage door.

Additionally, the model features a safety reverse system, which automatically reverses the door's direction if it encounters an obstruction while closing. This not only protects vehicles and other possessions but also safeguards pets and children—an essential component for family households.

Installation of the Sears 139.53915D is designed to be straightforward, with comprehensive instructions that facilitate an efficient setup process. For those who prefer a seamless experience, the opener is compatible with several accessories, including smart home technologies. This compatibility allows users to integrate their garage door opener into a broader home automation system, providing added convenience and control through smartphone apps or smart devices.

In summary, the Sears 139.53915D garage door opener is a robust, reliable choice for homeowners seeking an efficient and secure opening mechanism. Its combination of a powerful motor, durable chain drive system, advanced security features, and ease of installation make it a formidable option in the market for garage door solutions.