Sears 139.53915D owner manual ALL ONE-PIECE Doors, Assemble the door arm, Figure

Page 26

ALL ONE-PIECE DOORS

1.Assemble the door arm, Figure 4:

Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap).

With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis

pin.

Secure with a ring fastener.

2.Adjustment procedures, Figure 5:

On one-piece doors, before connecting the door arm to the trolley, the travel limits must be adjusted. Limit adjustment screws are located on the left side panel

as shown on page 27. Follow adjustment procedures below.

Open door adjustment: decrease UP travel limit

-Turn the UP limit adjustment screw counter-clockwise 4 turns.

-Press the Door Control push button. The trolley will travel to the fully open position.

-Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer to the fully open trolley/door arm positions in the illustration. If the arm does not extend far enough, adjust the limit further. One full turn equals 2" (5 cm) of trolley travel.

Closed door adjustment: decrease DOWN travel limit

-Turn the DOWN limit adjustment screw clockwise 4 complete turns.

Figure 5

inner Trolley

Inner Trolley

Open Door

Door

 

 

 

 

 

 

 

 

 

Bracket

_

_

_

Ring

 

 

 

 

 

 

"_-,._

 

Fastener

 

 

 

 

_

 

"'_\_ *_- -._1

 

 

 

 

Nuts

 

L_

 

"_" -_" -:..__-_*_...

 

 

Lock

 

5/16"

18

_-

 

/

"'',_

,_..

 

Washers

I

! '_I

F

v

 

 

_

_

5/16"

 

I

C,evisPin

 

Straight /

 

_,4_.._

 

_vO

/

I ,/I

5/16"xl

1/4"

Arm

 

 

"_../_,_"_'_

 

{_/

_/_

Figure

4

 

_'/_6'a''18x7/8 ''_

 

"_',m_Curved

DoorArm

 

 

 

 

 

 

 

-Press the Door Control push button. The trolley will travel to the fully closed position.

-Manually close the door and lift the door arm to the trolley. The arm should touch the trolley just ahead of the door arm connector hole. Refer to the fully closed trolley/door arm positions in the illustration. If the arm is behind the connector hole, adjust the limit further. One full turn equals 2" (5 cm) of trolley travel.

3.Connect the door arm to the trolley:

Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis

pin. It may be necessary to lift the door slightly to make the connection.

Secure with a ring fastener.

Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor.

NOTE: When setting the up limit on the following page, the door should not have a "backward" slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position.

Outer Trolley

Backward Slant (Incorrect)

26

Image 26
Contents RRFTSMAN+I Contents IntroductionTools needed Preparing your garage doorPlanning Sectional Door InstallationsSectional Door Installation ONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track Carton Inventory SECURITY,¥Hardware Inventory Assembly HardwareInstallation Hardware Assembly Step Assemble the Rail & Install the TrolleyInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Belt and Attach the Belt Cap Retainer Readand Followall Installationwarningsand Instructions InstallationAssembly Step DeathInstallation Step Determine the Header Bracket LocationCeiling Header Bracket Installation Install the Header BracketWall Header Bracket Installation Attach Rail to Header Bracket Position the Opener Sectional Door or ONE-PIECE Door with TrackHang the Opener Opener, twist same color wires together. Insert wires into Install Door ControlConnecting Multiple Door controls Quick-connect holes white to white and red/white to redInstall the Lights Attach the Emergency Release Rope and HandleElectrical Requirements Install The Protector System Important Information about the Safety Reversing SensorWall installation Installing the BracketsGarage door track installation preferred Floor installation FigureTroubleshooting the Safety Reversing Mounting and Wiring the Safety Reversing SensorsAligning the Safety Reversing Sensors SensorsSectional Doors Will not need the door bracket proceed to Installation StepFasten the Door Bracket ONE-PIECEDOORS Connect Door Arm to Trolley Sectional Doors onlyAssemble the door arm, Figure Adjustment procedures, FigureALL ONE-PIECE Doors Connect the door arm to the trolleyIf door does not open at least 5 feet 1.5 m Adjustment StepAdjust the UP and Down Travel Limits If the door does not close completelyTest the Down close force Adjust the ForceHOW and When to Adjust the Forces Test the UP open forceImportant Safety Check Test the Safety Reversal SystemAdjust Test The Protector SystemReadand Followall Warningsand Instructions Using Your Garage Door OpenerOperation Activate your opener with any of the followingTo Open the Door Manually Using the Wall.Mounted Door ControlFeature Motion Detecting ControlRemote Control Battery Limit and Force AdjustmentsMaintenance Schedule Care of Your OpenerHaving a PROBLEM? Refer to Adjustment , Adjust the ForceSymptom LED is not fit on door control Symptom Motor unit doesnt operateTo Erase All Codes From Motor Function Remotes Unit Memory To Add or Reprogram Hand.held Remote ControlProgramming To set a temporary PIN To Add, Reprogram or Change a Keyless Entry PINTo change an existing, known PIN Installation Parts Repair PartsRail Assembly Parts KEY Part NO. noMotor Unit Assembly Parts DescriptionParts & Service AccessoriesWarranty Available Only Through SearsContenido Preparaci6n de la puerta de su cochera Herramientas necesariasPlanificaci6n Instalacion CON UNA Puerta SeccionalPuerta DE UNA Sola Pieza SIN Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Pieza CON CarrilInventario de la caja de cart6n SECURITY.,ITornillera Y Piezas Para LA Instalacion Inventario de piezasTornillera Y Piezas Para EL Montaje MONTAJE, Paso Monte el riel e instale el troleFije el riel a la unidad del motor Instale la polea IocaInstale la banda y sujete el retn de la Cubierta de la banda Ya termino de armar su abridor de puerta de cochera. Lea InstalacionFije la tensibn de la banda INSTALACION, Paso Determine dbnde va a instalar la m6nsula Del cabezalInstale la m6nsula del cabezal Instalacion DE LA Mensula DEL Cabezal EN EL Cielo RasoColoque el riel en la m6nsula del cabezal Coloque el abridor en posici6n Puerta DE UNA Sola Pieza SIN CarrilCuelgue el abridor No se incluyenIiiiiiiiiiiiiiiiiiii Instalacion PasoInstale Unidad Control Puerta Instale las luces Coloque la manija y la cuerda De emergenciaRequisitos para la instalaci6n el6ctrica Cableado PermanenteDelsco, 6 u,g o, ,so Instale la Sistema de Protecci6nInstalacion en el pieo Figura Instalacion DE LAS M#NSULASInetalacion en la pared Figura 2 y Como Alinear LOS Sensores DE Seguridad DE Reversa Fije la mnsula de la puerta Puertas SeccionalesPuertas DE UNA Sola Pieza Conecte el brazo de la puerta al trole Solo Para Puertas SeccionalesTodas LAS Puertas DE UNA Sola Pieza Arme el brazo de la puerta, FiguraComo Y Cuando Ajustar LOS Lmites AJUSTES, PasoAjuste el limite del recorrido Hacia Arriba y Hacia Abajo Ajuste la fuerza Pruebe la fuerza del recorrido HAClA Abajo cerrarPrueba Pruebe la Sistema de Protecci6nPruebe el sistema de retroceso de seguridad C6mo Usar su Abridor de Puerta de Cochera ConserveestasinstruccionesOperacion Active su abridor de alguna de las siguientes manerasLA Consola DE Control DE Deteccion DE Movienmento C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente Como Desconectar EL TroleCalendario DE Mantenimiento Mantenimiento DE SU Abridor DE Puerta DE CocheraLA Bateria DEL Control Remoto Ajustes DE Limite Y Fuerza Una vez al ruesSI Tiene Algon Problema El control remoto no activa la puertaDe reversa no Sfntoma Una o ambasDe los Sensores El circuito de los sensoresControles remotos de 3 funciones Como Programar EL AbridorC6mo agregar o reprogramar Un control remoto Manual C6mo Agregar, reprogramar Un c6digo de entrada Sin IlaveSolo estan disponibles a traves de GarantjaAccesorios Refacciones Servicio SearsYour Home

139.53915D specifications

The Sears 139.53915D is a significant addition to the lineup of garage door openers, blending both functionality and modern technology to enhance user convenience. This model is designed to accommodate residential garage doors, forming a reliable solution for homeowners who prioritize safety, security, and ease of use.

One of the standout features of the 139.53915D is its powerful motor, capable of handling heavy garage doors with ease. With its 1/2 horsepower motor, it ensures a smooth and swift opening and closing mechanism, allowing for quick access while still maintaining durability. This strength is particularly beneficial for larger or heavier doors that require more power for reliable operation.

The opener utilizes a chain drive system, renowned for its durability and strength. Chain drive systems are highly effective in providing reliable performance, making them a popular choice for various households. Despite this robust mechanism, the opener remains relatively quiet during operation, minimizing disruptions in the home environment.

A key characteristic of the Sears 139.53915D is its security features. It is equipped with rolling code technology, which generates a new code every time the remote control is used. This significantly enhances security by preventing unauthorized access and ensuring that only designated users can operate the garage door.

Additionally, the model features a safety reverse system, which automatically reverses the door's direction if it encounters an obstruction while closing. This not only protects vehicles and other possessions but also safeguards pets and children—an essential component for family households.

Installation of the Sears 139.53915D is designed to be straightforward, with comprehensive instructions that facilitate an efficient setup process. For those who prefer a seamless experience, the opener is compatible with several accessories, including smart home technologies. This compatibility allows users to integrate their garage door opener into a broader home automation system, providing added convenience and control through smartphone apps or smart devices.

In summary, the Sears 139.53915D garage door opener is a robust, reliable choice for homeowners seeking an efficient and secure opening mechanism. Its combination of a powerful motor, durable chain drive system, advanced security features, and ease of installation make it a formidable option in the market for garage door solutions.