Sears 139.53915D owner manual Tools needed, Preparing your garage door

Page 3

Preparing your garage door

Before you begin:

•Disable locks.

•Remove any ropes connected to garage door.

•Complete the following test to make sure your garage door is balanced and is not sticking or binding:

1.Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs.

2.Raise and lower the door to see if there is any binding or sticking.

If your door binds, sticks, or is out of balance, call a trained door systems technician.

Sectional Door

One-Piece Door

To prevent possible SERIOUSINJURYor DEATH:

•ALWAYScall a trained door systems technician if garage door binds, sticks or is out of balance An unbalancedgarage door may not reversewhen required

•NEVERtry to loosen, move or adjust garagedoor, door

springs, cables, pulleys, brackets or their hardware,ALL of which are under EXTREMEtension

•DisableALL locks and removeALL ropes connected to garagedoor BEFOREinstalling and operating garagedoor openerto avoid entanglement.

To prevent damage to garage door and opener:

•ALWAYSdisable locks BEFOREinstalling and operating the opener.

•ONLYoperate garagedoor opener at 120V,60 Hzto avoid malfunction and damage.

Tools needed

During assembly, installation and adjustment of the

opener, instructions will call for hand tools as illustrated below.

Level (optional)

Pencil

Hack Saw

Tape Measure

Wire Cutters

Screwdriver

Stepladder

Adjustable End Wrench

Page 2 Page 4
Image 3
Page 2 Page 4
Contents RRFTSMAN+I Introduction ContentsPreparing your garage door Tools neededSectional Door Installations Sectional Door InstallationPlanning ONE-PIECE Door Installations ONE-PIECE Door Without TrackONE-PIECE Door with Track SECURITY,¥ Carton InventoryAssembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Belt and Attach the Belt Cap Retainer Death InstallationAssembly Step Readand Followall Installationwarningsand InstructionsDetermine the Header Bracket Location Installation StepInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach Rail to Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerHang the Opener Quick-connect holes white to white and red/white to red Install Door ControlConnecting Multiple Door controls Opener, twist same color wires together. Insert wires intoAttach the Emergency Release Rope and Handle Install the LightsElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationSensors Mounting and Wiring the Safety Reversing SensorsAligning the Safety Reversing Sensors Troubleshooting the Safety ReversingWill not need the door bracket proceed to Installation Step Fasten the Door BracketSectional Doors ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf the door does not close completely Adjustment StepAdjust the UP and Down Travel Limits If door does not open at least 5 feet 1.5 mTest the UP open force Adjust the ForceHOW and When to Adjust the Forces Test the Down close forceTest The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckActivate your opener with any of the following Using Your Garage Door OpenerOperation Readand Followall Warningsand InstructionsMotion Detecting Control Using the Wall.Mounted Door ControlFeature To Open the Door ManuallyCare of Your Opener Limit and Force AdjustmentsMaintenance Schedule Remote Control BatteryRefer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlTo Add or Reprogram Hand.held Remote Control ProgrammingTo Erase All Codes From Motor Function Remotes Unit Memory To Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PINTo set a temporary PIN KEY Part NO. no Repair PartsRail Assembly Parts Installation PartsDescription Motor Unit Assembly PartsAvailable Only Through Sears AccessoriesWarranty Parts & ServiceContenido Herramientas necesarias Preparaci6n de la puerta de su cocheraInstalacion CON UNA Puerta Seccional Planificaci6nPuerta DE UNA Pieza CON Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Sola Pieza SIN CarrilSECURITY.,I Inventario de la caja de cart6nInventario de piezas Tornillera Y Piezas Para EL MontajeTornillera Y Piezas Para LA Instalacion Monte el riel e instale el trole MONTAJE, PasoInstale la polea Ioca Fije el riel a la unidad del motorInstale la banda y sujete el retn de la Cubierta de la banda Instalacion Fije la tensibn de la bandaYa termino de armar su abridor de puerta de cochera. Lea Determine dbnde va a instalar la m6nsula Del cabezal INSTALACION, PasoInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Instale la m6nsula del cabezalColoque el riel en la m6nsula del cabezal Puerta DE UNA Sola Pieza SIN Carril Coloque el abridor en posici6nNo se incluyen Cuelgue el abridorInstalacion Paso Instale Unidad Control PuertaIiiiiiiiiiiiiiiiiiii Coloque la manija y la cuerda De emergencia Instale las lucesCableado Permanente Requisitos para la instalaci6n el6ctricaInstale la Sistema de Protecci6n Delsco, 6 u,g o, ,soInstalacion DE LAS M#NSULAS Inetalacion en la pared Figura 2 yInstalacion en el pieo Figura Como Alinear LOS Sensores DE Seguridad DE Reversa Puertas Seccionales Fije la mnsula de la puertaPuertas DE UNA Sola Pieza Solo Para Puertas Seccionales Conecte el brazo de la puerta al troleArme el brazo de la puerta, Figura Todas LAS Puertas DE UNA Sola PiezaAJUSTES, Paso Ajuste el limite del recorrido Hacia Arriba y Hacia AbajoComo Y Cuando Ajustar LOS Lmites Pruebe la fuerza del recorrido HAClA Abajo cerrar Ajuste la fuerzaPruebe la Sistema de Protecci6n Pruebe el sistema de retroceso de seguridadPrueba Active su abridor de alguna de las siguientes maneras ConserveestasinstruccionesOperacion C6mo Usar su Abridor de Puerta de CocheraComo Desconectar EL Trole C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente LA Consola DE Control DE Deteccion DE MovienmentoUna vez al rues Mantenimiento DE SU Abridor DE Puerta DE CocheraLA Bateria DEL Control Remoto Ajustes DE Limite Y Fuerza Calendario DE MantenimientoEl control remoto no activa la puerta SI Tiene Algon ProblemaEl circuito de los sensores Sfntoma Una o ambasDe los Sensores De reversa noComo Programar EL Abridor C6mo agregar o reprogramar Un control remoto ManualControles remotos de 3 funciones Un c6digo de entrada Sin Ilave C6mo Agregar, reprogramarRefacciones Servicio Sears GarantjaAccesorios Solo estan disponibles a traves deYour Home

139.53915D specifications

The Sears 139.53915D is a significant addition to the lineup of garage door openers, blending both functionality and modern technology to enhance user convenience. This model is designed to accommodate residential garage doors, forming a reliable solution for homeowners who prioritize safety, security, and ease of use.

One of the standout features of the 139.53915D is its powerful motor, capable of handling heavy garage doors with ease. With its 1/2 horsepower motor, it ensures a smooth and swift opening and closing mechanism, allowing for quick access while still maintaining durability. This strength is particularly beneficial for larger or heavier doors that require more power for reliable operation.

The opener utilizes a chain drive system, renowned for its durability and strength. Chain drive systems are highly effective in providing reliable performance, making them a popular choice for various households. Despite this robust mechanism, the opener remains relatively quiet during operation, minimizing disruptions in the home environment.

A key characteristic of the Sears 139.53915D is its security features. It is equipped with rolling code technology, which generates a new code every time the remote control is used. This significantly enhances security by preventing unauthorized access and ensuring that only designated users can operate the garage door.

Additionally, the model features a safety reverse system, which automatically reverses the door's direction if it encounters an obstruction while closing. This not only protects vehicles and other possessions but also safeguards pets and children—an essential component for family households.

Installation of the Sears 139.53915D is designed to be straightforward, with comprehensive instructions that facilitate an efficient setup process. For those who prefer a seamless experience, the opener is compatible with several accessories, including smart home technologies. This compatibility allows users to integrate their garage door opener into a broader home automation system, providing added convenience and control through smartphone apps or smart devices.

In summary, the Sears 139.53915D garage door opener is a robust, reliable choice for homeowners seeking an efficient and secure opening mechanism. Its combination of a powerful motor, durable chain drive system, advanced security features, and ease of installation make it a formidable option in the market for garage door solutions.
Top Page Image Contents