Sears 139.53915D owner manual Connect Door Arm to Trolley, Sectional Doors only

Page 25

INSTALLATION STEP 12

Connect Door Arm to Trolley

Follow instructions which apply to your door type as illustrated below and on the following page.

SECTIONAL DOORS ONLY

Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the pulley) about 8" (20 cm) as shown in Figures 1, 2 and 3.

Figure 1:

•Fasten straight door arm section to outer trolley with the

5/16"x1" clevis pin. Secure the connection with a ring fastener.

•Fasten curved section to the door bracket in the same way, using the 5/16"x1-1/4" clevis pin.

Figure 2:

•Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity.

Figure 3, Hole alignment alternative:

•If holes in curved arm are above holes in straight arm, disconnect straight arm. Cut about 6" (15 cm) from the solid end. Reconnect to trolley with cut end down as shown.

•Bring arm sections together.

•Find two pairs of holes that line up and join with bolts, lock washers and nuts.

Pull the emergency release handle toward the opener at a 45° angle so that the trolley release arm is horizontal. Proceed to Adjustment Step 1, page 27. Trolley will re-engage automatically when opener is operated.

 

HARDWARE SHOWN ACTUAL

SIZE

 

©

 

 

 

 

 

 

Nut 5/16"

18

Lock Washer

5/16"

Ring

Fastener

 

Clevis Pin

Clevis

Pin

 

 

Hex Bolt

5/16"x1"

(Trolley)

5/16"xl

1/4"

(Door

Bracket)

5/16" 18x7/8"

Trolley

 

Stop

Bolt

Trolley

 

 

 

Ring

 

 

Fastener

5/16"x1"

 

/

 

 

/J

 

Emergency

0

Door

Release

 

 

Handle

 

 

Door Arm

Clevis

Pin ,: I_ _

Curved Door Arm

5/16"xl

1/4"

 

Figure 1

Bolts

Door Bracket

Figure 2

Pulley

", i

 

i

_"IL8"

(20 cm)rnin

_',

_ "_---

_

"--71

Trolley _J_

Stop Bolt //// !

Lock /o/

Washers/m/

Nuts 5/16" /o/

5/16" _8 @_ #

Figure 3

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents RRFTSMAN+I Introduction ContentsPreparing your garage door Tools neededSectional Door Installation Sectional Door InstallationsPlanning ONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track SECURITY,¥ Carton InventoryInstallation Hardware Assembly HardwareHardware Inventory Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Belt and Attach the Belt Cap Retainer Assembly Step InstallationReadand Followall Installationwarningsand Instructions DeathDetermine the Header Bracket Location Installation StepWall Header Bracket Installation Install the Header BracketCeiling Header Bracket Installation Attach Rail to Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerHang the Opener Connecting Multiple Door controls Install Door ControlOpener, twist same color wires together. Insert wires into Quick-connect holes white to white and red/white to redAttach the Emergency Release Rope and Handle Install the LightsElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemGarage door track installation preferred Installing the BracketsWall installation Floor installation FigureAligning the Safety Reversing Sensors Mounting and Wiring the Safety Reversing SensorsTroubleshooting the Safety Reversing SensorsFasten the Door Bracket Will not need the door bracket proceed to Installation StepSectional Doors ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyALL ONE-PIECE Doors Adjustment procedures, FigureAssemble the door arm, Figure Connect the door arm to the trolleyAdjust the UP and Down Travel Limits Adjustment StepIf door does not open at least 5 feet 1.5 m If the door does not close completelyHOW and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceAdjust Test the Safety Reversal SystemImportant Safety Check Test The Protector SystemOperation Using Your Garage Door OpenerReadand Followall Warningsand Instructions Activate your opener with any of the followingFeature Using the Wall.Mounted Door ControlTo Open the Door Manually Motion Detecting ControlMaintenance Schedule Limit and Force AdjustmentsRemote Control Battery Care of Your OpenerRefer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlProgramming To Add or Reprogram Hand.held Remote ControlTo Erase All Codes From Motor Function Remotes Unit Memory To change an existing, known PIN To Add, Reprogram or Change a Keyless Entry PINTo set a temporary PIN Rail Assembly Parts Repair PartsInstallation Parts KEY Part NO. noDescription Motor Unit Assembly PartsWarranty AccessoriesParts & Service Available Only Through SearsContenido Herramientas necesarias Preparaci6n de la puerta de su cocheraInstalacion CON UNA Puerta Seccional Planificaci6nInstalacion CON Puertas DE UNA Sola Pieza Planificaci6n continbaPuerta DE UNA Sola Pieza SIN Carril Puerta DE UNA Pieza CON CarrilSECURITY.,I Inventario de la caja de cart6nTornillera Y Piezas Para EL Montaje Inventario de piezasTornillera Y Piezas Para LA Instalacion Monte el riel e instale el trole MONTAJE, PasoInstale la polea Ioca Fije el riel a la unidad del motorInstale la banda y sujete el retn de la Cubierta de la banda Fije la tensibn de la banda InstalacionYa termino de armar su abridor de puerta de cochera. Lea Determine dbnde va a instalar la m6nsula Del cabezal INSTALACION, PasoInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Instale la m6nsula del cabezalColoque el riel en la m6nsula del cabezal Puerta DE UNA Sola Pieza SIN Carril Coloque el abridor en posici6nNo se incluyen Cuelgue el abridorInstale Unidad Control Puerta Instalacion PasoIiiiiiiiiiiiiiiiiiii Coloque la manija y la cuerda De emergencia Instale las lucesCableado Permanente Requisitos para la instalaci6n el6ctricaInstale la Sistema de Protecci6n Delsco, 6 u,g o, ,soInetalacion en la pared Figura 2 y Instalacion DE LAS M#NSULASInstalacion en el pieo Figura Como Alinear LOS Sensores DE Seguridad DE Reversa Puertas Seccionales Fije la mnsula de la puertaPuertas DE UNA Sola Pieza Solo Para Puertas Seccionales Conecte el brazo de la puerta al troleArme el brazo de la puerta, Figura Todas LAS Puertas DE UNA Sola PiezaAjuste el limite del recorrido Hacia Arriba y Hacia Abajo AJUSTES, PasoComo Y Cuando Ajustar LOS Lmites Pruebe la fuerza del recorrido HAClA Abajo cerrar Ajuste la fuerzaPruebe el sistema de retroceso de seguridad Pruebe la Sistema de Protecci6nPrueba Operacion ConserveestasinstruccionesC6mo Usar su Abridor de Puerta de Cochera Active su abridor de alguna de las siguientes manerasC6mo abrir la puerta manualmente C6mo usar la unidad de control de paredLA Consola DE Control DE Deteccion DE Movienmento Como Desconectar EL TroleLA Bateria DEL Control Remoto Ajustes DE Limite Y Fuerza Mantenimiento DE SU Abridor DE Puerta DE CocheraCalendario DE Mantenimiento Una vez al ruesEl control remoto no activa la puerta SI Tiene Algon ProblemaDe los Sensores Sfntoma Una o ambasDe reversa no El circuito de los sensoresC6mo agregar o reprogramar Un control remoto Manual Como Programar EL AbridorControles remotos de 3 funciones Un c6digo de entrada Sin Ilave C6mo Agregar, reprogramarAccesorios GarantjaSolo estan disponibles a traves de Refacciones Servicio SearsYour Home

139.53915D specifications

The Sears 139.53915D is a significant addition to the lineup of garage door openers, blending both functionality and modern technology to enhance user convenience. This model is designed to accommodate residential garage doors, forming a reliable solution for homeowners who prioritize safety, security, and ease of use.

One of the standout features of the 139.53915D is its powerful motor, capable of handling heavy garage doors with ease. With its 1/2 horsepower motor, it ensures a smooth and swift opening and closing mechanism, allowing for quick access while still maintaining durability. This strength is particularly beneficial for larger or heavier doors that require more power for reliable operation.

The opener utilizes a chain drive system, renowned for its durability and strength. Chain drive systems are highly effective in providing reliable performance, making them a popular choice for various households. Despite this robust mechanism, the opener remains relatively quiet during operation, minimizing disruptions in the home environment.

A key characteristic of the Sears 139.53915D is its security features. It is equipped with rolling code technology, which generates a new code every time the remote control is used. This significantly enhances security by preventing unauthorized access and ensuring that only designated users can operate the garage door.

Additionally, the model features a safety reverse system, which automatically reverses the door's direction if it encounters an obstruction while closing. This not only protects vehicles and other possessions but also safeguards pets and children—an essential component for family households.

Installation of the Sears 139.53915D is designed to be straightforward, with comprehensive instructions that facilitate an efficient setup process. For those who prefer a seamless experience, the opener is compatible with several accessories, including smart home technologies. This compatibility allows users to integrate their garage door opener into a broader home automation system, providing added convenience and control through smartphone apps or smart devices.

In summary, the Sears 139.53915D garage door opener is a robust, reliable choice for homeowners seeking an efficient and secure opening mechanism. Its combination of a powerful motor, durable chain drive system, advanced security features, and ease of installation make it a formidable option in the market for garage door solutions.
Top Page Image Contents